• Progress in Medical Physics
• /
• v.23 no.2
• /
• pp.114-122
• /
• 2012

For the determination of absorbed dose to water from a linear accelerator photon beams, it needs a exposure calibration factor $N_x$ or air kerma calibration factor $N_k$ of air ionization chamber. We used the exposure calibration factor $N_x$ to find the absorbed dose calibration factors of water in a reference source through the TG-21 and TRS-277 protocol. TG-21 used for determine the absorbed dose in accuracy, but it required complex calculations including the chamber dependent factors. The authors obtained the absorbed dose calibration factor $N_{dw}{^{Co-60}}$ for reduce the complex calculations with unknown $N_{dw}$ only with $N_x$ or $N_k$ calibration factor in a TM31010 (S/N 1055, 1057) ionization chambers. The results showed the uncertainty of calculated $N_{dw}$ of IC-15 which was known the $N_x$ and $N_{dw}$ is within -0.6% in TG-21, but 1.0% in TRS-277. and TM31010 was compared the $N_{dw}$ of SSDL to that of PSDL as shown the 0.4%, -2.8% uncertainty, respectively. The authors experimented with good agreement the calculated $N_{dw}$ is reliable for cross check the discrepancy of the calibration factor with unknown that of TM31010 and IC-15 chamber.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.673-680
• /
• 2003

This study verified the relationship between fracture mechanics parameters(ΔK, ΔK$\sub$eff/, K$\sub$max/) and X-ray parameters (${\alpha}$$\sub$r/, B) for SG365 steel at elevated temperature up to 300$^{\circ}C$. The fatigue crack propagation test were carried out and X-ray diffraction technique according to crack length direction was applied to fatigue fractured surface. The residual stress on the fracture surface was found to increase low ΔK region, reach to a maximum value at a certain value of K$\sub$max/ or ΔK and then decrease. Residual stress were independent on stress ratio by arrangement of ΔK and half value breadth were independent by the arrangement of K$\sub$max/. The equation of ${\alpha}$$\sub$r/ - ΔK was established by the experimental data. Therefore, tincture mechanics parameters could be estimated by the measurement of X-ray parameters.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.226-229
• /
• 2014

In this study, lead-free $(Ba_{0.85}Ca_{0.15})(Ti_{1-x}Zr_x)O_3$ ceramics and a bimorph-type piezoelectric actuator were fabricated using the normal oxide-mixed sintering method, and their dielectric properties, microstructure, and displacement properties were investigated. From the results of X-ray diffraction, the pattern of the specimen has a pure perovskite structure. In addition, no secondary impurity phases were found. The excellent piezoelectric coefficient of $d_{33}=454pC/N$, the electromechanical coupling factor $k_p=0.51$, the dielectric constant ${\varepsilon}_r=3,657$, the mechanical quality factor $Q_m=239$, and $T_c$(Tetragonal-Cubic) =$90^{\circ}C$ were shown at x= 0.085. ${\Delta}k_p/k_p20^{\circ}C$ and ${\Delta}f_r/f_r20^{\circ}C$ showed the maximum value of -0.255 and 0.111 at $-20^{\circ}C$ and $80^{\circ}C$, respectively. The maximum total-displacement was $60{\mu}m$ under the input voltage of 50 V. As a result, it is considered that lead-free $(Ba_{0.85}Ca_{0.15})(Ti_{1-x}Zr_x)O_3$ ceramics is a promising candidate for piezoelectric actuator application for x= 0.085.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.317-323
• /
• 2001

This study verified the relationship between fracture mechanics parameters$({\Delta}K,\;{\Delta}K_{eff},\;K_{max})$ and X-ray parameters $(\sigma_r,\;B)$ for SG365 steel at elevated temperature up to $300^{\circ}C$. The fatigue crack propagation test were carried out and X-ray diffraction technique according to crack length direction was applied to fatigue fractured surface. The residual stress on the fracture surface was found to increase low ${\Delta}K$ region, reach to a maximum value at a certain value of $K_{max}\;or\;{\Delta}K$ and then decrease. Residual stress were independent on stress ratio by arrangement of ${\Delta}K$ and half value breadth were independent by the arrangement of $K_{max}$. The equation of $\sigma_r-{\Delta}K$ was established by the experimental data. Therefore, fracture mechanics parameters could be estimated by the measurement of X-ray parameters.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.117-123
• /
• 2002

X-ray diffraction observation of fracture surfaces yields useful information to analyze the causes of failure accidents of engineering structures. This experimental technique, named X-ray fractography, has been developed especially in metal and mechanical engineering fields. The distributions of the residual stress and the half value breadth of diffraction profiles beneath the fatigue fracture surface were measured with SNCM 439, HT100 and Ti-6Al-4V alloy. The size of the maximum plastic zone was successfully determined on the basis of the measured distributions. This size was correlated to maximum stress intensity factor. The distributions of the half value breadth of diffraction profiles on the fatigue fracture surfaces were measured with SNCM 439. HT100. The equations of x-ray parameter distribution were possible to estimated fracture parameters of fatigue fracture surfaces.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.7
• /
• pp.709-715
• /
• 2001

