• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.2
• /
• pp.240-253
• /
• 1996

The refrigeration cycle of automobile air-conditioners is simulated in an effort to provide a computational tool for optimum thermodynamic design. In the simulation, thermodynamic and heat transfer analysis was performed for the four major components : evaporator, condenser, compressor, and expansion valve. Effectiveness-NTU method was used for modeling both evaporator and condenser. The evaporator was divied into many subgrids and simultaneous cooling and dehumidifying analysis was performed for each grid to predict the performance accurately. Blance equations were used to model the compressor instead of using the compressor map. The performance of each component was checked against the measured data with CFC-12. Then, all the components were combined to yield the total system performance. Predicted cycle points were compared against the measured data with HFC-134a and the deviation was found to be less than 5% for all data. Finally, the system model was used to predict the performance of CFC-12 and HFC-134a for comparison. The results were very reasonable as compared to the trend deduced from the measured data.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.533-538
• /
• 2013

Silicon carbide (SiC) materials are typical ceramic materials with a wide range of uses due to their high hardness and strength and oxidation resistance. In particular, due to the corrosion resistance of the material against acids and bases including the chemical resistance against ionic gases such as plasma, the application of SiC has been expanded to extreme environments. In the SiC deposition process, where chemical vapor deposition (CVD) technology is used, the reactions between the raw gases containing Si and C sources occur from gas phase to solid phases; thus, the merit of the CVD technology is that it can provide high purity SiC in relatively low temperatures in comparison with other fabrication methods. However, the product yield rarely reaches 50% due to the difficulty in performing uniform and dense deposition. In this study, using a computational fluid dynamics (CFD) simulation, the gas velocity inside the reactor and the concentration change in the gas phase during the SiC CVD manufacturing process are calculated with respect to the gas velocity and rotational speed of the stage where the deposition articles are located.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3164-3170
• /
• 2021

The increasing interest that GEANT4 is gaining nowadays, because of its special capabilities, prompted us to address its reliability in neutronic calculation for the realistic and complex spallation target MEGAPIE of the Paul Scherrer Institute of Switzerland. In this paper we have specifically addressed the neutronic characterization of the active zone of this target. Three physical quantities are evaluated: neutron flux spectra and total neutron fluxes on target's z-axis, and the neutron yield as a function of the target's altitude and radius. Comparison of the obtained results with those of the MCNPX reference code and some experimental measurements have confirmed the impact of the geometrical and proton beam models on the neutron fluxes. It has also allowed to reveal the intrinsic influence of the code type. The resulting differences reach a factor of ~2 for the beam model and 4-18% for the other parameters cumulated. The analysis of the neutron yield has led us to conclude that: 1) Increasing the productivity of the MEGAPIE target cannot be achieved simply by increasing the thickness of the target, if the irradiation parameters are not modified. 2) The size of the spallation area needs to be redefined more precisely.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.650-656
• /
• 2012

The aims of the experiment, conducted over three years in the Central Europe field conditions, were (1) to investigate the effect of growing period (plantings in the middle and at the end of August: $1^{st}$ and $2^{nd}$ term, respectively) on yield and chemical composition of the non-heading Chinese cabbage (Brassica rapa var. chinensis) cultivars 'Taisai', 'Pak Choy White', and 'Green Fortune', and (2) to develop regression models to evaluate the changes in crop yields as a function of weather conditions. A highest marketable yield was obtained from 'Taisai' (65.71 and 77.20 $t{\cdot}ha^{-1}$), especially in the $2^{nd}$ term of production. Low yield, observed for 'Pak Choy White' was due to its premature bolting. Almost 39% ($1^{st}$ term) and 70% ($2^{nd}$ term) of plants of this cultivar formed inflorescence shoots before harvest. The highest dry matter level was observed in the leaf petioles of 'Taisai', while 'Green Fortune' was the most abundant of carotenoids and L-ascorbic acid. The content of soluble sugars was the lowest for 'Pak Choy White'. In a phase of harvest maturity, more of the analyzed constituents were gathered by plants from earlier plantings, and differences were as follows: 4.7% (dry matter), 26.3% (carotenoids) and 22.1% (L-ascorbic acid), in comparison to $2^{nd}$ term of production. Significant increase of soluble sugars level was observed for plants from later harvest. The regression model for marketable yield of Chinese cabbage cultivar 'Taisai' as a function of maximum air temperature can predict the yield with accuracy 68%. The models for yield or bolting of 'Pak Choy White', based on extreme air temperatures and sunshine duration, were more precise (98%). It should be pointed out that Taisai could be recommended for later growing period in Central Europe conditions with regard to maximum yield potential. 'Green Fortune' was notable for its uniform yielding. To obtained plants of higher nutritional value, earlier time of cultivation should be suggested. Described models can be successfully applied for an approximate simulation of Chinese cabbage yielding.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.226-236
• /
• 2013

