• 한국가구학회지
• /
• 제18권1호
• /
• pp.20-30
• /
• 2007

This experiment was carried out to investigate the effects of number and location of finger joints on the bending strength of glue-laminated lumbers. Urea resin adhesives were used in this experiment and the resin content was 70% for cold pressing. The lamina were edge-jointed and end-jointed. The specimen were composed of one or three layers. The obtained results are summarized as follows; The effects of finger joints on the decrease of bending strength of glue laminated woods were different according to the number and location of finger joints. The decrease of MOR was highest on the middle position of laminated woods. The effects of several arrangements of finger joints on the bending strength of glue laminated woods showed on Figure 7 and 8. The variance of thickness-laminating on the bending strength of glue laminated woods were larger than those of width-laminating.

• Journal of the Korean Wood Science and Technology
• /
• 제1권2호
• /
• pp.3-10
• /
• 1973

This study was carried out to examine the characeristics of waste sanders(S)from. plywood and pre-finishing plywood surface sanding and double saw finishing, as a new extander in urea-formaldehyde resin(UFR) in plywood adhesive, and to focus, adhesive strength using the glue extended with milled sanders(MS) as extender, leveling the optimum amount of MS to be added, and examining the physical properties of glue extended MS & S. Also economical good feasibility of substitution for wheat flour(WF) with MS as a new extender is analyzed and presented in details. Selecting three standard samples of 80, 100 and 180 mesh, sorking them in distilled water at $20^{\circ}C$, 24 hours, redrying at $105^{\circ}C$ and rescreening the sample with standard screen, again, the 3 samples of 80, 100, and 180 mesh are passed 23 percent through 80 mesh sander standard sample 27 percent through on 100 mesh and only 10.9 percent through 180 mesh, respectively. The particle size of retained parts are greater in size of redried form. It seems undoubtly that particles to be extended in glue are got swollen and become greater in size and coarser in shape. The shape of fresh S particles are irregular thin needle with small scale, as shown in Figure 5. PFS are so finer than plywood S that only 9.8 percent of the S retained on 100 mest screen, 24. 30 percent on 100-160 mesh, and 65.9% on 160-180 mesh. But particle size of the fresh S is large enough to make the viscosity of glue direct extended with S too high to apply it glue spreader. The glue extended with milled sanders(MS). 3 hours milled PFS or 6 hours milled plywood S, having particle sizes shown in Tables 7 and 8, as ratio of Reain/MS/WF/water: 100/8/8/10, indicate good viscosity of 16 to 24 ps, as shown in Figure 5, for applying direct to glue spreader, have high tensile-shear strength (adhesive strength), 102.4 kp/$cm^2$, and 94 percent wood failure.

• Journal of the Korean Wood Science and Technology
• /
• 제32권5호
• /
• pp.59-65
• /
• 2004

물고기의 공기 주머니인 부레를 말려 두었다가 물에 넣어 끓여서 만든 어교는 전통적인 방법으로 사용되고 있다. 어교의 경화시간에 따른 접착력과 접착력을 향상시키기 위한 방법으로 최적의 개방퇴적시간을 조사하여 어교의 접착특성을 연구하였다. TGA, DSC, FT-IR을 이용하여 경화 전과 후의 휘발성 물질(수분)의 변화량에 따른 어교의 경화특성과 어교의 반응성을 측정하였으며 자작나무 시편을 이용한 lap shear strength를 측정하여 경화시간과 개방퇴적시간에 따른 접착특성을 평가 하였다. 본 실험 결과 어교는 경화온도 22±1℃, 상대습도 43±2%에서 경화시간에 따른 접착력은 48시간에서 최대 강도를 나타냈으며 개방퇴적시간과 경화시간에 따른 접착력은 개방퇴적시간을 15분을 유지하고 6시간의 경화시간을 유지할 때 가장 높은 접착력을 나타냈다.

• 보존과학회지
• /
• 제37권6호
• /
• pp.801-806
• /
• 2021

전통 접착 소재인 아교의 사용성과 해초 추출물 카라기난의 겔화 현상을 개선하기 위해 두 재료를 혼합하여 목재 보존용 액상형 접착제를 제조하였으며, 9종의 천연 및 합성 접착제와의 물성 비교를 통해 적용 가능성을 확인하였다. 제조한 목재 접착제는 15 wt% 아교 수용액과 λ-carrageenan, 항균제, 소포제 등을 혼합하였으며, 1.80 Mpa의 최대 접착 강도를 확인하였다. 비교 결과 5종의 전통 천연 접착 성분(수용액)과 Polyvinyl acetate 기반 접착제 1종보다 우수한 접착 강도가 나타났으며, 총호기성생성균수와 유해성(TVOC, HCHO, 중금속) 시험 결과 불검출로 항균성과 안정성을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제23권3호
• /
• pp.33-39
• /
• 1995

To accelerate the cure of phenolic resin adhesives for plywood, the complexation with melamine resin and the addition of cure-accelerating agents were discussed. The hot-pressing temperature and time of phenol resin could be decreased by complexation with melamine resin. but the wet glue-joints strength of phenol melamine resin was lower than that of ordinary phenol resin in case of plywood using spruce veneer at core layer. Among the tested cure-accelerating agents. the sodium carbonate showed the greatest effect on shortening gelation time of phenolic resin. In addition, in the manufacturing scale test, the hot-pressing time of phenol resin with the addition of 5 parts sodium carbonate could be shortened about 20% compared with ordinary phenol resin which had same glue-joints properties.

