• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.3
• /
• pp.307-311
• /
• 2004

The objective of this work is to evaluate the hypothesis that a good technique for supplying oxygen to the saturated zone in the presence of light nonaqueous phase liquid (LNAPL) pool contamination at the water table is to pass air through the unsaturated zone above the pool. This hypothesis was evaluated in experimental studies performed using a bench-scale, sand-tank reactor, Steady-state abiotic experiments in the sand-tank reactor with air flowing through the reactor headspace demonstrated that oxygen supply through the water table interface into the saturated zone was enhanced when an LNAPL (dodecane) pool was present at the water table. These experimental results confirmed the hypothesis that an LNAPL pool can serve as a high concentration oxygen source to the oxygen-limited area beneath the pool and, as a result, enhance the in situ biodegradation rate.

• Journal of Navigation and Port Research
• /
• v.36 no.9
• /
• pp.699-706
• /
• 2012

This paper describes Declination interpolation method in the application of Digital Magnetic Compass(DMC) with small capacity memory for relatively low-priced system. The purpose of this study is to find accurate declination values using Declination Lookup Table(DLT) and Secular Variation Table(SVT) with the Bilinear interpolation method having four points data only. World Magnetic Model with Gauss coefficients produced by NOAA is used in the calculation of DLT and SVT at desired years. To verify the applicability of the proposed method, the simulation tests and the error analysis are carried out in this work. As results from tests, the interpolation error is within 0.01 degree that is much enough to implement high accurate DMC comparing with commercial DMCs on the market. In summary, the declination interpolation method, proposed in this study, can be useful in the application of DMC.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.10
• /
• pp.4007-4024
• /
• 2020

It is tremendously important to construct decision trees to use as a tool for knowledge representation from a given decision table. However, the usual algorithms may split the decision table based on each value, which is not efficient for numerical attributes. The methodology of this paper is to split the given decision table into binary groups as like the CART algorithm, that uses binary split to work for both categorical and numerical attributes. The difference is that it uses split for each attribute established by the directed acyclic graph in a dynamic programming fashion whereas, the CART uses binary split among all considered attributes in a greedy fashion. The aim of this paper is to study the effect of binary splits in comparison with each value splits when building the decision trees. Such effect can be studied by comparing the number of nodes, local and global misclassification rate among the constructed decision trees based on three proposed algorithms.

• Wind and Structures
• /
• v.8 no.3
• /
• pp.213-233
• /
• 2005

Wind uplift rating of roofing systems is based on standardized test methods. Roof specimens are placed in an apparatus with a specified table size (length and width) then subjected to the required wind load cycle. Currently, there is no consensus on the table size to be used by these testing protocols in spite of the fact that the table size plays a significant role in wind uplift performance. Part I of this paper presented a study with the objective to investigate the impact of table size on the performance of roofing systems. To achieve this purpose, extensive numerical experiments using the finite element method have been conducted and benchmarked with results obtained from the experimental work. The present contribution is a continuation of the previous research and can be divided into two parts: (1) Undertake additional numerical simulations for wider membranes that were not addressed in the previous works. Due to the advancement in membrane technology, wider membranes are now available in the market and are used in commercial roofing practice as it reduces installation cost and (2) Formulate a logical step to combine and generalize over 400 numerical tests and experiments on various roofing configurations and develop correction factors such that it can be of practical use to determine the wind uplift resistance of roofs.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.225-227
• /
• 2005

The in-core neutron Flux Mapping System in a pressurized water reactor yields information on the neutron flux distribution in the reactor core at selected core locations by means of movable detectors. The obtained data are used to verify the reactor core design parameters. The detector cables run through guide tubes(thimbles), and typically thirty-six to fifty-eight thimbles are allocated in the reactor depending on the number of fuel assemblies. These thimbles are inserted into nuclear fuel assemblies through conduits connected from the bottom of the reactor vessel to a seal table. During the plant refueling outage period, the thimbles are withdrawn up to 4m from the seal table, the height of a nuclear fuel. In spite of their importance, however, the thimble handling work has been performed by only human operators. In addition, its efficiency is very low due to narrow working environments on the seal table, thereby resulting in the excessive radiation exposure of maintenance personnel. To solve these problems, a new thimble handling equipment for in-core flux mapping system was developed, and we confirmed its effectiveness through experiments.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.640-648
• /
• 2009

Recently the truction of coastal reclaimation work has been extensively implemented in Korea. The Sondo New City is being established on the reclaimed land from the sea, construction companies of metro construction are planing to pull-out the sheet pile for saving the construction cost. In the case of soft marine clay, it is very difficult to pull-out the sheet pile by using the hydraulic hammer difficult. Therefore, the man of the field must be aware of vibration effect to the ground and the structure. For understanding the vibration effect to the ground during subway construction, the model was formulated with 1/25 braced-cut for subway construction. Scott and Iai(1989) proposed the law of the similarity for other experimental conditions. The laboratory model test was conducted under the vibration condition of sheet pile pulling out. The settlement on the ground surface was measured during the shaking table test. The pore water pressure was also monitored in the upper, middle, and lower layers of soil. The field settlement level and the pore water pressure can be predicted by using the results of the laboratory shaking table test.

