• Korean Journal of Agricultural and Forest Meteorology
• /
• v.2 no.4
• /
• pp.204-208
• /
• 2000

Little information is available for the temporal variation in air temperature profile within rice canopies under development, while much works have been done for a fully developed canopy. Fine wire thermocouples of 0.003 mm diameter (chromel-constantan) were installed at 10 vertical heights by a 10 cm step in a paddy rice field to monitor the air temperatures over and within the developing rice canopy from one month after transplanting (June 29) to just before heading (August 24). According to a preliminary analysis of the data, we found neither the daytime temperature maximum nor the night time minimum at the active radiation surface (the canopy height with maximum leafages) during this period, which is a typical profile of a fully developed canopy. Air temperature within the canopy never exceeded that above the canopy at 1.5 m height during the daytime. Temporal march of the within-canopy profile seemed to be controlled mainly by the ambient temperature above the canopy and the water temperature beneath the canopy, and to some extent by the solar altitude, resulting in alternating isothermal and inversion structures.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.3
• /
• pp.679-685
• /
• 2004

Although the electrophoretic deposition method has the advantage of simple processing procedure, less fabrication facilities, and easier control for deposition thickness and wire length, providing economical and technical merits, it also has the disadvantages of cracking and porosity phenomena, requiring an improved processing method for higher particle density and constant particle orientation. we have developed an optimization method to increase the particle density and to unify its orientation, and have performed a study to overcome the cracking and porosity problems in the fabricated superconductor. In order to improve the surface uniformity and the conduction properties of the fabricated YBCO thick films, a system that applies alternate voltage vertically has been developed for the first time and applied to the electrophoretic deposition process. The applied alternate electric field caused a force to be exerted on each YBCO particle and resulted in a rotation of the particle in the direction of applied electric field, accomplishing a uniform particle orientation. We name this process as the shaky-aligned electrophoretic deposition method. For commercial utilization and efficiency, in this dissertation, alternating voltage of 60 Hz and 25 ∼ 120 V/cm was proposed to apply it as a subsidiary source for shaky-flow deposition so that the fabricated thin film showed uniform surface morphology with less voids and cracks and Tc,zero of 90 K and the critical current density of 3419 A/$cm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.11
• /
• pp.2689-2696
• /
• 2015

Radioactive isotopes which are manufactured using a cyclotron in a radioisotope used for radiation diagnosis is affected by the production yield according to size and shape of the beam and beam uniform degree from irradiated location when the proton beam investigated the target by cyclotron. Therefore, in this paper developed the BPM(Beam Profile Monitor) device capable of measuring the beam cross-section at the cyclotron beam line. It was configured so as to be able to remote control the BPM device in LabView and used the BPM program it was to be able to easily monitor and display to analyze the graph of two-dimensional graph and a three-dimensional beam distribution numerical information of the beam obtained while scanning the tungsten wire to the X and Y axis. The time it takes to measure the beam can be confirmed 37seconds when step motor driving speed was 2000pps. Through a beam readjusted based on the measured beam distribution information by optimizing the beam distribution it can be made to maximize the RI production yield and contribute supply stabilization.

• Journal of Practical Engineering Education
• /
• v.8 no.2
• /
• pp.111-120
• /
• 2016

Education equipment for field programmable gate array (FPGA) design of sensor-based IOT (Internet Of Thing) system is introduced. Because sensors have different interfaces, several types of interface controller on FPGA need. Using this equipment, several types of interface controller, which can control ADC (analog-to-digital converter) for analog sensor outputs and $I^2C$ (Inter-Integrated Circuit), SPI (Serial Peripheral Interface Bus), and GPIO (General-Purpose Input/Output) for digital sensor outputs, can be designed on FPGA. Image processing hardware using image sensors and display controller for real and image-processed images or videos can be design on FPGA chip. This equipment can design a SOC (System On Chip) consisting of a hard process core on Linux OS and a FPGA block for IOT system which can communicate with wire and wireless networks. Using the education equipment, an example of hardware design using image sensor and accelerometer is described, and an example of syllabus for "Digital system design using FPGA" course is introduced. Using the education equipment, students can develop the ability to design some hardware, and to train the ability for the creative capstone design through conceptual, partial-level, and detail designs.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.10-21
• /
• 1992

