• Korean Journal of Materials Research
• /
• v.17 no.6
• /
• pp.313-317
• /
• 2007

In-situ micro-channeled multi tubular solid oxide fuel cell(SOFC) was fabricated using multi-pass extrusion process with out side diameter of 2.7 mm and active length of 5 mm that contained 61 individual cells. Cell materials used in this work were NiO-YSZ (50 : 50 vol.%), 8 mol% yttria-stabilized zirconia(8YSZ), $La_{0.8}Sr_{0.2}MnO_3(LSM)$ as anode, electrolyte, and cathode, respectively. The arrangement of each electrode and electrolyte layer in green bodies showed uniformity and integrity after extrusion and sintering. The XRD analysis confirmed that no reaction phases appeared and the microstructure of the electrolyte was fairly dense (relative density > 96%) after sintering.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1298-1300
• /
• 1997

금속기판상 초전도 $YBa_2CU_3O_{7-{\delta}}$ (YBCO) 박막을 yttria-stabilized zirconia (YSZ) 완충막을 이용하여 in situ 펄스 레이저 증착법에 의해 증착하였다. YBCO 박막을 직접 금속기판에 증착하게 되면 YBCO 박막과 금속기판 사이의 계면에서 상호확산현상이 발생하기 때문에 이를 방지하기 위해 YSZ 완충막이 사용되었다. YSZ 완충막의 증착온도가 박막의 결정성과 전기적 특성에 미치는 영향을 알아보기 위해 YSZ 완충막은 여러 가지 온도로 증착되었다. YBCO 박막의 증착온도와 같은 온도로 YSZ 완충막을 증착했을 때보다 YBCO 박막의 증착온도보다 높은 온도로 YSZ 완충막을 증착했을 경우, 증착된 YBCO 박막은 x선 회절에 의해 c 축 방향으로 성장하였음을 알 수 있었고, 저항이 0이 되는 임계온도가 83K가 되는 실험 결과를 얻었다.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.25-34
• /
• 1996

Yttria stabilized zirconia (YSZ) thin films were prepared by the electrochemical vapor deposition (EVD) method on the porous Al2O3 substrates which were fabricated by different substrate thickness and porosity. Film growth rates decreased with increase on the substrate thickness and porosity and obeyed a parabolic rate law. Activa-tion energy calculated from the parabolic rate onstants was 69.9 kcal/mol. With increase on the deposition time, monoclinic phase was appeared and then disappeared. YSZ penetrated deeply into substrates when the EVD temperature decreased. Electrical conductivity of the films was 0.09 S/cm at 100$0^{\circ}C$ similar to the value of YSZ single crystal.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.470-475
• /
• 2012

$La_{1-x}Sr_xMnO_3$(LSM,$0{\leq}x{\leq}0.5$) powders as the air electrode for solid oxide fuel cell were synthesized by a glycine-nitrate combustion process. The powders were then examined by X-ray diffraction(XRD) and scanning electron microscopy (SEM). The as-formed powders were composed of very fine ash particles linked together in chains. X-ray maps of the LSM powders milled for 1.5 h showed that the metallic elements are homogeneously distributed inside each grain and in the different grains. The powder XRD patterns of the LSM with x < 0.3 showed a rhombohedral phase; the phase changes to the cubic phase at higher compositions($x{\geq}0.3$) calcined in air at $1200^{\circ}C$ for 4 h. Also, the SEM micrographs showed that the average grain size decreases as Sr content increases. Composite air electrodes made of 50/50 vol% of the resulting LSM powders and yttria stabilized zirconia(YSZ) powders were prepared by colloidal deposition technique. The electrodes were studied by ac impedance spectroscopy in order to improve the performance of a solid oxide fuel cell(SOFC). Reproducible impedance spectra were confirmed using the improved cell, which consisted of LSM-YSZ/YSZ. The composite electrode of LSM and YSZ was found to yield a lower cathodic resistivity than that of the non-composite one. Also, the addition of YSZ to the $La_{1-x}Sr_xMnO_3$ ($0.1{\leq}x{\leq}0.2$) electrode led to a pronounced, large decrease in the cathodic resistivity of the LSM-YSZ composite electrodes.