We have been studied photosensitization mechanism's additive effect, of perylene 3,4,9,10-tetracarboxyl-diimide and X-phthalocyanine (charge generation materials), using the photochemical and photoelectrochemical approach. It was found that the photoreceptor on the excited state reacts with metal oxide, which creates the charge transfer on the interface of SnO2/electrolyte. In the electrode (X5P1) made of five X-phthalocyanine and single perylene 3,4,9,10-tetracarboxyldiimide layers, the cathodic photocurrent of X-phthalocyanine in the 400-600 nm region was increased by the addition of perylene 3,4,9,10-tetracarboxyldiimide. The maximum wavelength of fluorescence of perylene 3,4,9,10-tetracarboxyldiimide showed no dependence on the temperature. The addition of 4-dibenzylamino-2-methylbenzaldehyde diphenylhydrazone known as charge transport material was represented as decreasing photocurrent for X-phthalocyanine and perylene 3,4,9,10-tetracarboxyldiimide, respectively. In the electrode (X1P1) made of single X-phthalocyanine and single perylene 3,4,9,10-tetracarboxyldiimide layers, an anodic photocurrent of about 10.5 nA was generated by addition of hydroquinone at 550 nm. And the characteristic of photoinduced discharge was shown to decrease by a factor of 5 and the speed of dark decay was increased by a factor of 1.2.

• Nuclear Engineering and Technology
• /
• v.56 no.5
• /
• pp.1822-1829
• /
• 2024

The search for materials that serve as good shields for radiation has become very important in light of the increasing exposure to ionizing radiation in various vital sectors. The aim is to search for novel materials with better radiation shielding properties that are stable, nontoxic, and abundant and environment friendly. The solidstate reaction approach has been used to synthesize a few ceramics, including BaZr_XTi_1-XO₃, Ba_1-XLa_XTiO₃ and Ba_1-XLa_XZr_XTi_1-XO₃ (with x = 0.10) i.eBaZr_0.10Ti_0.90O₃ (BZT), Ba_0.90La_0.10TiO₃ (BLT), and Ba_0.90La_0.10Zr_0.10Ti_0.90O₃ (BLZT). The density of the prepared samples varies from 6.3471 to 11.6003 g/cm³. The X-ray diffraction technique, shows strong peaks to confirm the crystalline structure of prepared ceramic samples. Using the G-P fitting approach, the advanced radiation shielding parameters (build-up factor) have been evaluated in the photon energy region of 1.5 keV-15 MeV. It is observed from the results that exposure buildup factor (EBF) and energy absorption buildup factor (EABF) are maximum for BLZT and has the minimum value for BZT in the entire photon energy regime. The results of this work should be useful in radiation shielding applications such as in industry, medicine, and nuclear engineering.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.356-360
• /
• 2017

We investigated the phase evolution, microstructure, and microwave dielectric properties of Na- and Zr-doped $Ba(Mg_{0.5}W_{0.5})O_3$ [i.e., ($Ba_{1-2x}Na_{2x})(Mg_{0.5-x}Zr_xW_{0.5})O_3$] ceramics. $BaWO_4$ as a secondary phase was observed in all compositions, and it increased as the dopant concentration increased. All specimens revealed a dense microstructure. For the composition of x=0.01, polyhedral grains were observed. As the dopant concentration increased, the densification and the grain growth were promoted by a liquid phase. The quality factor($Q{\times}f_0$) decreased remarkably, whereas the dielectric constant (${\varepsilon}_r$) tended to decrease as the dopant concentration increased. The dielectric constant, quality factor, and temperature coefficient of the resonant frequency of the composition of x=0.01 sintered at $1,700^{\circ}C$ for 1 h were 18.6, 216,275 GHz, and $-22.0ppm/^{\circ}C$, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.7
• /
• pp.344-348
• /
• 2006

The effect of x on microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics for microwave components were investigated. All spcecimens prepared by the conventional mixed oxied method and sintered at $1450^{\circ}C$. Microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-xTiO_2$ ceramics were influenced by $MgTi_2O_5$ phase. Also the microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics were dominated with an addition of $CaTiO_3\;and\;SrTiO_3$. The dielectric constant $(\varepsilon_r)$, quality factor $(Q{\times}f_r)$ and temperature coefficient of the resonant frequency $(TCRF,\;\tau_f)$ of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics were $12.96\sim70.98,\;5,132\sim186,410GHZ$ and $-35.82\sim+75.96ppm/^{\circ}C$, respectively, and depend on x and addition materials.

• Journal of Animal Science and Technology
• /
• v.63 no.5
• /
• pp.977-983
• /
• 2021

Closely correlated expression patterns between ubiquitin specific peptidase 9X-linked (USP9X) and adherens junction formation factor (Afadin) in mouse testis development suggests that Usp9x regulates the deubiquitination of Af-6 (also known as Afadin, AFDN), and subsequently, the cell adhesion dynamics during gametogenesis. However, this relationship has not yet been tested in other domestic animals. The study was examined the temporal and spatial expression patterns of porcine USP9X and AFDN from the pre-pubertal to adult stages using real time-PCR and immunohistochemistry. Furthermore, we detected the transcripts of USP9X and AFDN in the testis of 1-, 6- and 12-months old boar, respectively. USP9X and AFDN were found to have similar expressions patterns, with basal expression after 1 month followed by a significant up-regulation from 6 months (puberty) onwards. In addition, neither the AFDN or USP9X proteins were detected in spermatogenic cells but they were expressed in the leydig cells and sertoli cells. USP9X was detected around the basal lamina during pre-puberty, and predominantly expressed in the leydig cells at puberty. Finally, in adult testis, USP9X was increased at the sertoli cell-cell interface and the sertoli cell-spermatid interface. In summary, closely correlated expression patterns between USP9X and AFDN in boar testis supports the previous findings in mice. Furthermore, the junction connections between the sertoli cells may be regulated by the ubiquitination process mediated via USP9X.