The purpose of this study was to investigate the analgesic effect of eugenol, capsaicin and demethoxy-NE. Young adult cats, weighing 2.0 to 3.0kg, were used. Each animal was anesthetized (${\alpha}$-chloralose 60mg per kg body weight) and divided into four groups; control, eugenol, capsaicin and demethoxy-NE group. The anterior digastric muscles were exposed and a pair of electrodes was inserted to record the electromyograms. To expose the pulp, each canine teeth was prepared with a low speed bur under cooling and used for recording anterior digastric muscular EMGs evoked by noxious stimulation of dental pulp. To observe effects on jaw opening reflex, inferior alveolar nerve of both sides were exposed for drug application and wire electrodes were inserted in anterior digstric muscle for recording the EMGs. To observe effects on action potential, saphenous nerves of both sides were exposed and three tissue pools were made from surrounding tissue. The most distal pool was used for applying stimulation, the most proximal one for recording of action potential, and the other one for drug application. One side of inferior alveolar nerve and saphenous nerve were used for eugenol, capsaicin, or demethoxy-NE application, the other side of nerve for control experiments(only vehicle application). Anterior digastric muscular EMGs evoked by noxious stimulation of dental pulp were recorded before drug application, immediate after drug application, at 60 and 120 minutes, and 5 days after drug application. Action potentials were recorded before drug application, immediate after 30 minutes drug application, at 30, 60 and 120 minutes after drug had been washed out. The results were as follows; 1. Eugenol had a continuous blocking effect on the anterior digastric muscular EMGs evoked by noxious pulp stimulation and after 5 days, showed completely blocking effect. 2. After 5 days, demethoxy-NE applied to dental pulp had a considerable blocking effect on the jaw opening retlex evoked by noxious stimulation but capsaicin had no significant effect. 3. After 5 days, eugenol group showed the strongest blocking effect among the all experimental groups on the jaw opening reflex evoked by noxious stimulation of dental pulp and capsaicin group showed the weakest blocking effect. 4. Eugenol had a completely blocking effect on the action potential conductivity of peripheral nerve. Capsaicin and demethoxy-NE had the blocking effect on the action potential conductivity of ${\alpha}$-and C-nerve fibers. 5. Capsaicin, demethoxy-NE and eugenol applied to inferior alveolar nerve surppressed the jaw opening reflex evoked by noxious stimulation of dental pulp.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.22-35
• /
• 1992

