• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.319-321
• /
• 1999

To solve the problems in the present ree1-to-reel deposition method, we have developed a new deposition system for a 12m long YBCO coated conductor. The system comprises two chambers, a reaction chamber and a evaporation chamber which are connected through window. A tan long fi tape textured by RABiTS was wound around a cylinderical sample holder of 20cm diameter. The cylinder was rotated in the reaction chamber during deposition of YBCO film by coevaporation. We'll describe the details of the performance of this system as well as the RABiTS process for a 12m long Ni tape.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권2호
• /
• pp.50-53
• /
• 2015

The properties of High Temperature Superconducting (HTS) tapes are progressing, as HTS tapes evolve from 1st generation to 2nd generation. This paper presents design and construction of a 2nd generation HTS magnet consisting of two nested GdBCO and YBCO pancake coils. Two HTS tapes of different widths were used to wind the HTS nested magnet. Considering that a higher magnetic field is applied to the inner magnet than to the outer magnet, 12 mm GdBCO tape was used for winding the inner magnet, which consisted of four single pancake windings. Eight double pancake windings wound with 4.4 mm YBCO tapes were used for the outer magnet. The test results show that the central magnetic field of the HTS nested magnet was 920 mT. The measured critical currents of the inner and outer magnet at 77K were 80.8 A and 32.6 A, respectively.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권9호
• /
• pp.584-589
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on a 2-inch diameter Al2O3 substrate. The current limiting element was 1 mm wide and 260mm long meander line prepared by standard photolithography. The minimum quench current of the current limiting element was about 8 Apeak. This SFCL sucessfully controlled the fault current below 14.3 Apeak at the voltage of 100 Apeak which is otherwise to increase up to 141 Apeak. The quench completion time was less than 3 msec. The temperature of the current limiting element rose to about 200 K in 3 cycles after fault. The SFCL showed reproducible quench during hundreds times of repeated experiments.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.313-320
• /
• 1996

We have fabricated an in-plane aligned a-axis oriented YBa2Cu3O7-x (a-YBCO) thin film on a LaSrGaO4(100) substrate with a PrBa2Cu3O7-x(PBCO) template layer by two step plused laser deposition using 308 nm XeCl excimer laser. A YBCO layer and PBCO layer grown at low temperatures were used as template layers. We have investigated the effect of the deposition temperature of template layers on the superconducting and struc-tural properties of in-plane aligned a-YBCO thin films. An optimal deposition temperature of the PBCO template layers was 630. In-plane aligned a-YBCO thin films showed an anisotropy ratio in resistivity of 11.5 and a zero resistance temperature of 88 K.

• Progress in Superconductivity
• /
• 제6권2호
• /
• pp.99-103
• /
• 2005

For ac applications a detailed understanding of the ac power losses associated with different conductor configurations is of crucial importance. YBCO thin films were divided into parallel filaments with widths of 1, 2, and 4 mm to reduce hysteresis losses. The measured hysteresis losses show a linear relationship between the strip width and hysteresis loss as anticipated. The influence of different inter-filament separations on the hysteresis loss is investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.288-290
• /
• 1997

Pulsed laser ablation has been used to fabricate superconducting $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The epitaxial YBCO thin films were grown at $750^{\circ}C$ and oxygen partial pressure of 200 mTorr. The electrical property and the characteristics of the YBCO thin films have been studied by R-T measurement. scanning electron microscopy (SEM) and X-ray diffraction (XRD). A microstrip line resonator has been fabricated using YBCO superconducting thin films by photolithography and wet-etch process. The resonator has linear microstrip line separated by a gap of 0.278 mm. We observed a fundamental resonance peak at the frequency of 10.007 GHz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.633-634
• /
• 2008

본 논문에서는 안정화 층이 없는 YBCO CC(Coated Conductor)의 YBCO층을 임의의 수로 분할한 경우에 대하여 전기적인 특성을 알아보기 위해 각 소선의 임계전류 값을 측정하는 방법을 제안하였다. 안정화 층이 없음으로 통전 중 주울 열에 의한 선재의 소손을 막기 위해 전류를 펄스파 형태로 인가하여 측정하였으며, 선형적으로 전류를 인가하는 측정 방법에 의한 결과와 비교하였다. 결과적으로 안정화층이 없는 경우의 전기적 특성 측정을 위해서는 본 논문에서 제안한 방법이 우수함을 보였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.635-636
• /
• 2008

현재 고온 2세대 YBCO CC(Coated Conductor) 초전도 선재를 사용하여 초전도 전력기기를 제작하게 되면 BSCCO 선재보다 많은 전류를 인가할 수 있지만, 자화 손실도 더 많이 발생하게 된다. 본 논문에서는 폭 12 mm YBCO CC선재를 이용하여 자화 손실을 줄일 수 있는 몇 개의 샘플을 제작하고, 먼저 각 샘플에 대해 외부에서 수직으로 (${\theta}=90^{\circ}$) 가해지는 자장 값에 대한 자화 손실을 측정하였다. 그 후에 측정값을 이용하여 임의 방향으로 가해지는 자장 값들에 대한 자화 손실을 계산하고, 측정한 값과 비교하여 자화 손실의 패턴을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.673-674
• /
• 2008

팬케이크 형태로 권선된 고온초전도 마그넷의 경우 모든 팬케이크 권선을 직렬로 연결하여 단일전원으로 여자할 경우 가장 큰 수직자장을 받는 팬케이크 권선에 의해 모든 팬케이크 권선의 임계전류가 제한된다. 본 논문에서는 별도전원으로 여자되는 YBCO 고온초전도 마그넷의 특성을 계산하여 단일전원으로 여자되는 경우와 비교하였다. 계산 결과 별도전원으로 여자되는 YBCO 고온초전도 마그넷의 모든 팬케이크 권선들은 각각의 임계전류까지 통전되었으며 중심자장의 세기가 단일전원으로 여자되는 마그넷보다 증가함을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.129-132
• /
• 1996

Surface modification like cone formation on Pulsed laser deposition (PLD) occurs in YBCO target surface irradiated by laser beam. Cone formation results in a reduction of deposition rate, so that it is significant obstacles to an efficient deposition process. With the change of various conditions such as the number of laser shot, target density, direction of incoming laser beam, we have systematically analyzed the modification of target surface. Because cones formed by beam-target interactions grow in direction of incoming laser beam, we have used the method of rotating the target position by 180$^{\circ}$ with the same number and position of laser shot. Experimental results of losing the directionality and changing the shape of cones formed on laser irradiated YBCO target surface is obtained by the SEM image. Also, we have observed that the size of cones formed on target by pulsed laser became larger with increasing the number of laser shots.