• 한국소음진동공학회논문집
• /
• 제21권12호
• /
• pp.1185-1191
• /
• 2011

The kinematic characteristics of cutting device significantly affects cutting performance in 2-dimensional elliptical vibration cutting(EVC) where the cutting tool cuts workpiece, traversing a micro-scale elliptical trajectory in a trochoidal motion. In this study, kinematical characteristics of EVC device constructed with two parallel stacked piezoelectric actuators were analytically modeled and compared with the experimental results. The EVC device was subjected to step and low-frequency(0.1 Hz) sinusoidal inputs to reveal only its kinematical displacement characteristics. Hysteresis in the motion of the device was observed in the thrust direction and distinctive skew of the major axis of the elliptical trajectory of the cutting tool was also noticed. Discrepancy in the voltage-to-displacement characteristics of the piezoelectric actuators was found to largely contribute to the skew of the major axis of the elliptical trajectory of the cutting tool. Analytical kinematical model predicted the cutting direction displacement within 10 % error in magnitude with no phase error, but in estimating the thrust direction displacement, it showed a $27^{\circ}$ of phase-lag compared with the measured displacement with no magnitude error.

• 한국생산제조학회지
• /
• 제25권4호
• /
• pp.295-300
• /
• 2016

In the design of passive and active boring bars, the structural dimensions and shape of the vibration control boring bar are modified depending on the diameter and depth of the workpiece, which changes the dynamic behavior. Thus, the natural frequency, effective mass, and stiffness for the main structure of a tube-type boring bar need to be reset for each vibration control case. However, commercial finite element method (FEM) software and experimental modal analysis are mostly used at present despite being too time-consuming. To overcome the weaknesses of the two methods currently used for vibration control, we realized a graphical user interface (GUI) program for the modal analysis of a modified tube-type damping structure. The analysis results with the GUI program were compared to those with commercial FEM software in order to confirm the effectiveness of the former.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.623-628
• /
• 2011

마이크로 방전가공은 활용도가 높은 미세가공기술이지만 가공깊이가 증가하면 방전가공 시에 발생하는 가공부산물인 데브리(debris)로 인해 공구 전극과 공작물이 단락되어 방전의 진행이 힘들고 극심한 전극마모가 발생한다. 이를 극복하기 위하여 공구 전극이나 공작물에 진동을 부가하는 진동 플러싱 기술이 개발되었으나 기존의 진동 플러싱 연구는 피에조 액츄에이터를 적용하여 높은 진동수를 발생시키는 것에만 집중하였다. 본 연구에서는 경제적이면서도 유사한 효과를 얻을 수 있는 솔레노이드를 이용한 진동 플러싱을 제안한다. 솔레노이드를 이용한 진동 플러싱은 피에조 액츄에이터를 이용하는 것에 비해 큰 진폭을 얻을 수 있으며 진동수에 대해 독립적으로 설정하는 것이 용이하다. 가공 실험을 통해 솔레노이드를 이용하여 낮은 진동 주파수에서 큰 진폭으로 진동 플러싱하는 방법이 고주파진동 플러싱과 비교하여 경제적이며 충분한 적용효과를 발휘할 수 있음을 확인하였다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권4호
• /
• pp.24-30
• /
• 2002

In grinding operations, one of the most important problems is to increase efficiency of process. In order to achieve this purpose, it is necessary to administer the tool lift of grinding wheel and to optimize grinding conditions. Frequently dressing result in lowering the process efficiency remarkably and makes production cost high. On the other hand, grinding with a worn wheel causes the workpiece surface roughness to increase and often results in the occurrence of such troubles as chatter vibration and homing.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.11-18
• /
• 1998

In grinding operations, one of the most important problems is to increase efficiency of process. In order to achive this purpose, it is necessary to administer the tool life of grinding wheel and to optimize grinding conditions. Frequently dressing result in lowering the process efficiency remarkably and makes production cost high. On the other hand, grinding with a worn wheel causes the workpiece surface roughness to increase and often results in the occurrence of such troubles as chatter vibration and burning.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.203-208
• /
• 2002

This paper deals with turning experiments of aluminium alloy using a single crystal diamond with round cutting edge. A face cutting was conducted using a special precision machine to study the characteristic phenomena in heavy cutting of aluminium alloy. In many cases, one of the most important matter on the surface integrity is about a damaged layer remaining just under the surface after machining. A machined surface roughness can be improved at a small geometrical surface roughness under special cutting conditions, even if a steady vibration exists between a tool and a workpiece.

• Advances in materials Research
• /
• 제9권3호
• /
• pp.189-202
• /
• 2020

The objective of the present work is to investigate the effect of cutting parameters (Vc, fz and ap) on tool life and the level of vibrations velocity in the machined part during face milling operation of hardened AISI 52100 steel. Dry-face milling has been achieved in the annealed (28 HRc) and quenched (55 HRc) conditions using multi-layer coating micro-grain carbide inserts. Statistical analysis based on the Response surface methodology (RSM) and ANOVA analysis have been conducted through a plan of experiments methodology using a reduced Taguchi table (L9) in order to obtain engineering models for tool life and vibration velocity in the workpiece for both heat treatment conditions. The results show that the cutting speed has a dominant influence on tool life for both soft and hard part. Cutting speed and feed per tooth is the most significant parameters for vibration levels. Comparing the experimental values with those predicted by the developed engineering models of tool life and levels of vibrations velocity, a good correlation has been obtained (between 97% and 99%) in annealed and hard conditions.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1681-1688
• /
• 2000

A dynamic model for the prediction of surface topography in high speed end milling process is developed. In this model the effect of tool runout, tool deflection and spindle vibration were taken in to account. An equivalent diameter of end mill is obtained by finite element method and tool deflection experiment. A modal parameter of machine tool is extracted by using frequency response function. The tool deflection, spindle vibration chip thickness and cutting force were calculated in dynamic cutting condition. The tooth pass is calculated at the current angular position for each point of contact between the tool and the workpiece. The new dynamic model for surface predition are compared with several investigated model. It is shown that new dynamic model is more effective to predict surface topography than other suggested models. In high speed end milling, the tool vibration has more effect on surface topography than the tool deflection.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.121-126
• /
• 2013

Precision machine tools for high dignity cutting are needed for efforts to improve machining accuracy. However, there are many factors to improve machining accuracy. This study investigated how machining accuracy changes when variation and unbalance amount in rotational speed domain is decreased. Machining accuracy of initial machine tools depends on manufacturing and assembly of parts such as bearing. And then, vibration and noise vary with volume of unbalance amount when it is rotation, so it effects unbalance amount. Also vibration and noise increased by unbalance shorten spindle's life and it especially makes worse boring accuracy. Therefore, this study studied the change of roundness and cylindricity of workpiece when it decreases variation and unbalance in rotational speed domain.

• 대한기계학회논문집
• /
• 제1권2호
• /
• pp.89-94
• /
• 1977

So far, high accuracy in-process sensors have been used for controlling the cutting tool, but the method followed in this new system is guite different form previous processes. In this system, after the rough cut the mark indication the pasition of the finished size in put on the cutting surface of the workpiece by ultrasonic or vibration cutting. The cutting is then continued until the mark just disappears, This position being observed by the used of a simple in-proces sensor, The in-prosess sensor in used only to detect the existence or dis apperance of the mark.