• 소성∙가공
• /
• 제21권1호
• /
• pp.58-66
• /
• 2012

The work roll surface temperature rises and falls repetitively during hot slab rolling because the work roll surface is cooled continuously by water. This study focused on Std. No. 7 to determine a cooling method which significantly reduces the tangential tensile stresses on the work roll surface of the hot slab mill at Hyundai Steel Co. in Korea. A series of finite element analyses were performed to compute the temperature distribution and the tensile stresses in the circumferential direction of the work roll. The virtual slab model was used to reduce the run time considerably by assigning a high temperature to the virtual slab. Except for the heat generated by plastic deformation, this is equivalent to the hot rolling condition that a high temperature slab (material) would experience when in contact with the work rolls. Results showed that when the virtual slab model was coupled with FE analysis, the run time was found to be reduced from 2000 hours to 70 hours. When the work roll surface cooled with a certain on-off patter of water spray, the magnitude of the tangential stresses on the work rolls were decreased by 54.1%, in comparison with those cooled by continuous water spraying. Savings of up to 83.3% in water usage are possible if the proposed water cooling method is adopted.

• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.34-43
• /
• 1994

In order to improve thickness profile of cold rolled steel strip, a computer simulation and actual cold rolling experiments on a 4-high tandem cold mill were carried out. In this study, tapered barrel end at top work roll and incurved barrel body at bottom work roll were examined for reducing edge drop and threading of stripe. Also, the most effective stand of tandem cold mill and magnitude of optimal taper crown at several stand were investigated under a typical rolling condition. From actual rolling experiments, it was verified that thickness deviation over strip width could be improved up to 1.06% by applying tapered and incurved work roll only at the second and up to 0.89% by applying them at both the second and the third stand.

• KSTLE International Journal
• /
• 제2권2호
• /
• pp.133-137
• /
• 2001

This paper investigates the correlation between strip surface roughness and the surface of the work roll. As the actual temper mill(TM) is used, this data will be adopted to another actual temper mill for the application and operation of this experiment. Conclusions are as follows: Electro-discharge texturing(EDT) roll has homogeneous roughness distribution and shape, and also a sinuous peak surface and the life is 2 times longer than that of shot blast texturing(SBT) method. And the higher surface roughness of work roll, the more time is necessary at the EDT method. In the SBT method without the correlation of roughness, but impeller rotation speed with an uncontrollable peak count. The roughness of SBT roll is irregularity compared to that of EDT roll because the work roll roughness is transferred to the strip which was temper rolled, and produces a more desirable image and greater clarity to the color painted steel sheet.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.160-163
• /
• 2003

For the purpose of rolling hard metals such as silicon steel and non-ferrous metals, the backup roll driven-type mill has been widely used in cold rolling industry. Since the backup roll drive results in horizontal bending of the work rolls and therefore exerted reciprocal action on the roll gap contour, the selection of slim work rolls is very restricted. In this paper, we present an analytic equation based scheme to determine a proper horizontal position of work roll minimizing the horizontal force subject to mechanical constraints.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.408-417
• /
• 1995

A study on the surface roughness variation of work roll and strip at the temper rolling was performed. The results were obtained with changes according to the surface roughness of work roll and method to make the peak count on the roll in the temper rolling, and factors to affect to the work roll surface in actual rolling machine (ie. Temper mill). The results suggests that the electro-discharge textured roll has mere uniform roughness distribution than shot blasted roll and its life time is two times longer than shot blasted because it has more sine wave roughness, and it is possible to control the Rmax. In shot blasting method, Surface roughness is related to the impeller speed, But it can't control the peak count.

• 대한기계학회논문집
• /
• 제19권5호
• /
• pp.1149-1157
• /
• 1995

The research for variation of coolant film thickness and separating force has been investigated following the examination for friction profile of work roll and roughness change of strip surface in rolling mill producting actual commercial products. The obtained results are as follows ; (1) Coolant film thickness in cold rolling has been increased relative to the circumferential velocity of work roll, and formation of coolant films has decreased with the smaller diameter of work roll. (2) Separating force is related to the formation of coolant film, and large separating force is needed to the formation of coolant film but it is constant after formation of appropriate film. (3) Wear and roughness alleviation of work roll is larger in bottom-roll than in top-roll on cold surface is larger in the direction of width than in roll direction, and changes of roughness and strip surface hardness rarely occurred after 3 passes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.274-278
• /
• 1992

냉간압연기술의 발달로 냉간압연기도 매우 다양하게 발달되었으며 냉간압연의 원자재인 열간압연재의 종류도 다양하다. 최근 열간압연가공시 회수율이 높은 연속주조재(Continuous casting strip)인 CC 재가 종전의 가공과정이 복잡하며 불량율이 높은 Ingot주조재(Ingot casting strip)인 IC 재 보다 생산비율이 점차 증대되어 냉간압연재료의 주종을 차지하고있다. CC재는 냉간압연가공시 IC재에 비해 Work roll 조도저하가 현저하게 크기 때문에 슬립(Slip)과 채팅(Charttering) 현상 등이 발생하여 압연가공성이 불안정 하게 되어 Work roll과 판표면에 손상이 생기게 되고, 압연가공시 Roll 사고 등의 문제가 발생하므로 Roll 마멸의 정도를 파악하여 Roll을 효과적으로 관리하므로써 Work roll과 판표면의 슬립현상 및 채터 링현상 등을 방지할 수 있다.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.80-84
• /
• 2001

The purpose of this paper is to show the result from the study to improve the formability and appearance which is important in the cold rolled strip, the coated strip and prepainted strip. Furthermore, to give appropriate surface roughness, shape of work roll for temper mill is also important. The strip has a greater peak counts and homogeneous roughness. This makes the prepainted surface smooth and consistent in appearance with good image clarity. Therefore, the surface roughness of the work roll is very important. The reason that surface roughness of the work roll is transferred to the strip surface is the rolling farce and tension at the temper rolling or cold rolling. This study is classified in order to get an accurate and homogeneous roughness. There are few papers published in this field, because its importance is not known and the proper operation of the machine is not generally well known. This paper investigates the correlation between strip surface roughness and the surface of the work roll. After studying the surface roughness and shape according to the texturing method for roll surfaces at temper rolling, the findings were as follows. Irregular surface roughness can be compensated with several paint coatings, but this also makes the quality deteriorate and manufacturing costs go up.

• 소성∙가공
• /
• 제6권2호
• /
• pp.161-175
• /
• 1997

The effects of various process paramenters on the detailed aspects of the thermo-mechanical behavior of work roll and on the roll life are investigated via a series of process simulation, using a mathematical model presented previously. The process conditions are discussed that are favorable or optimal in terms of reducing roll wear in the front finishing stands.

• 한국정밀공학회지
• /
• 제8권4호
• /
• pp.33-40
• /
• 1991

The decrease in surface roughness of work roll and steel strip in cold rolling of low carbon steel strip has been investigated by working distance, materials, total separating force and total reduction ratio. The main results are as follows; For the same lubricating conditions. 1) The changing of surface roughness of steel strip were similar to work roll. The transcription ratio is in inverse proportion to the carbon content of steel strip. 2) The surface roughness of steel strip is hardly change according to changing of total separating force and total reduction ration. 3) The wear of work rolls surface is more rapid in that case of continuous casted steel strip than ingot casted steel strip. The aluminium content dull powder adhere on the rolls surface, and so. It makes the mirror surface of work roll accelerate.