The heat distribution and internal flow from the efficiency of actual reformer and specification variation, using the computer simulation and experiment about the steam methane reforming reaction which uses the high temperature reformer. Reaction model from steam refoemer uses the steam response model developed by Xu & Froment.As result we supposed the chemical react Steam Reforming(SR), Water Gas Shift(WGS), and Direct Steam Reforming(DSR) from the inner high temperature reformer dominates the response has dissimilar response. According to result of steam methane reforming reaction exam using high temperature reformer, we figured out when Steam Carbon Ratio(SCR) increase, number of hydrogen yield increases but methane decreases. When comparing and examining between design with one inlet and two inlet, result came out one inlet design is more outstanding at thermal distribution and internal flow, hydrogen yield in one inlet design than two inlet design.

• Geomechanics and Engineering
• /
• v.36 no.4
• /
• pp.355-366
• /
• 2024

The original elastoplastic Hardening Soil model is formulated actually partly under hexagonal pyramidal Mohr-Coulomb failure criterion, and can be only used in specific stress paths. It must be completely generalized under Mohr-Coulomb criterion before its usage in engineering practice. A set of generalized constitutive equations under this criterion, including shear and volumetric yield surfaces and hardening laws, is proposed for Hardening Soil model in principal stress space. On the other hand, a Mohr-Coulumb type yield surface in principal stress space comprises six corners and an apex that make singularity for the normal integration approach of constitutive equations. With respect to the isotropic nature of the material, a technique for processing these singularities by means of Koiter's rule, along with a transforming approach between both stress spaces for both stress tensor and consistent stiffness matrix based on spectral decomposition method, is introduced to provide such an approach for developing generalized Hardening Soil model in finite element analysis code ABAQUS. The implemented model is verified in comparison with the results after the original simulations of oedometer and triaxial tests by means of this model, for volumetric and shear hardenings respectively. Results from the simulation of oedometer test show similar shape of primary loading curve to the original one, while maximum vertical strain is a little overestimated for about 0.5% probably due to the selection of relationships for cap parameters. In simulation of triaxial test, the stress-strain and dilation curves are both in very good agreement with the original curves as well as test data.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.1 no.1
• /
• pp.12-19
• /
• 1999

CERES-rice, a rice growth simulation model, was used in conjunction with daily weather data to figure out the spatial variation of the phenology and yields of paddy rice at 168 rice cultivation zone units(CZU) of Kyunggi Province in 1997. Two sets of cultivar specific coefficients, which represent early and mid-season maturing varieties, were derived from field experiments conducted at two crop experiment stations. The minimum data set to run the model for each CZU (daily maximum and minimum temperature, solar irradiance, and rainfall) was obtained by spatial averaging of existing 'Digital Map of Korean Climate'(Shin et al., 1999). Soil characteristics and management information at each CZU were available from the Rural Development Administration. According to a preliminary test using 5 to 9 years field data, trends of the phasic development(heading and physiological maturity), which were obtained from the model adjusted for these coefficients, were in good agreement with the observed data. However, the simulated inter-annual variation was somewhat greater than the reported variation. Rough rice yields of the early maturing cultivar calculated by the model were comparable with the reported data in terms of both absolute value and inter -annual variation. But those of the mid season cultivar showed overestimation. After running the simulation model runs with 1997 weather data for 168 CZU's, rough rice yields of the 168 CZU's calculated by the model were aggregated into corresponding 33 counties by acreage-weighting to facilitate direct comparison with the reported statistics from the Ministry of Agriculture and Forestry. The simulation results were good at 22 out of the 26 counties with reportedly increasing yield trend with respect to the past 9 years average.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.145-154
• /
• 2006

