• Progress in Superconductivity
• /
• v.6 no.2
• /
• pp.99-103
• /
• 2005

For ac applications a detailed understanding of the ac power losses associated with different conductor configurations is of crucial importance. YBCO thin films were divided into parallel filaments with widths of 1, 2, and 4 mm to reduce hysteresis losses. The measured hysteresis losses show a linear relationship between the strip width and hysteresis loss as anticipated. The influence of different inter-filament separations on the hysteresis loss is investigated.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.7
• /
• pp.315-319
• /
• 2003

We improved quench properties of a superconducting fault current limiter (SFCL) based on YBCO thin films by their serial and parallel combinations. The SFCL consisted of 6 switching elements fabricated of 4 inch-diameter YBCO thin films. The quench currents of the switching elements were distributed between 33.9 A and 35.6 A. Simple serial connection resulted in imbalanced power dissipation between switching elements even at the quench current difference of 0.6 A. On the other hand, $2{\times}2$ and $3{\times}2$ stack combinations produced simultaneous quenches. The $3{\times}2$ stack combination showed better simultaneous quench behavior than the $2{\times}2$ stacks. This is suggested to be because the currents between switching elements in parallel connection of the $3{\times}2$ stacks were more effectively redistributed than the $2{\times}2$ stacks.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.16-19
• /
• 2003

YBCO film을 이용하여 2 stripe-meander 형태의 초전도 한류기를 제작하고 시험하였다. 초전도 film의 hot spot에 의해 발생하는 열을 분산시키기 위해 gold shunt layer를 입혔다. 사고각 $0^{\circ}$에서 사고발생 후 최초 quench 전류값은 $9.56A_{peak}$이었고 약 0.63 msec동안 fast quench 가 진행되고 이후에는 gold층의 열발생에 의한 저항증가가 약 3주기동안 진행된 후 안정되었다. 사고각 $45^{\circ}$와 $90^{\circ}$ 에서는 전류가 상승하는 도중 혹은 최고지점에서 사고가 발생했기 때문에 fast quench time이 각각 0.56 msec와 0.26msec를 보였다. 초전도 한류기를 적용하였을 때 사고전류는 사고직후 약 5배, 3주기후에는 약 8.5배까지 효과적으로 제한함을 알 수 있었다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.24-26
• /
• 2003

We fabricated Ni and Ni alloy substrates for YBCO coated conductors. The Ni and Ni alloy substrate was fabricated by powder metallurgy technique and cold rolling. The texture of substrates had a strong 4-fold symmetry and ［111］∥ND texture after annealing temperature of 100$0^{\circ}C$. The measured full-width half-maximum (FWHM) of in-plane and out-of-plane was in the range of 6$^{\circ}$-10$^{\circ}$. The powder metallurgy technique is fabrication of the substrates for considered to be suitable for the application of YBCO coated conductors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.93-94
• /
• 2006

The $I_c$ degradation behavior of YBCO CC tapes due to torsional deformation has been investigated. Particularly, the influence of torsion angle on the $I_c$ in HTS tapes was examined at 77K (self-field). At low torsional angles or shear strains, the $I_c$ degradation was small and gradual. Also, a good consistency of the $I_c$ degradation behaviors was found along the longitudinal direction under torsion when multiple voltage terminals were adopted for investigating the homogeneity of the $I_c$ degradation.

• Superconductivity and Cryogenics
• /
• v.1 no.2
• /
• pp.14-20
• /
• 1999

초전도 재료는 선재의 형태로 가공하면 송전선이나 변압기, 발전기 그리고 전력 저장장치 등에 사용되어 전력계통의 효율을 극대화시킬 수 있는 재료로서 실제 응용 기기의 개발을 위해 많은 연구가 수행되고 있다. 더우기 1980년대 후반에 개발된 고온초전도 산화물 재료는 액체질수의 비등점인 77K 이상에서 초전도현상을 나타내어 초전도 현상의 응용에 대한 기대를 고조시켜 이에 대한 연구를 더욱 활성화시키고 있다. 초전도선재 연구는 그간 PIT(Powder in Tube) 공정을 이용한 Ag/Bi-2223(Ag/$Bi_2Sr_2Ca_2Cu_3O$) 선재가 높은 전기적 성질과 장선 가공상의 잇점으로 인해 많은 연구와 성과가 있었다. 그러나 Ag/Bi-2223선재는 강한 자기장 하에서 통전 능력이 현저하게 저하되는 성질 때문에 높은 자기장하에서 사용하기 위해서는 사용온도를 액체질소온도보다 상당히 낮은 20K 부근까지 낮추어야 한다는 점 때문에 전력기기 개발에 제한이 따르는 단점이 있다. 이에 반해 최근에 개발된 금속/YBCO 박막 복합선재는 높은 전기적 특성 이외에 특히 높은 자장에서도 통전 능력의 저하가 적어 제한 없이 전력기기의 모든 분야에 사용할 수 있는 특징이 있다. 따라서 1993년에 일본에서 Ni 금속기판에 물리적 증착방법으로 YBCO($YiBa_2Cu_3O$) 박막을 증착시킨 선재제조에 성공하고 있어 1996년에 Oak Ridge National Laboratories (ORNL)에서 Rolling Assisted Biaxially Textured Substrate (RaBiTS) 라는 집합조직을 형성시킨 금속기판이 개발되어 연속적인 가공의 가능성이 확인된 후 이의 특성향상 및 가공기술 개발을 위한 많은 연구가 수행되고 이다. 이 글에서는 이제 까지 개발된 금속기판을 사용한 YBCO계 초전도 박막형 선재의 제조기술 중에서 최근 가장 가능성 있는 것으로 평가되는 RABiTS 방법을 위주로 그 외에 IBAD와 ISD 방법에 관하여 소개하고 현재까지의 개발현황 및 앞으로의 전망에 대하여 간략하게 기술하고자 한다.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.796-798
• /
• 2002

