• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.937-942
• /
• 2007

A new, systematic, simplified design procedure for quasi-Yagi antennas is presented. The design is based on the simple impedance matching among antenna components: i.e., transition, feed, and antenna. This new antenna design is possible due to the newly developed ultra-wideband transition. As design examples, wideband quasi-Yagi antennas are successfully designed and implemented in Ku- and Ka-bands with frequency bandwidths of 53.2% and 29.1%, and antenna gains of $4{\sim}5 dBi$ and $ 5{\sim}5.6 dBi$, respectively. The design method can be applied to other balanced antennas and their arrays.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.4
• /
• pp.28-34
• /
• 1975

텔레비젼 수신용 안테나로써 가장 널리 사용되고있는 Yagi안테나는 구조가 간단하고 지향성 이득등이 좋으나 방사주파수에 대한 반파장길이의 소자를 사용하므로 칫수가 커지고 주파수대역이 좁다. 따라서 설치 취급등에 불편을 느낄 경우가 많다. 한편 최근 일반적으로 아무곳에서나 용이하계 설치할 수 있을만큼 소형이면서 화질이 좋은 수상이 가능한 수신안테나에 대한 요망이 커지고 있는데 본 연구에서는 그 파장에 비해서 소형인 폴디드·다이폴 안테나 소자 2개를 좁은 간격으로 배열하고 이들을 이상결합하므로써 VHF텔레비젼전파의 고채널 주파수대에서 비교적 양한 단일지향성을 얻고 있다. 본 안테나에 능동소자를 이용한 저잡음광대역증폭기를 삽입한다면 다소자 Yagi안테나에 비나될 전후방비를 갖는위에 그의 이득도 크게 증가되어 일반수상안테나로 뿐만 아니라 고우스트 방지용실내안테나로서 상당한 기여틀 할것으로 생각된다. The Yagi antenna, which is most widely used for television receiving, has simple form and good directiyity as well as high gain, but it must be made with linear elements of half wave length. Therefore, the dimension of multi-element Yagi antenna becomes bulky and so a(ten it is inconvenient to install and handle, because of its big size. Moreover the frequency band width of the Yagi antenna is usually not broad enough to cover the total frequency range of VHF TV channels in our country. Recently, the aemand for an antenna which is not only small enough to install it easily anywhere but also assures good quality of pictures is generally increasing. In this study 2 elements o( folded dipole, which is small compared to its electrical ways length, are fixed parallel to each other with a narrow distance and the emfs induced in them are made to get together with some phase difference. This new phased array antenna has shown a relatively good unidirectivity through over the high channel VHF television frequency hand as well as the good PIB ratio which is comparable to that of multielements Yagi antenna. As a result this new antenna will be used as a VHF high channel TV receiving antenna and it may become better antighost antenna when used inside the room than other room antennas.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.57-58
• /
• 2018

In this paper, we studied a design method for a quasi-Yagi antenna operating over a broad bandwidth covering the UHF RFID(902-928 MHz) and GNSS(1,164-1.605 MHz). The proposed antenna is composed of three elements(dipole, reflector, and director) and fed by a coplanar waveguide. To reduce its size, a balun is integrated inside the antenna, and the ends of both the dipole and reflector are bent. Broadband impedance matching was obtained by placing the director near to the dipole and loading a chip capacitor inside the antenna. The antenna, designed through simulations, was fabricated on an FR4 substrate with 0.8 mm thickness. The experiment results for the antenna characteristics agree very well with the simulation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4515-4521
• /
• 2010

A Yagi antenna, which is a typical directional antenna, has been designed and fabricated as a surveillance sensor. The proposed Yagi antenna satisfies the requirements as a surveillance sensor; impedance bandwidth of 7.2-8.2GHz, maximum gain of 7dBi, and 3dB beamwidth of $60^{\circ}$ in the azimuthal plane. The proposed Yagi antenna is designed with 3 directors and one driven element on a dielectric substrate. Also, a microstrip-to-CPS balun is designed and applied to the proposed antenna for balanced feeding of the dirven element. The performance of the proposed antenna has been verified by comparing the simulation and measurement results.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.227-233
• /
• 2011