The aim of this study was to investigate the effect of herbal organic extracts on the pain response provoked by noxious stimuli on dental nerve and the peripheral nerve conduction. Cats (2-2.5Kg regardless of sex) that were chosen as experimental animals were classified into control group, Asiasari radix application group and Zingiberis rhizoma application group. They were anesthetized with ${\alpha}$-chloralose, then anterior belly of digastric muscle of both sides were exposed and wire electrodes were inserted for recording of Electromyogram (EMG). Cavities were prepared on canines until pulp of the teeth were exposed. And after the drugs solubilized for 2% and 4% concentration (W/V) in vehicle were applied, their effects were compared through the recording of EMG immediately after drug application, 30 minutes, 60 minutes, 120 minutes and 5 days after, respectively. And after both inferior alveolar nerves were exposed, 4% organic extracts of Zingiberis rhizoma and Asiasari radix were applied for 30 minutes then the change of jaw opening reflex provoked by noxious stimuli on pulpal nerves were observed immediately after washing out, at 30, 60 and 90 minutes after drug had been washed out. After saphenous nerve of both sides were exposed, one side of nerve was used for vehicle application and the other side was used for drug application for 30 minutes. Then conduction of action potential of A-${\delta}$ and C-fiders of saphenous nerves, which have changed with time, was recorded. With analysis of these records, the following results were obtained: 1. Organic extract of Zingiberis rhizoma (2% or 4% concentration) greatly suppressed EMG of digastric muscle provoked by noxious stimuli on pulpal nerve at five days after application, the suppressive: effect was greater than that of organic extract of Asiasari radix. 2. Organic extract of Asiasari radix (2% or 4% concentration) suppressed jaw opening reflex provoked by noxious stimuli on pulpal nerve, at 5 days after drug application. 3. Organic extract of Zingiberis rhizoma and Asiasari radix (immediately after 30 minutes application) suppressed neural conduction of A-${\delta}$ and C-fibers, the suppressive effect was greater on A-${\delta}$ fibers than on C-fibers. 4. Jaw opening reflex provoked by noxious stimuli on pulpal nerve in inferior alveolar nerve was greatly suppressed 30 minutes after drug application, this effect was greater by Zingiberis rhizoma than by Asiasari radix.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.11a
• /
• pp.19-20
• /
• 1998

오버레이용접에 의한 표면개질기술(Weld Surfacing or Hardfacing Technology)은 내식성, 내 마모성, 또는 내열성을 갖는 합금의 용접재료를 모재 표면에 균일하게 용착(오버레이:Ovedayer)시킴으로써 목적하는 재료의 표면성질을 향상시키는 표면처리의 한 방법이으로써 1922년 Stoody가 Steel Tube에 Cr합금 분말을 충진한 용접봉을 제조하여 석유시추용 회전드릴의 선단 표면을 오버 레이 용접시켜 내마모성을 획기적으로 개선시킴으로써 이루어 졌다. 초기 오버레이 용접기술은 발전설비I 제철설비I 시벤트설비, 그리고 제지설비 등 주로 설비 부품들의 표면부 내마모성을 개선시키는 방향으로 주로 연구 개발이 이루어졌으나, 기술개발의 진전으로 탈황설비 둥의 표면부 내식성 향상, 연속주조롤 표면부의 내산화성, 내열피로성, 내마모 성 향상 둥을 위해 점차 산업전반에 널리 이용되고 있으며, 설비의 고도화 및 장수명화가 요구되 면서 본 기술의 중요성 또한 점차 부각되고 있다. 그림 1은 연강의 모재 위에 셀프쉴드플럭스코어드와이어(Self-Shield Flux Cored Wire:SS-FCW, 이하 55-FCW라 기술함)를 사용하여 오버레이 용접올 하는 장면을 도식적으로 나 타낸 것이다. 모재와 전극재인 용접봉(S5-FCW) 사이에서 아크가 발생되고, 아크열에 의해서 용접 봉 및 모재 일부가 용융되면서 모재 표면에 새로운 오버레이 표면층이 형성된다. 통상 오버레이 층의 1층 두께는 2-6mm 내외이며, 단층 혹은 다충 오버레이를 자유롭게 실시한다. 오버레이층의 물성은 아크열에 의한 모재로의 용입정도에 따라 1층부에서는 모재의 영향을 크게 받지만 오버레 이충 수가 증가된 3층부에서 부터는 전적으로 용접봉의 성분에 좌우된다. 사진 1은 연강(55-41)의 모재위에 크롬탄화물이 다량 함유된 고크롬 탄화물형 내마모재가 오버 레이된 내마모 복합강판 (wear plate)의 단면 미세조직 사진으로써 모재부와 오버레이충을 함께 보여주고 있다. 모재와 오버레이 충간의 경계면은 모재 일부가 용융된 후 웅고하면서 형성됨으로 인해서 도금이나 용사층과는 달리 매우 견고하게 결합되어 있다. 따라서 계면부의 탈락이라는 문 제점은 거의 없어 심한 응력을 받는 기계구조물 및 부품에도 본 기술은 널리 적용되고 있다. 그리고 사진 1에서 알 수 있는 바와 같이 모재와는 전혀 상이한 재료를 자유로이 선택하여 표면 유효층 일부만 오버레이시키며I 주조 및 단조가 불가능한 재료까지도 표면부에 오버레이 시킴으로 서 부품 및 설비의 제조에 있어 재료비의 절감과 제품의 수명이 획기적으로 개선될 수 있다. 그리고 최근에는 도금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.502-502
• /
• 2007