In the companion paper, the composition and structure of the MATDYMO (Multi-Agent for Traffic Simulation with Vehicle Dynamic Model) were proposed. MATDYMO consists of the road management system, the vehicle motion control system, the driver management system, and the integration control system. Among these systems, the road management system and the integration control system were discussed In the companion paper. In this paper, the vehicle motion control system and the driver management system are discussed. The driver management system constructs the driver agent capable of having different driving styles ranging from slow and careful driving to fast and aggressive driving through the yielding index and passing index. According to these indices, the agents pass or yield their lane for other vehicles; the driver management system constructs the vehicle agents capable of representing the physical vehicle itself. A vehicle agent shows its behavior according to its dynamic characteristics. The vehicle agent contains the nonlinear subcomponents of engine, torque converter, automatic transmission, and wheels. The simulation is conducted for an interrupted flow model and its results are verified by comparison with the results from a commercial software, TRANSYT-7F. The interrupted flow model simulation is implemented for three cases. The first case analyzes the agents' behaviors in the interrupted flow model and it confirms that the agent's behavior could characterize the diversity of human behavior and vehicle well through every rule and communication frameworks. The second case analyzes the traffic signals changed at different intervals and as the acceleration rate changed. The third case analyzes the effects of the traffic signals and traffic volume. The results of these analyses showed that the change of the traffic state was closely related with the vehicle acceleration rate, traffic volume, and the traffic signal interval between intersections. These simulations confirmed that MATDYMO can represent the real traffic condition of the interrupted flow model. At the current stage of development, MATDYMO shows great promise and has significant implications on future traffic state forecasting research.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.5
• /
• pp.583-594
• /
• 2003

Ozone is an important atmospheric pollutant that is occurred in tropospheric chemical process and it also affects the human health and plants. For a correct application of abatement strategies for ozone, it is necessary to understand the factors that control atmospheric ozone removal by dry deposition processes. The present study investigates the numerical simulation of the dry deposition velocity (V$^{d}$ ) obtained from PNU/DEM (Pusan National University Deposition Model). PNU/DEM includes seasonal categories, meteorological factors, surface properties and land-use types and proposes for an accurate numerical computation. And, this study examines the ability of the PNU/DEM to compute V$_{d}$ of ozone over water surfaces and evaluates PNU/DEM by comparing its estimated V$_{d}$ to past observed V$_{d}$ over water. The parametrization was found to yield V$_{d}$ values generally in good agreement with the observations for the deciduous forest and the coniferous forest. Ozone is removed slowly at wet surface or water due to its low water solubility. Therefore V$_{d}$ values over water were lower than Vd values over the other surfaces. Comparison of PNU/DEM simulated V d values to observations of ozone V$_{d}$ that have been reported in the literature implies that PNU/DEM produces realistic results.

• Wind and Structures
• /
• v.14 no.1
• /
• pp.15-34
• /
• 2011

Three wind-tunnel simulations of the atmospheric boundary layer (ABL) flow in suburban country exposure were generated for length scale factors 1:400, 1:250 and 1:220 to investigate scale effects in wind-tunnel simulations of the suburban ABL, to address recommended wind characteristics for suburban exposures reported in international standards, and to test redesigned experimental hardware. Investigated parameters are mean velocity, turbulence intensity, turbulent Reynolds shear stress, integral length scale of turbulence and power spectral density of velocity fluctuations. Experimental results indicate it is possible to reproduce suburban natural winds in the wind tunnel at different length scales without significant influence of the simulation length scale on airflow characteristics. However, in the wind tunnel it was not possible to reproduce two characteristic phenomena observed in full-scale: dependence of integral length scales on reference wind velocity and a linear increase in integral length scales with height. Furthermore, in international standards there is a considerable scatter of recommended values for suburban wind characteristics. In particular, recommended integral length scales in ESDU 85020 (1985) are significantly larger than in other international standards. Truncated vortex generators applied in this study proved to be successful in part-depth suburban ABL wind-tunnel simulation that yield a novel methodology in studies on wind effects on structures and air pollution dispersion.