• Korean Journal of Materials Research
• /
• v.7 no.5
• /
• pp.411-416
• /
• 1997

수소 및 산소분위기 하에서 2Y-TZP 및 3Y-PZP 세라믹스를 소결하여 각각 제조한 다음, 각 시편의 미세구조 및 25$0^{\circ}C$에서의 등온상전이 거동을 비교하여 고찰하였다. 그 결과 수소분위기에서 소결한 모든 시편의 표면에서는 Zr$_{4+}$ 이온의 환원에 의해 산화분위기에서 소결한 시편에 비하여 색이 검게 변하였으며, 장시간 소결시 시편 표면에 조대 입자의 생성 및 입계 이완이 관찰되었다. 이에따라 수소분위기 하에서 장시간 소결된 시편의 경우 냉각 시 상전이가 일어나 다량의 단사정상이 상온에서 존재하였다. 저온 aging동안 등온상전이 속도는 산소분위기에서 소결한 시편보다 수소분위기에서 소결한 시편에서 낮게 나타났으며, 이러한 경향은 $Y_{2}$O$_{3}$의 고용량이 크고, 입자크기가 적은 시편일수록 증가하였다. 또한 2Y-TZP 시편에서는 입자크기에 상관없이 대부분의 정방정상이 단사정상으로 빨리 등온상전이를 일으켰으나, 3Y-TZP 시편의 경우, 등온상전이는 입자크기가 증가함에 따라 상전이 속도도 증가하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.3
• /
• pp.115-119
• /
• 2001

Hydroxyapatite-yttria stabilized zirconia bioceramics containing fine zirconia particles were prepared as 3-layered functionally graded materials (FGMs) using a spark plasma sintering (SPS) and hot pressing (HP) apparatuses. The pretreatment of the raw hydroxyapatite promoted the sinterability of hydroxyapatite. The maximum density of pretreated FGM composites could be obtained at lower temperature than that for he untreated FGM samples. No decomposition from hydroxyapatite to three calcium phosphate (TCP) was observed in FGMs of HAp-$ZrO_2$ sintered below $1200^{\circ}C$ for 8 min under 10 MPa by SPS. However, the transformation of the tetragonal zirconia to the cubic modification had occurred in FGMs at this temperature. The presence of zirconia i.e. stress induced transformation of zirconia may be expected to enhance the mechanical properties of HAp-$ZrO_2$ FGM. The SPS is concluded as a better method to fabricated the FGM with dense and high strength compared with HP process.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.1
• /
• pp.16-20
• /
• 2005

In order to improve electrical conductivity and mechanical properties of 8YSZ SOFC electrolyte material, we used Al₂O₃ as an additive and applied the spark plasma sintering (SPS) method. The sintered bodies were densified above 96 ％ of theoretical density at 1200℃ and possessed microstructures composed of homogeneous grains less than 1 ㎛ in size. The addition of Al₂O₃ improved fracture toughness and bending strength by inhibiting grain growth of 8YSZ and increased total ionic conductivity because grain interior conductivity appeared to remain constant and grain boundary conductivity increased. It was assumed that the dissolution of Al₂O₃ into 8YSZ which was inevitable problem at commercial sintering method was effectively prohibited by the SPS technique with a relatively low sintering temperature and the reaction between Al₂O₃ and SiO₂ present at grain boundary to produce the crystalline Al/sub 2-x/Si/sub l-y/O/sub 5/ phase, resulting in the increase of grain boundary conductivity.

