• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.615-621
• /
• 2013

The robot calibration has greatly improved the absolute accuracy of the industrial robot. However, the accuracy of the relative positions of robotic tool-tip at work-points on a work-piece is only slightly corrected by the robot calibration since there has been no practical method to eliminate the elements of the setup position errors at a robotic workplace. A robotic workplace calibration is demonstrated in this paper to minimize the relative position errors between a robot tool-tip and the work-point on a work-piece. The existing teaching and playback method has been developed for the robotic workplace calibration. This paper uses the work-piece fixed in a robotic work-place as measurement equipment instead of a special robot measurement equipment for the robotic workplace calibration. The positive effect of the robotic workplace calibration is supported by the results of computer simulation on an ideal robotic workplace model and an experiment at the actual robotic workplace.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.99-107
• /
• 2009

Since a long work piece influences the natural frequency of the entire system with a miniature high speed spindle, a bar-feeder is used for a long work piece to improve the vibration characteristics of a spindle system. Therefore, it is very important to design optimally support positions between a bar-feeder and a long work piece for a miniature high speed spindle system. The goal of the current paper is to present an optimization method for the design of support positions between a bar-feeder and a long work piece. This optimization method is effectively composed of the method of design of experiment (DOE), the artificial neural network (ANN) and the genetic algorithm (GA). First, finite element models which include a high speed spindle, a long work piece and the support conditions of a bar-feeder were generated from the orthogonal array of the DOE method, and then the results of natural vibration analysis using FEM were provided for the learning inputs of the neural network. Finally, the design of bar-feeder support positions was optimized by the genetic algorithm method using the neural network approximations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.184-185
• /
• 2008

Modal analysis is an important and essential process in design of a high speed machining center. Generally, modal analysis of a built-in spindle system has not taken the work piece's shape and dimension into consideration. Since small and long work pieces influence greatly the natural frequency of the entire system, the high speed spindle system which continuously makes small machine parts by long work pieces for improvement of machining time has to consider the machining work pieces. Therefore frequency characteristics of the spindle system with long work pieces are studied in this paper.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.159-166
• /
• 2004

Custom-tailored products are meant by the products having various sizes and shapes to meet the customer's different tastes or needs. Thus fabrication of custom-tailored products inherently involves inefficiency. To minimize this inefficiency, a new paradigm is proposed in this work. In this paradigm, different parts are grouped together according to their sizes and shapes. Then, representative shape of each group is derived and it will be used as the work-piece from which the parts in the group are machined. Once a new product is ordered, the optimal work-piece is selected through making similarity comparisons of new product and each representative shape. Then an effective NC tool-path is generated to machine only the different portions between the work-piece and the ordered product. The efficient machining conditions are also derived from this shape difference. By machining only the different portions between the work-piece and the ordered product, it saves time. Similarity comparison starts with the determination of the closest pose between two shapes in consideration. The closest pose is derived by comparing the ray distances while one shape is virtually rotated with respect to the other. Shape similarity value and overall similarity value calculated from ray distances are used for grouping. A prototype system based on the proposed methodology has been implemented and applied to the grouping and machining of the shoe lasts of various shapes and sizes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.70-73
• /
• 2003

Custom-tailored products are meant by the products having various sizes and shapes to meet the customer's different tastes or needs. Thus fabrication of custom-tailored products inherently involves inefficiency. To minimize this inefficiency, a new paradigm is proposed in this work. In this paradigm. different paris are grouped together according to their sizes and shapes. Then, representative shape of each group is derived and it will be used as the work-piece from which the parts in the group are machined. Once a new product is ordered, the optimal work-piece is selected through making similarity comparisons of new product and each representative shape. Then an effective NC tool-path is generated to machine only the different portions between the work-piece and the ordered product. The efficient machining conditions are also derived from this shape difference. By machining only the different portions between the work-piece and the ordered product, it saves time. Similarity comparison starts with the determination of the closest pose between two shapes in consideration. The closest pose is derived by comparing the ray distances while one shape is virtually rotated with respect to the other. Shape similarity value and overall similarity value calculated from ray distances are used for grouping. A prototype system based on the proposed methodology has been implemented and applied to the grouping and machining of the shoe lasts of various shapes and sizes.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.72-79
• /
• 1997