• Journal of the Korean Professional Engineers Association
• /
• v.16 no.3
• /
• pp.33-40
• /
• 1983

This paper is one of the case studies to improve the labor productivity of PCB assembly through Work Factor motion-time analysis and the application of the motion economy principles and the human factors engineering theory. In result, we can improve 129％ of the labor productivity by using a rotary table for the parts delivery. Therefore, it is expected that this result can be used for a lot of the manual works of the small and medium-sized industries especially.

• Journal of International Academy of Physical Therapy Research
• /
• v.3 no.2
• /
• pp.469-474
• /
• 2012

The purpose of this study is to analyze the correlation between the stature and the muscle performance ratings and the subjective discomfort rations at performing lower arm's pronation and supination according to change sin the height of working table for more efficient performance at designing a working table and performing a work. For the purpose, this study conducted an experiment targeting 40 people in their 20s, who were classified into 4 groups each group composing 10 people at intervals of 5cm from the standard stature of 166.5cm. The experiment measured the maximum isometric pronation and the supination muscular power, and at measuring the factors, the heights of working tables were set as 800mm, 850mm, and 900mm. From the measurement results, it was found that the stature and the maximum muscular power was correlated. That is, as the experiment groups's average stature is higher, the maximum muscular power was higher. For the correlation between the motion patterns(pronation and supination) and the maximum muscular power, it was seen that the maximum muscular power was higher at performing the pronation than the supination. In the correlation between motion patterns and the subjective discomfort ratings, it was seen that the subjective discomfort rating was higher at performing the supination than the pronation. For the correlation between height adjustment and the subjective discomfort ratings, as the height of working table was lower, the subject discomfort rating was lower. Therefore there was no difference in the maximum muscular power according to the height changes of working table, but it was found that as the working table was higher, the user felt more comfortable.

• Korean Journal of Construction Engineering and Management
• /
• v.11 no.3
• /
• pp.125-133
• /
• 2010

Although work-efficiency of construction machinery is a critical factor for estimating its workable-quantity perunit time, the efficiency figure table presented in the Poom-Sam that is used for Construction Cost Estimation of public sectors in Korea is very subjective for practical usage. In order to suggest objective work-efficiency table for a Pump-Dredger, domestic and overseas documentary records were investigated and on-going construction sites were also visited. Moreover, actual work quantities collected from the site visits were compared with the ones calculated based on the Standard Measurement Methods used in Japan. The research found that the table can be revised by means of detailing down by several factors, namely project type, depth of soil, undersea-site shape, and condition on the sea for better estimation of its workable-quantity. The research will be the foundation for applying the rapid development of Construction Equipment and technology to the appropriate cost estimations and the ground work of related studies.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.8 no.1
• /
• pp.36-49
• /
• 1998

The purpose of this study is to investigate the relationship between the work postures and upper extremity cumulative trauma disorders(CTDs) in female medical insurance bill reviewers(n=448). This study included diagnosis for CTDs, anthropometry and job analysis (workstations and posture). The characteristics of subject were 33.6 years of average age and 8.7 years of average work duration. The results were as fallows. Ergonomic conditions of workstation were unsuitable compared with anthropometry result. The height of work surface(79.5 cm) and chair(43.0 cm)were high. work space was small, and legs space under the table was limited. Work postures were awkward compared with recommended neutral postures. Neck flexion($21.0-36.0^{\circ}$), elbow elevation, shoulder abduction ($46.0-47.0^{\circ}$). wrist radial and ulnar deviation, forearm supination and pronation, and wrist repeated motion(12.7-21.5 freq./min) were analyzed as hazardous risk factors by job analysis. The prevalence of CTDs was 32.8 % by medical diagnosis. The prevalence rate of CTDs in hazardous work posture group was significantly greater than safe work posture group both neck-shoulder (relative prevalence = 5.2, p<0.001) and wrist-hand (relative prevalence = 2.5, p<0.05).