• The KSFM Journal of Fluid Machinery
• /
• v.7 no.5 s.26
• /
• pp.13-19
• /
• 2004

Centrifugal blowers are widely used for air handling units in industry applications. The blower has a centrifugal impeller and a scroll casing including a driving component such as an electric motor. The impeller takes forward or backward blades to induce flows into the blower, Comprehensive investigation according to the two kinds of blades is systematically carried out for a guidance of design for this kind research. It is observed that flow rate of the blower with forward blades is larger than that of the system with backward blades. Otherwise, the system noise is more pronounced in the case of the blower with forward blades. The reason is due to larger velocity from the rotating forward blades that pose obtuse angle with the circumferential direction. The distinguished characteristics are validated by a parallel experiments with a wind tunnel and in an anechoic chamber. Numerical analysis for the system shows detail information inside the blades and the casing. A series of figures to show the flow details offer deep understanding of the performance of a centrifugal blower with different blades.

• Journal of the Korean Society of Safety
• /
• v.22 no.1 s.79
• /
• pp.24-29
• /
• 2007

The effectiveness of a UV(ultra violet) disinfection system depends on the characteristics of the waste water, flow conditions, the intensity of UV radiation, the amount of time the microorganisms are exposed to the radiation, and the reactor configuration. The wast water flow conditions are important factors in the design of UV disinfection system from the point of enhancement view of UV disinfection. The turbulent energy intensity in the wake by the vortex shedding are effective for UV radiation. Therewith the effectiveness of vortex generator is considered as a enhancement of UV disinfection. The experimental results presented give important evidences and explain that it is possible to predict UV disinfection performance based on flow experiments. An experimental investigation of two types of the vortex generator is presented. The qualitative and quantitative evaluations of the wake are made by flow visualization using smoke wire method and the measurement of vortex frequencies in the wind tunnel. From the experiment, following results were obtained that the delta wing type vortex generator is more effective than circular type because of the higher vortex frequencies and the smaller drag.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.358-363
• /
• 2008

The spray cross-section characteristics of two-phase spray that using external-mixing nozzle injected into a subsonic cross flow were experimentally studied with various ALR ratio that is $0{\sim}59.4%$. Suction type wind tunnel was used and experiments were conducted to ambient environment. Several plain orifice nozzles with L/d of 30 and orifice diameter of 0.5 mm and orifice length 1.5 mm were tested. Free stream velocity profiles at the injection location were measured using hot wire. Spray images were captured to study collision point and column trajectory. Phase Doppler particle analyzer(PDPA) was utilized to quantitatively measuring droplet SMD, volume flux. Measuring probe of PDPA positions was moved 3-way transverse machine. SMD distributions were layered structure and peaked at the top of the spray plume and low value at bottom of the spray. Volume flux of spray was distributed to the two side region and volume flux quantity decreased when ALR ratio increased. It was found that the perpendicularly injected two-phase spray jet of external mixing into a cross flow showing that mistlike spray moved away from the test section bottom region.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.363-366
• /
• 2011

Mixing and combustion experiments with a vent slot mixer were performed in Mach 2 supersonic wind tunnel. Helium and hydrogen gases each were used for the mixing and the combustion experiment with a plasma jet (PJ) torch. The vent slot mixer holds plenty of fuel in the downstream mixing region, even though the fuel is transversely injected. In case of the combustion, the injected fuel is ignited by the PJ torch, and then unburned mixture is burned by shock-induced combustion downstream. Thermal choking in the combustor leads to shock trains in the isolator, causing the unstable combustion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.331-334
• /
• 2011

The performance of ramjet engine is closely associated with a supersonic intake. In this study, experiments and computational simulations were conducted to observe the internal flow characteristics of the supersonic intake. The supersonic intake which have self-starting characteristics was designed and manufactured. The flow characteristics was analyzed from the experimental results using the supersonic wind tunnel testing and computational results using RANS equation and Menter's SST turbulence model. The detailed visualization results were suggested for the pseudo-shock wave of stable operations and for the inlet buzz phenomenon of unstable operations.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.9-14
• /
• 2006

This study presented the feasibility of R152a refrigerant as an alternative of R134a which is used in the current automobile air conditioning system. The performance of air conditioning system installed in the actual vehicle was tested using the climate wind tunnel. The experiments were conducted at various refrigerant charge quantities and various driving conditions such as city traffic, highway traffic and parking. Same components and lubricant were used for both R134a and R152a system. The effects of air set values of thermal expansion valve on the performance were also investigated. In case of the R152a system, refrigerant charge quantity can be reduced about 20%, better performance and superior compressor durability is expected due to the lower discharge pressure compared to the R134a system.

• Journal of the Korea Society for Simulation
• /
• v.28 no.3
• /
• pp.83-89
• /
• 2019

This research describes quantitative effects of initial dispersion conditions upon the dispersion randomness of Magnus rotor bomblets. Ratios of the missile spin rate to the missile velocity, a, flight path angles, ${\gamma}$ and altitudes, h, were changed to investigate their effects on dispersion randomness. Dispersion was analyzed through calculation of 6 degree of freedom motion equation with aerodynamic coefficients from wind tunnel experiments. In order to analyze the randomness, regression analysis is adopted to calculate the coefficient of determination. The optimized ratio of the missile spin rate to the missile velocity and flight path angle were obtained and the dispersion altitudes had more effect on the dispersion diameter and had less effect on dispersion than other parameters.

• Journal of the Korean Society for Railway
• /
• v.19 no.1
• /
• pp.11-19
• /
• 2016

The flows around a high speed train are very important because they could affect the aerodynamic characteristics such as drag and acoustic noise. Especially the boundary layer of flows could represent the characteristic of flows around the high speed train. Most previous studies have focused on the boundary layer region along the train length direction for the side of the train and underbody. The measurement and analysis of the boundary layer for the roof side is also very important because it could determine the flow inlet condition for the pantograph. In this study, the roof boundary layer was measured with a 1/20 scaled model of the next generation high speed train, and the results were compared with full-scaled computational fluid dynamics results to confirm their validity. As a result, it was confirmed that the flow inlet condition for the pantograph is about 85% of the train speed. Additionally, the characteristics of the boundary layer, which increases along the train direction, was also analyzed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.1
• /
• pp.45-53
• /
• 2009

A possibility of the drag coefficient estimation in numerical water basins was discussed where the numerical solution were calculated by the 3-dimensional hydro-dynamical model (FLOW-$3D^{(R)}$) with the RNG $k-{\varepsilon}$ turbulence model. On the known cases of the drag coefficients for a rectangle, the numerical drag coefficients got $1.34{\sim}1.52$ and the wind tunnel values were $1.3{\sim}1.5$. For a cylinder, the numerical values were calculated as $0.75{\sim}0.78$ in the range of 0.5

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.99-108
• /
• 2020

In the field of aircraft icing prediction, surface roughness has been considered as critical factor because it enhances convective heat transfer and changes local collection efficiency. For this significance, experimental studies have been conducted to acquire the quantitative data of the formation process. Meanwhile, these experiments was conducted under low-speed condition due to the measurement difficulties. However, it has not been investigated that how the flow characteristic of low-speed will effects to the surface roughness. Therefore, the present study conducted experiment under low-speed icing condition, and analyzed the relation between surface roughness characteristics and icing condition. As an analysis method, the dominant parameters used in the previous high-speed experiments are employed, and roughness characteristics are compared. The size of roughness element was consistent with the previous known tendency, but not the smooth zone width.