This paper describes the development of a broadband quasi-Yagi antenna using a folded dipole driver. The antenna is designed on a low-permittivity substrate to reduce the surface wave effect, and hence the gain can be enhanced easily by adding directors. The folded dipole driver is connected to a 50-${\Omega}$ microstripline via a simple broadband microstrip-to-coplanar stripline transition with a quarter radial stub. The key motivation for the use of a folded dipole is to increase the input impedance at the driver, allowing a smaller mismatch loss between the antenna driver and the coplanar stripline feed. The proposed antenna has a measured bandwidth of 4.67~6.26 GHz for the -10 dB reflection coefficient, and a flat gain of 4.86~5.15 dB within the bandwidth.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.1
• /
• pp.45-52
• /
• 2009

In this paper, a new rectenna is presented for the wireless transmission of microwave power using dipole antenna (Quasi Yagi effect) and rectifier of CPS resonator structure. The dipole antenna with CPW feedline has high peak gain than a general dipole antenna. A ground plane of CPW is used to reflect a dipole as a Yagi antenna. Therefore, the new rectenna receives the RF power better than the one using general dipole. A RF-to-DC conversion efficiency of 61 % using a 1.4 $k{\Omega}$ load resistor is obtained at 5.8 GHz.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.436-441
• /
• 2018

In this paper, a design method for a compact double dipole quasi-Yagi antenna with a V-shaped ground plane operating in dual bands including 2.45 GHz and 5 GHz wireless LAN frequency bands is studied. First, a quasi-Yagi antenna operating in the 2.45 GHz band is designed, and a V-shaped ground plane is used instead of a conventional strip ground plane to reduce the length of the antenna. A second dipole is connected to the dipole driver of the quasi-Yagi antenna for 2.45 GHz band and a director is appended for 5 GHz band operation. A prototype of the proposed dual-band antenna operating at 2.45 GHz WLAN band and 4.57-7.11 GHz band is fabricated on an FR4 substrate with a dimension of 40 mm by 55 mm. Fabricated antenna shows frequency bands of 2.33-2.75 GHz and 4.38-7.5 GHz for a voltage standing wave ratio less than 2. Measured gain remains more than 4 dBi in both bands.

• Journal of Advanced Navigation Technology
• /
• v.28 no.2
• /
• pp.232-237
• /
• 2024

In this paper, a broadband double dipole quasi-Yagi antenna using a 4×2 meander line array structure for maintaining 8 dBi gain was studied. The 4×2 meanderline array structure consists of a unit cell in the shape of a meanderline conductor, and it was placed above the second dipole antenna of the double dipole quasi-Yagi antenna. A double dipole quasi-Yagi antenna with generally used multiple strip directors was designed on an FR4 substrate with the same size, and the input reflection coefficient and gain characteristics were compared. Comparison results showed that the impedance frequency bandwidth increased by 6.3% compared to when using the multiple strip directors, the frequency bandwidth with a gain of 8 dBi or more increased by 10.1%, and average gain also slightly increased. The frequency band of the fabricated antenna for a voltage standing wave ratio less than 2 was 1.548-2.846 GHz(59.1%), and gain was measured to be more than 8 dBi in the 1.6-2.8 GHz band.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.63-64
• /
• 2017

In this paper, we studied a design method for a coplanar waveguide-fed compact quasi-Yagi antenna for a dual band of the UHF RFID (915 MHz) and GPS (1.575 GHz). The proposed antenna is composed of three elements of a dipole, a reflector, and a director. To reduce its size, the ends of both the dipole and reflector are bent, the director is placed near to the dipole, and a balun is incorporated in the antenna. From some simulations, the proposed antenna using an FR4 substrate with 0.8 mm thickness was designed for the operations in the UHF RFID and GPS systems, and the antenna characteristics such as reflection coefficient, gain, and radiation patterns were examined.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.13-19
• /
• 2004

This paper demonstrates the detailed study of a microstrip Yagi-Uda antenna with and without PBG structure at wireless LAN(5725∼5825 MHz) frequency band. The impedance bandwidth of the antenna with the PBG holes is greater than (about 30 MHz) that of its counter part without PBG holes. The measured gains of the antenna at the frequency band are 7 dB and 6 dB respectively for antenna with and without PBG. The improvement of gain of about 1 dB is likely due to the suppression of surface wave.