• Journal of the Korean Wood Science and Technology
• /
• 제3권1호
• /
• pp.16-19
• /
• 1975

• Journal of the Korean Wood Science and Technology
• /
• 제15권4호
• /
• pp.64-68
• /
• 1987

To develope the utilities of the chestnut bur, which is wasted after harvesting chestnut in farmhouses, the feasibilities of adhesion(urea resin) extenders of the powder for plywood were examined. These experiments were implemented on experimental scale at Forestry Research Institute(Seoul) and on a plywood mill scale at Eugon Industrial Co LTD(Inchon) for more reliable data. In this paper, it was proved that the chestnut bur powder caused to rise the glue viscosity but the chaff powder to down reversely. The most effective mixing ratio were wheat flour 5kg, chaff powder: 5kg and chestnut bur powder. 5kg per 100kg of urea resin. At this condition, the viscosity were most appropriate (1,320 2,230 cps) for glue spreading operations, and the dry shear strengthes were most adequate(10.7-13.2kg/$cm^2$), wood failure ratio 82-88%). The chestnut bur powder, can be utilized for plywood adhesion extenders without any change of present process lines in plywwod mills.

• Composites Research
• /
• 제30권4호
• /
• pp.235-240
• /
• 2017

아교는 수용성을 띄는 접착제로, 이 특징에 의해 물에 약하다는 단점에도 불구하고 전통적인 고가구에 많이 사용되어 왔다. 이러한 단점을 개선하기 위하여 많은 연구가 진행되고 있다. 본 연구에서는 탄소나노튜브를 도입에 따른 아교의 계면특성 및 열적특성 그리고 방수특성 개선에 대한 연구를 진행하였다. 탄소나노튜브의 비율이 증가함에 따라 아교를 이용하여 접착한 돌침대용 목재 샌드위치 판 상부의 실시간 온도측정을 진행하였다. 나무와 아교접착제 간의 계면특성의 변화를 알아보기 위하여 랩 전단 실험을 실시하였고, 습도가 높아짐에 따라 물성이 약해지는 아교의 단점을 개선하기 위하여 탄소나노튜브를 도입에 따른 아교의 방수특성이 개선되는지 대한 실험을 진행하였다. 랩 전단시편을 물에 담근 후 랩 전단 실험을 진행하여 기존의 결과와 비교하여 차이가 얼마나 나는지 비교하였다. 이를 증명하기 위하여 물과의 정적 접촉각을 이용해 탄소나노튜브의 함량에 따른 아교접착제의 소수성 정도를 비교하였다. 실험결과 아교 접착제에 탄소나노튜브를 도입으로 계면특성, 열적특성 및 방수특성이 개선되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제47권2호
• /
• pp.239-248
• /
• 2019

This research presents an improvement of the physical and mechanical properties of composite board (com-ply) made of Oriented Strand Board (OSB) coated with wood veneer of Pine (Pinus merkusii), Avocado (Persea Americana) and Mahogany (Swietenia mahogany). 1.5 mm thick veneers of those three wood types were adhered to the surface of OSB using two adhesive types: epoxy and isocyanate. The adhesive with the glue spread of $250g\;m^{-2}$ applied using single glue line was spread and then cold pressed with the pressure of $15kg\;cm^{-2}$ for 3 hours. The research result showed an improving dimension stability of com-ply, but not found on all parameters of physical property test. The moisture content seemed to be influenced by the com-ply type, yet not related to its thickness swelling, water absorption and linear expansion. The exception took place in the parallel linear expansion when immersed for 2 hours. The highest to the lowest increases of MOE and MOR were consecutively found on OSB coated with wood veneer of Pine, Mahogany and Avocado. However, the increases were statistically insignificant. The highest increasing screw hold power was found at the com-ply type AE (avocado veneer and epoxy adhesive) that was by 28%.

• Journal of Applied Biological Chemistry
• /
• 제42권2호
• /
• pp.81-84
• /
• 1999

Blood glue was prepared to reutilize porcine blood. Plasma proteins after lyophilization were treated by addition of wood flour, sodium hydroxide, sodium silicate, and hydrated lime to make blood glue with a suitable adhesivity. Characteristics of the prepared blood glue was monitored by measuring the viscosity with time, and the relationship between degree of hydrolysis of plasma proteins by addition of various amounts of sodium hydroxide and adhesivity was studied. To prevent the emission of formaldehyde during manufacturing of plywood by blood glue, the cross-linking reaction of plasma protein with formaldehyde was also examined. Fourier transform infrared, circular dichroism, and fluorescence spectroscopy study showed that blood plasma proteins react with formaldehyde, resulting in removal of formaldehyde by cross-linking reaction.