• Journal of Energy Engineering
• /
• v.19 no.2
• /
• pp.73-80
• /
• 2010

A solid oxide fuel cells(SOFC) is a clean energy technology which directly converts chemical energy to electric energy. When the SOFC is used in cogeneration then the efficiency can reach higher than 80%. Also, it has flexibility in using various fuels like natural gases and bio gases, so it has an advantage over polymer electrolyte membrane fuel cells in terms of fuel selection. A typical cathode material of the SOFC in conjunction with yttria stabilized zirconia(YSZ) electrolyte is still Sr-doped $LaMnO_3$(LSM). Recently, application of mixed electronic and ionic conducting perovskites such as Sr-doped $LaCoO_3$(LSCo), $LaFeO_3$(LSF), and $LaFe_{0.8}Co_{0.2}O_3$(LSCF) has drawn much attention because these materials exhibit lower electrode impedance than LSM. However, chemical reaction occurs at the manufacturing temperature of the cathode when these materials directly contact with YSZ. In addition, thermal expansion coefficient(TEC) mismatch with YSZ is also a significant issue. It is important, therefore, to develop cathode materials with good chemical stability and matched TEC with the SOFC electrolyte, as well as with high electrochemical activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.87-87
• /
• 1999

본 연구에서는 Pulsed Laser Deposition(이하 PDL)방법을 이용하여 Si기판에 (Ba,Sr)TiO3(이하 BST)박막을 MFS-FET(Metal-Ferroelectric-Semiconductor Field-effect Transistor)구조로 제조하였으며 BST박막의 강유전성이 BST 박막에 유도되는 응력에 어떤 영향을 받는지 살펴보았다. 본 연구에서는 완충막을 사용함으로써 BST박막과 완충막간의 격자부정합을 이용하여 BST박막에 강유전성을 유도하려고 하였다. 또한 MFS-FET구조의 BST박막에 유도되는 응력조절을 위하여 BST박막과 완충막의 두께를 변화하였으며 XRD를 통한 구조 분석 및 C-V test를 통한 전기적 특성을 관찰을 하였다. PLD법을 통해서 epitaxial 성장된 BST 박막에서는 Si에 epitaxial 성장된 완충막과의 격자부정합에 의한 BST박막내의 자발분극의 발생이 예상된다. 따라서, 본 연구는 강유전체의 자발분극에 의하여 발생되는 C-V 이력현상이 BST박막과 완충막과의 격자부정합에 의한 응력에 의해 발생될 것으로 예상하여, BST 박막에 유도되는 응력과 C-V 이력현상의 관계를 통하여 상온에서 상유전성을 갖는 BST가 응력에 의하여 어느 정도의 강유전성을 나타내는지를 밝히기 위해 진행되었다. 본 연구에서 사용된 완충막은 YSZ(Yttria Stabilized Zirconia)박막으로 0.4mTorrO2 분위기 하에서 600~80$0^{\circ}C$의 온도에서 증착하여 상형성을 살펴보았고 $700^{\circ}C$에서 epitaxial 성장을 확인하였으며 두께는 30~$\AA$으로 변화하였다. 또한 BST박막은 완충막과의 전압분배를 고려해 300~2000$\AA$으로 두께를 변화를 시키며 증착하였다. MFS 구조에서 Al 전극을 사용하여 완충막과 BST박막간의 두께 변화에 따른 Capacitance - Voltage(C-V) 측정을 하였으며 이를 통하여 강유전상의 특성인 C-V 이력현상을 관찰하였다. 그 결과 YSZ 박막에서는 C-V 이력현상이 나타나지 않았으며 BST 박막에서는 약 1.2V의 C-V이력현상이 보였다.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.296-301
• /
• 2023

Solid oxide fuel cell has received more attention recently due to the fuel flexibility via internal reforming. Commonly used Ni/YSZ anode, however, can be easily deactivated by carbon coking in hydrocarbon fuels. The carbon deposition problem can minimize by developing alternative perovskite anode. This study is focused on improving conductivity and catalytic activity of the perovskite anode by introducing rGO (reduced graphene oxide). Sr_0.92Y_0.08TiO₃(SYT) anode with perovskite structure was synthesized with 1wt% of rGO. The presence of rGO during anode fabricating process and cell operation is confirmed through XPS and Raman analysis. The maximum power density of rGO/SYT anode improved to 3 times in H₂ and 6 times in CH₄ comparing to that of SYT anode due to the high electrical conductivity and good catalytic activity for CH₄.