• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.193-201
• /
• 2002

The development of railway vehicle and bogie involves the proper selection of design parameters not only to achieve high speed but also to reduce the vibration of the train. In this study an analytical model of a high speed freight car is developed to find the critical speed. The high speed freight car can generate the snake motion of the lateral and yawing motion of the car body, the bogie, and the wheelset. Numerical analysis for the nonlinear equation motions with 17 degrees of freedom showed the running stability and critical speed due to the snake motion. Also, the vibration modes of tile high speed freight car was calculated using ADAMS RAIL, which showed that the critical speed have the yawing modes of the car body and the bogie. Finally, this paper shows that the snake motion of the vehicle can be controlled with the modifications of the design parameters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.649-654
• /
• 2010

A three-dimensional numerical study of the WIG-effect vehicle with a direct-underside-pressurization (DUP) system and a propeller is performed to analyze the aerodynamic forces and moments acting on the vehicle. The computational model includes all the compartments of a WIG-effect vehicle, including a propeller in the middle of the fuselage and an air chamber under the fuselage. The DUP system and propeller help considerably reduce the take-off speed and minimize the effect of the hump drag when the vehicle accelerates to take off on water. The airflow is accelerated by a propeller, and the air then enters the air chamber through a channel in the middle of the fuselage, this air helps increase the lift since the dynamic pressure of air is converted to static pressure. However, the air accelerated by the propeller produces excessive drag and creates yawing moment. It is found that the effect of yawing and rolling moments on static stability is negligible.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.71-76
• /
• 2008

In this study, side force, drag, and the yawing moment were measured based on the angle of attack by using two models of different nose shapes with slender bodies, which were general shapes in the subsonic area. As a result, the side force and yawing moment were the highest at a specific angle of attack. The boundary between asymmetrical normal state and asymmetrical abnormal state were able to be seen. As a result of analyzing the side force, drag, and yawing moment by time, reliability varied depending on the shape of the head at the same angle of attack. The results of measuring pressure distribution from the surface of the slender body at each angle of attack were as follows: as the angle of attack gets higher, the distribution of surface pressure was asymmetrical.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.5
• /
• pp.487-495
• /
• 2012

The yaw control, a major part of the wind turbine, is closely related to the efficiency of electric power production and the mechanical load. The yaw error, which results from the nacelle not being appropriately aligned in the wind direction, not only decreases the power output but also reduces the lifetime of the wind turbine as a result of large fatigue loads. However, the yawing rate cannot be increased indefinitely because of constraints on mechanical loads. This paper investigates the characteristics of an active yaw control system, the basic principle of the system, and mechanical loads around the yaw axis during yawing.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.2
• /
• pp.301-308
• /
• 2017

This paper proposes a disturbance observer based controller design method for generating and yawing control of windturbine with two cooperative generators. Windturbine system with two cooperative generators is a distinct structure in which the wind energy supplied by blade axis is converted into electrical energy by two cooperative generators. In this structure, two generators can be controlled independently and therefore they can generate power, simultaneously performing yawing control of nacelle without extra yawing mechanism by cooperatively controlling generating load in appropriate manner. Using this structural trait, this paper designs a disturbance observer based controller that enables the windturbine system with cooperative generators to generate and yaw stably, and verifies the performance of the controller experimentally by applying it to a small-scale windturbine system with the same structure.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.1
• /
• pp.81-89
• /
• 2012

Commonly used horizontal-axis wind turbines (HAWT) have the following structure: two or three blades, a nacelle which contains power converting equipments, generators, and a tower which supports the nacelle. The generated power is transmitted from the nacelle to the ground. Due to this structure, the power transmission lines are twisted when the nacelle is yawing. Thus, slip ring or additional yaw control mechanism is required. We propose a new structure of HAWT which is free of this transmission line problem. Moreover, the size of inverter can be reduced since two generators are connected in parallel in our mechanism so that power is distributed. A controller for yawing is developed so that it works in harmony with the controller for power generation. A MPPT (Maximum Power Point tracking) algorithm is implemented for the proposed system and efficiency of the system is validated by simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.2
• /
• pp.241-249
• /
• 2008