In these days, the interruption capability of some circuit breakers, which are installed in the transmission systems, is getting lower than the magnitude of the fault current because of continuous increase of power demand and relatively short power line which was installed in forms of mesh network As a result of these situations, fault current limiters (FCLs) are strongly necessary. There are various types which is investigated around the world, and new power apparatuses that have been newly considered and developed by many manufactures. In this paper, we considered resistive superconducting fault current limiters with YBCO thin films. The resistive limiters utilize a transition of YBCO films from superconducting to normal state caused by exceeding the critical current. By means of newly occurred impedance, the fault current will be limited effectively. Generally, a few current path patterns are available for YBCO films to enhance the current limiting performance of YBCO films. In this paper. the meander-type and the bi-spiral-type were used for current paths of YBCO flims. When YBCO films are quenched into the normal state, bubbles could be observed on the surface of YBCO films. Using our high-speed camera, the number of bubbles and the size of bubbles could be visualized and the relation between bubbles and current density was analyzed. By means of moving pictures of bubbles, we observed how the quench extended or how the heat was conducted in films.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.392-396
• /
• 1999

Superconducting YBa$_2Cu_3O_{7-{\delta}}$(YBCO) thin films were grown on Hastelloy(Ni-Cr-Mo alloys) with CeO$_2$ buffer layer in-situ by pulsed laser deposition in a multi-target processing chamber. To apply superconducting property on power transmission line, we have deposited YBCO thin film on flexible metallic substrate. However, it is difficult to grow the YBCO films on flexible metallic substrates due to both interdiffusion problem between metallic substrate and superconducting overlayers and non-crystallization of YBCO on amorphous substrate. It is necessary to use a buffer layer to overcome the difficulties. We have chosen CeO$_2$ as a buffer layer which has cubic structure of 5.41 ${\AA}$ lattice parameter and only 0.2% of lattice mismatch with 3.82 ${\AA}$ of a-axis lattice parameter of YBCO on [110] direction of CeO$_2$ In order to enhance the crystallization of YBCO films on metallic substrates, we deposited CeO$_2$ buffer layers with varying temperature and 02 pressure. By XRD, it is observed that dominated film orientation is strongly depending on the deposition temperature of CeO$_2$ layer. The dominated orientation of CeO$_2$ buffer layer is changed from (200) to(111) by increasing the deposition temperature and this transition affects the crystallization of YBCO superconducting film on CeO$_2$ buffered Hastelloy.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.114-119
• /
• 2006

High critical current density, high n value, multiple faults endurances, and fast recovery characteristics of YBCO thin films are very attractive characteristics for developing resistive type superconducting fault current limiters. But due to the limited current and voltage ratings of one YBCO module, it is needed to construct series and parallel module connections for high capacity electric networks. Especially for distribution network, more than 30 units should be connected in series to meet voltage level. So in order to construct distribution-level superconducting fault current limiter, simultaneous quench in one YBCO thin films should be realized, and furthermore, quench should be occurred in all fault current limiting units equally to avoid local heating and failures. In this paper, we proposed optimum design of YBCO thin films for fault current limiting module and technical method using shunt resistor to achieve simultaneous quench between multi current limiting units. From the analytical and the experimental results, optimal current path and thickness of shunt material was determined for YBCO thin films and shunt resistor between modules was developed. Finally, 14 kV one phase resistive fault current limiter using multi YBCO thin films was constructed and it was possible to get satisfactory test results.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.329-331
• /
• 1995

Laser ablation was used to fabricate superconducting $YBa_2Cu_3O_{7-x}$ (YBCO) thin films on metallic substrates with an YSZ buffer layer. An ArF excimer laser with an wavelength of 193 nm was used to deposit both YSZ buffer layer and superconducting thin film. The characterizations of thin films were performed and compared. With a 200 nm YSZ buffer layer, c-axis orientation and $T_c$=85 K were obtained for a 200 nm-thick YBCO film.