A study is a experiment which is figure out to optimum discharge cutting condition of the surface roughness, electronic discharging speed and electrode wear ration with Ton , Toff and V(voltage) as an input condition according to the current(Ip) in an electric spark machine : 1) Electrode is utilized Cu and Graphite. 2) Work piece is used the material of carbon steel. The condition of experiment is : 1) Current is varied 0.7(A) to 50(A) and the time of electric discharging to work piece in each time is 30(min) to 60(min). 2) After the upper side of work piece was measured in radius(5$\mu$m) of stylus analyzed the surface roughness to ade the table and graph of Rmax by yielding data. 3) Electro wear ratio is : \circled1Cooper was measured ex-machining and post-machining by the electronic balance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume $\times$specific gravity and analyzed to made its table and graph on ground the data. 4) In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V. R and the memory scope was sticked to the electric spark machine. 5) In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid , it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.130-137
• /
• 1997

The demand for wire-cut EDM is increasing rapidly in the die and tool making industry. In this study machining characteristics such as machining rate, surface roughness, hand drum form and hardness of machined material are investigated experimentally under the conditions varing pulse on time, pulse off time, peak voltage, wire tension after fixing other conditions in SKD 11 and brass and brass workpiece. It was found that various operating conditions had significant influences on machining characteristics. But the hardness of workpiece was uneffected by operating conditions. Also it was obtained experimentally that brass workpeice had better machinability than SKD 11 one.dition according to the current(Ip) in an electric spark machine : 1) Electrode is utilized Cu and Graphite. 2) Work piece is used the material of carbon steel. The condition of experiment is : 1) Current is varied 0.7(A) to 50(A) and the time of electric discharging to work piece in each time is 30(min) to 60(min). 2) After the upper side of work piece was measured in radius(5$\mu$m) of stylus analyzed the surface roughness to ade the table and graph of Rmax by yielding data. 3) Electro wear ratio is : \circled1Cooper was measured ex-machining and post-machining by the electronic balance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume $\times$specific gravity and analyzed to made its table and graph on ground the data. 4) In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V. R and the memory scope was sticked to the electric spark machine. 5) In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid , it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.132-136
• /
• 1996

A Study is a experiment which is figure out to aptimum discharge cutting condition of the surfaceroughness, electric discharging speed and electro wear ratio with Ton Toff and V(voltage) as an input condition according to the current(Ip) in an electric spark machine ; 1)Electrode is utilized Cu(coper) and Graphite. 2)Work piece is used the material of carbon steel. The condition of experiment is; 1)Current is varied 0.7(A) to 50(A). 2)Pulse time(Ton) is varied 3($\mu$s) to 240($\mu$s) and also Toff is varied 7($\mu$s) to 20($\mu$s). 3)The time of electric discharging to work piece in each time is 30(min) to 60(min) 4)After the upper side of work piece was measured in radius (5${\mu}{\textrm}{m}$) of syulus analyzed the surface roughness to made the table and graph of Rmax by yielding data. 5)Electro wear ratio is; \circled1Coper was measured cx-machining and post machining but the electronic baiance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume specific gravity and analyzed to made its table and graph on ground the data 6)In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V.R(Automatic Voltage Regulator). 7)The memory scope was sticked to the electric spark machine. 8)In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid, it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging According to above results, the surface roughness by the variation of electrodw and current was analyzed to compare KS(Korea Standards) It was decided the optimum condition of electric discharge cutting through analyzing the effect of electric discharge speed and electro wear ratio.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.84-91
• /
• 1999

The goal of this study is to analyse the stress and the strain occurring within the work piece at the fine-blanking process and hence to assume the size direction and a distribution chart of the shearing stress as the penetration of the punch is being increased trough the application of the FEM. For this analysis we introduced the piece-wise linear method in the non linear structural analysis program for large deformation sheet metal forming and we defined it as the problem of the non linear contact. Therefore we modeled the above problems as quadratic-nodded axi-symmetrical elements for the character-istics of the work piece. From the result of this analysis it was found that the shearing stress is a great deal occurred on the surface of the work piece during the beginning process of the punch penetration and it's effect is expected to influence importantly for the formation of burnish because the deeper is the penetration of the punch in the narrow clearance zone. the greater is the degree of the strain stress.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.3
• /
• pp.43-50
• /
• 2022

Claude Debussy's is a solo piano piece written in 1894. However, for unknown reasons, the entire piece was not published until 1977, despite clear evidence that Debussy intended to publish it during his lifetime. Interestingly, the second movement of the three pieces comprised in the work was published independently in February 1896 through the Parisian periodical Le Grand Journal. Partly because the work was recently published, it remains relatively more unknown to pianists and music lovers than other piano solo pieces by Debussy. Thus, this article addresses in detail the compositional background of this work, focusing on why the work was not published during Debussy's lifetime. Furthermore, by analyzing this piece in detail, this article intends to discuss the stylistic characteristics of the work regarding its melody, phrase structure, harmony, and form. This survey, which would help understand the musical style embodied in this piece, aims to contribute to improving the awareness of the work.