• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.572-579
• /
• 2001

본 연구에서는 유한요소해석을 통한 와이어 방전가공기의 설계검증을 위하여 두 모델을 선정하여 CAD 패키지 I-DEAS를 이용하여 3차원 유한 요소모델을 모델링한 후 상용 유한요소해석코드인 ABAQUS로 각 모델의 가공위치에 따른 해석을 수행하였다. JW-35A와 JW-60A 두 모델의 상호 비교 타당성 여부를 확인하기 위하여 ${\eta}-factor$ 개념을 이용하였다. 이어 공리적 설계 개념을 도입하여 오차보정을 위한 설계변수들의 선택과 방법이 적절함을 보이고 두 모델의 유한요소해석 결과를 상호 비교하여 구조물의 설계를 검증하고 변형 예측식을 유도하였다. 본 연구를 통해 유도된 변형 예측식 (5)-(6) 형태의 접근방법은 비단 방전가공기 뿐만 아니라 이와 유사한 형태의 공작기계에도 적용 할 수 있을 것이다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.930-933
• /
• 2001

Titanium Alloys used in this experiment has an good corrosion resistance and specific strength, and is the new material developed for medical supplies living goods. In this study the rolled titanium alloy is done by annealing, solution heat-treatment and aging and then is worked by wire EDM. With changing the process conditions, the process properties of surface hardness, surface roughness, shape of process surface and the analysis of ingredients are measured through experiment repeating main cut and finish cut. It is confirmed to gain good measure values as increasing the number of processing of wire EDM. In this experiment the phenomena of processing is studied and the appropriate process condition is proposed.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.98-105
• /
• 2003

In the experimental study, wire EDM was conducted for cold die steel by changing the Wire electrode, peak discharge current and number of finish cut. From the micro structure analysis of SEM photographs, the size of irregular welded and added component on the EDMed surface is decreasing and size of EDMed plane surface is increasing as the decreasing peak current and increasing number of finish cut. From the analysis of coating effect, Zn component is highly contained in Br and Zn Wire EDMed surface and copper component is highly contained in Br and Al wire EDMed surface. Hardness values are Increasing as the increasing peak current and decreasing the number of finish cut The value of hardness is decreasing as Cu, Al, Zn and Br wire electrode because of the residual austenite effect of solid solution copper on solidification, and finally EDMed surface has the highest hardness values for every wire electrode. Yield strength values becomes larger and bending strength values become smaller due to the increasing the hardness. These results are increased as increasing brittleness with hardness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1044-1048
• /
• 1997

Wire-cut EDM is used in Die manufacturing as the part of non-traditional cutting process, But,the determination of it's cutting condition with high efficiency and precision is difficult due to the influence of cutting environment and cutting mechanism. In this study, we examine the cutting performance of the SKD11 and Brass in wire-cut EDM and make the neural network which have the configuration of 5-12-2 and back-propagation learning rule. Through the neural network, we can appraise the cutting performance before working and determine the optimal cutting condition. By introducing this method to the W-cut EDM, we can enhance the cutting efficiency.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.537-542
• /
• 2000

Wire deflection, surface roughness and roundness were observed on changing discharge time for electrical discharge machining(EDM) of STD-11 in various conditions of thickness. The wire deflection was decreased as increasing discharge time and wire tension. The deflection is the smallest at the speed of wire of 10.6m/min and the water specific resistivity of 5k$\Omega$.cm. The deflection is found to be decreased as increasing dwell time. But if the water pressure is high, it is found not to be changed after the vibration of 4sec. The component of copper(Cu) and zinc(Zn), which is the main material of wire electrode, is observed for rough wire-cutting EDM of STD-11. This phenomena is found to be similar in spite of the change of EDM energy level. But it will be improved by changing the material and the shape of wire. The roundness of middle is found to be worse than that of upper and it is increased as the thickness of material is increased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.820-823
• /
• 2000

The characteristics of wire deflection, surface roughness and roundness were observed on changing discharge time for electrical discharge machining(EDM) of tungsten carbide in various conditions of thickness. The wire deflection was decreased as increasing discharge time and wire tension, the gap of deflection was decreased after thickness 60mm and discharge time of 6$\mu\textrm{s}$ due to the changing from fundamental mode to vibration mode. The deflection is the smallest at the water specific resistivity of 7.5 kΩ ㆍcm. The deflection is found to be decreased as increasing dwell time, and the result is due to the vibration of the pressure and the amount of the dielectric. The component of copper(Cu) and zinc(Zn), which is the main material of wire electrode, was observed for rough wire-cutting EDM of STD-11. This phenomena is found to be decreased as the number of EDM is increased. But it will be improved by changing the material and the shape of wire. The roundness of middle is found to be worse than that of upper and it is increased as the thickness of material is increased.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.64-70
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalt percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (W-EDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rate as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without cracks, 4 finish-cuts were necessary by reducing the electrical energy and the offset value.

• 한국기계가공학회지
• /
• 제4권3호
• /
• pp.5-12
• /
• 2005

In wire discharge machining which is using STD 11 as die materials, the major factors of machining speed are discharge voltage, discharge current, and discharge time. All of the three factors give the effect. Increasing of the discharge pulse time gets groove width wider and it relatively increases surface roughness and clearance. If no load voltage is decreased, surface roughness is good but it decreases machining speed. If on time is increased, machining speed will get faster and clearance and offset value also get bigger.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.130-137
• /
• 1997

The demand for wire-cut EDM is increasing rapidly in the die and tool making industry. In this study machining characteristics such as machining rate, surface roughness, hand drum form and hardness of machined material are investigated experimentally under the conditions varing pulse on time, pulse off time, peak voltage, wire tension after fixing other conditions in SKD 11 and brass and brass workpiece. It was found that various operating conditions had significant influences on machining characteristics. But the hardness of workpiece was uneffected by operating conditions. Also it was obtained experimentally that brass workpeice had better machinability than SKD 11 one.dition according to the current(Ip) in an electric spark machine : 1) Electrode is utilized Cu and Graphite. 2) Work piece is used the material of carbon steel. The condition of experiment is : 1) Current is varied 0.7(A) to 50(A) and the time of electric discharging to work piece in each time is 30(min) to 60(min). 2) After the upper side of work piece was measured in radius(5$\mu$m) of stylus analyzed the surface roughness to ade the table and graph of Rmax by yielding data. 3) Electro wear ratio is : \circled1Cooper was measured ex-machining and post-machining by the electronic balance. \circled2The ex-machining of graphite measured by it, the post-machining was found the data from volume $\times$specific gravity and analyzed to made its table and graph on ground the data. 4) In order to keep the accuracy of voltage affected to the work piece was equipped with the A.V. R and the memory scope was sticked to the electric spark machine. 5) In order to preserve the precision of current, to get rid of the noise occured by internal resistance of electric spark machine and to force injecting for the discharge fluid , it made the fixed table for a work piece to minimize the work error by means of one's failure during the electric discharging.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.90-95
• /
• 2003

The W-EDM is very important In precision machining of die, punch and small parts of precision products, so this machining method is widely used in various fields of industry. In this study, machining characteristics of Hand Drum Form and surface roughness are investigated experimentally. As Hand drum form has great effect on straightness of cut-surface of workpiece, its evaluation is very important in precision cutting. As experimental material, the mold material, STD11 is used and machined by CNC wire-EDM using the 025mm wire in diameter with repeated cutting up to 6 times. The thickness of workpiece is vaned in 20, 40, 60, 80, 100mm Hand drum form and surface roughness are measured after each cutting. Experimental results show that four times-cutting is optimum in the point of hand drum form and surface roughness.