• 한국안전학회지
• /
• 제12권4호
• /
• pp.9-14
• /
• 1997

From the experimental study of wire-cut Electric Discharge Machining for alloyed steel and tungsten carbide, the characteristics such as hand drum form has been observed and evaluated for various conditions. Hand drum form can be improved when gap voltage and spark cycle become smaller, their thickness become thinner, wire tension become larger and number of cutting is done so many times. When wire-cut 60mm thickness tungsten carbide in normal condition, Hand drum form becomes larger due to the low conductivity inducing cobalt composite rising by electrolysis.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.246-251
• /
• 2000

In this paper, Wire electric discharge grinding(WEDG) method for manufacturing the micro shaft was introduced and the machining characteristics was investigated. from the experimental results, it was concluded that high surface integrity could be obtained by use of dielectric fluid spraying method and small capacitive condenser.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.81-88
• /
• 2016

Recently, high-efficiency machining in the production of high-value products with complex shapes has constantly been required along with the need for hybrid machining. In this study, in addition to wire-cut Electric Discharge Machining (EDM) and vibration, we present the possibility of a hybrid process by carrying out an experiment with aluminum alloy, and the hybrid process determines the nature of the surface. The selected experimental parameters are waveform, amplitude, peak current, and two-dimensional (2D) vibration. The experimental results give the guideline for selecting reasonable machining parameters. The surface roughness was improved about 20% with increases in the amplitude of the vibration.

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.22-28
• /
• 1996

From the experimental study of Wire-Cut Electric Discharge Machining of STD-11 alloy steel and P-20 tungsten carbide, the characteristics such as hand drum form and discharge gap have been observed and evaluated for various conditions. Hand drum form can be improved when gap have been observed and evaluated for various conditions. Hand drum form can be improved when gap voltage and spark cycle become smaller, thickness become thinner, wire tension become larger and the no of cutting increases. When 60mm thickness tungsten carbide is cut in normal condition, hand drum form becomes larger due to the low conductivity machining allowance become slightly larger when peak discharge current and gap voltage become larger, or wire tension becomes smaller. Under the same condition, machining allowance of tungsten carbide is larger than alloyed steel by 1/100mm.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.27-36
• /
• 2005

Some studies have shown that unstable factors are inherent in WEDM process, causing the instability of the discharging pulse to reach about 40∼60％ in normal machining. Transient stability is an important subject in WEDM process since there is a close relationship between stability and machining performance, such as the characteristics of a machined surface, machining speed and problem of instability like wire rupture phenomenon. Among the many machining parameters affecting WEDM machining state, three specific parameters (Vr, Ip, off time ) are major controllable variables that can be applied in transient stability control. And, this research investigates the implementation and analysis of real-time micro control of the discharging stability of WEDM (Wire Electric Discharge Machining) process.

• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.253-258
• /
• 2000

Frictional behavior of wire electric discharge machined surfaces of spheroidized annealed STDll steel was investigated. The surfaces were produced with a various series of finish cuts where pulse energy was reduced with increase in the number of finish cuts. Roughness and micro-hardness of the surfaces were also measured. It is observed that the increase in the number of finish cuts produces the surface exhibiting lower frictional resistance followed by higher resistance after considerable wear. Effects of finish cuts on the friction characteristics are discussed with the aid of roughness and micro-hardness of the surfaces.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.58-62
• /
• 2012

Unlike conventional single special cut methods, W-EDM is a combination of multiple-effects. This study focuses on the effects of second cut on the roughness of surfaces treated with W-EDM. W-EDM is, to a large extent, typical unmanned-machining equipment, which represents NC machining equipment that allows long-time full automation. W-EMD is getting popular as a precise machining technology and STD11 is frequently used in press die manufacture. In this study, the former is applied to the latter to look at the effects of second cut on the roughness of surfaces treated with W-EDM.

• 한국CDE학회논문집
• /
• 제6권3호
• /
• pp.206-214
• /
• 2001

This paper describes the wire EDM (Electric Discharge Machining) CAM system considering a variable taper wire-cut and an unmanned wire EDM during the night. Wire EDM is applicable to all materials that are fairly good electrical conductors, including metals, alloys and most carbide. Thus it provides a relatively simple method for making holes of any desired cross section in materials that are too hard or brittle to be machined by most other methods. In this paper we classify variable taper wire-cut machining patterns and variable taper wire-cut geometries. Also we determine unmanned wire EDM patterns fur the productivity of wire EDM industry. Developed system consists of two modules: 1) Variable taper wire EDM module guarantees the length ratio machining function, the parametric ratio machining function and the marking function. 2) Unmanned wire EDM module guarantees the automatic wire EDM during the night. The proposed system has been tested in the fields and found to be a useful system.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.714-719
• /
• 2011

The surface roughness depending on the machining method is very important because is produce a finished product through riveting, sealing, bonding, and special paint in order to curb the turbulence and air resistance which occur between the sheets. Aluminum alloy 2024 which is widely used for interior and exterior material of aircraft are tested. Jin-young JW-60C wire cutting machine was used in this experiment. In this paper, the experimental investigation has been performed to find out the influence of the surface roughness and surface shape characteristics on the wire-cut EDM of discharge energy in aluminium alloy 2024. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. The experimental results give the guideline for selecting reasonable machining parameters. The high discharge energy on the idle time, almost no change in surface roughness can be seen.

• 산업공학
• /
• 제10권3호
• /
• pp.125-132
• /
• 1997

We proposed a 2-step neural network approach for estimating machining parameters of electric discharge wire cut. The first step net, which is described as a backward neuro-estimation, is designed for estimating coarse cutting parameters while the second phase net, as a polishing forward neuro-estimation, is utilized for determining fine parameters. Sequential estimation procedure, based on backward and forward net, is performed using the net's approximation capability which is M to 1 and 1 to M mapping property. Experimental results an given to evaluate the accuracy of the proposed 2-step neuro-estimation.