In this study, lateral vibration analysis has been conducted on a propulsion and lift shafting system for an air cushion vehicle using ANSYS code. The shafting system is totally flexible multi-elements system including air propeller, aluminum alloy of lift fan and thin walled shaft with flexible coupling. The analysis included the lateral natural frequencies, mode shapes and harmonic analysis of the shafting system taking into account three-dimensional models for propulsion and lifting shaft system. In case of ACV the yawing and pitching rate of craft will be quite high. During yawing and pitching of craft significant gyroscopic moment will be applied to the shafting and will generate high amplitude of lateral vibration. So, such a shafting system has very intricate lateral vibrating characteristics and natural frequencies of shafting must be avoided in the range of operating revolution. The control of lateral vibration is included in this study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.478-485
• /
• 2015

Availability of the climbing angle information is crucial for the intelligent vehicle system. However, the climbing angle information can't be measured with the sensor mounted on the vehicle. In this paper, climbing angle estimation system is proposed. First, longitudinal acceleration obtained from gyro-sensor is compared with the actual longitudinal acceleration of the vehicle. If the vehicle is in yawing motion, actual longitudinal acceleration can't be approximated from time derivative of wheel speed, because lateral velocity and yaw rate affect actual longitudinal acceleration. Wheel speed and yaw rate can be obtained from the sensors mounted on the vehicle, but lateral velocity can't be measured from the sensor. Therefore, lateral velocity is estimated using unknown input observer with nonlinear tire model. Simulation results show that the compensated results using lateral velocity and yaw rate show better performance than uncompensated results.

• Nuclear Engineering and Technology
• /
• v.52 no.8
• /
• pp.1669-1676
• /
• 2020

The IAEA held the IAEA Robotics Challenge 2017 (IRC2017) to protect workers during inspections of spent nuclear fuel and to improve work efficiency and accuracy rates. To this end, we developed an unmanned surface vehicle (USV) system called the spent fuel check vehicle (SCV). The SCV extracts and tracks the target through image processing, and it is necessary to find suitable parameters for the SNF storage environment in advance. This preliminary work takes time. It is also difficult to prepare the environment in which the work will proceed. In addition, if the preliminary work does not proceed as planned, the system will not move at the proper speed and will become unstable, with yawing and overshoot. To solve this problem, we developed a controller with a camera that can extract the depth at which the target is stored and allow distance-adaptive control. This controller is able to attenuate system instability factors such as yawing and overshoot better than existing controllers by continuously changing system operation parameters according to the depth. In addition, the time required for preliminary work during inspections can be shortened.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.65-69
• /
• 2002

In order to practicalize high precision centerless grinder for machining the ferrule, its feeding system is designed and tested. For satisfying the desired diametric tolerance and cylindricity of the ferrule, the feeding system is designed to have relatively high axial stiffness of 600 N/$\mu\textrm{m}$, high angular motion accuracy of 0.5 arcsec/mm in yaw direction and minimum resolution of 0.05 $\mu\textrm{m}$. A prototype of feeding system is built up with hydrostatic guideway and ballscrew. A linear scale with 0.05 $\mu\textrm{m}$ of resolution is used for position feedback. Experimental results show that the feeding system has the infinity of axial stiffness within the range of 1000 N and 0.3 arcsec/mm of yawing error. Also the feeding system shows obvious step response against 0.05 $\mu\textrm{m}$/step command without the lost motion or backlash. Although the vertical stiffness is reduced to 440 N/$\mu\textrm{m}$ by the elastic deformation of rail, it is good enough to use for machining the ferrule. From above, it is confirmed that the feeding system is applicable to centerless grinder for machining the ferrule.