A catenary system should be designed to have an uniform elasticity over a span in order to maintain the lowest possible loss of contact between a pantograph and a contact wire. A elasticity uniformity of a catenary can be regarded as a important design factor used for predicting the current collection performance for a catenary. There are a couple of formulas to calculate the degree of elasticity uniformity of a catenary according to the literature survey. The effectiveness of these formulas is reviewed by performing catenary elasticity and loss of contact analysis for various different configurations of catenary systems using a beam element based FEM program. The results reveals that these formulas are not suitable to predict the current collection performance for a catenary. Therefore, a new formula based on the standard deviation of the elasticity over a span is proposed in this study. The analysis results show that the new formula for an elasticity uniformity of a catenary is very effective in predicting the current collection performance for a catenary.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.73-82
• /
• 2016

PURPOSES: The national highways and expressways in Korea constitute a total length of 17,951 km. Of this total length of pavement, the asphalt pavement has significantly deteriorated, having been in service for over 10 years. Currently, hot in-place recycling (HIR) is used as the rehabilitation method for the distressed asphalt pavement. The deteriorated pavement becomes over-heated, however, owing to uncontrolled heating capacity during the pre-heating process of HIR in the field. METHODS: In order to determine the appropriate heating method and capacity of the pre-heater at the HIR process, the heating temperature of asphalt pavement is numerically simulated with the finite element software ABAQUS. Furthermore, the heating transfer effects are simulated in order to determine the inner temperature as a function of the heating system (IR and wire). This temperature is ascertained at $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$, $600^{\circ}C$, $700^{\circ}C$, and $800^{\circ}C$ from a slab asphalt specimen prepared in the laboratory. The inner temperature of this specimen is measured at the surface and five different depths (1 cm, 2 cm, 3 cm, 4 cm, and 5 cm) by using a data logger. RESULTS: The numerical simulation results of the asphalt pavement heating temperature indicate that this temperature is extremely sensitive to increases in the heating temperature. Moreover, after 10 min of heating, the pavement temperature is 36%~38% and 8%~10% of the target temperature at depths of 25 mm and 50 mm, respectively, from the surface. Therefore, in order to achieve the target temperature at a depth of 50 mm in the slab asphalt specimen, greater heating is required of the IR system compared to that of the gas. CONCLUSIONS : Numerical simulation, via the finite element method, can be readily used to analyze the appropriate heating method and theoretical basis of the HIR method. The IR system would provide the best heating method and capacity of HIR heating processes in the field.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.70-84
• /
• 2008

A series of the studies on the applied physical properties of domestic species have been conducted last three years. Pinus densiflora was one of the three species examined for the first year. Because the same apparatus and experimental procedures were used for all species, their results can be easily comparable. The experiments for sorption property were conducted with 20- and 80-mesh wood powder and resulted in their EMC's and sorption isotherms at various heating conditions. The thermal conductivity and diffusivity, and electric resistance and volumetric electric resistivity were measured with a thermal-wire device and a high electric resistance meter. The differences of the thermal and electric properties between quarter- and flat-sawn specimens were observed, which was partially attributed to their anatomical differences. An acoustic measurement system was used to evaluate dynamic MOE and internal friction. This paper provides the useful fundamental data for designing a wood structure, correcting a portable resistance-type moisture meter, and nondestructive testing wood.