• Geotechnical Engineering
• /
• v.14 no.4
• /
• pp.33-46
• /
• 1998

Anisotropy of stiffness, from extremely small strains to post-failure strains, of isotropically consolidated air-pluviated sands in plane strain compression was studied by using the newly developed instrumentation for small strain measurements. Seven types of sand of the world-wide origins were tested, which have been extensively used for research purposes. Stress-strain at the specimen boundaries. It was found that the maximum Young's modulus $E_{max}$ was irrespective of the angle $\delta$ of the $\delta_1$ direction relative to the bedding plane. However, the normalized$ E_{max}$ was varied with the types of sand. Furthermore, the dependency of the strain and stress level on the stiffness was increased as $\delta$ decreased.

• Spatial Information Research
• /
• v.9 no.1
• /
• pp.1-13
• /
• 2001

Nowadays, SAR Interferometry is actively being studied as a new technique in topographic mapping using satellite imagery. It extracts height values using phase information derived by two SAR imageries covering same areas. Unlike when using SPOT imagery, it is not affected by atmospheric conditions and time. So to speak, we can say that SAR Interferometry is flexible in imagery acquisitions and can get height data economically over wide area. So, it is expected that SAR Interferometry will be widely using in GIS applications. But, in some area occurring geometric distortion, height data are misjudged or not extracted depending on phase unwrapping algorithms. IN the case of ERS tandem data, the accuracy of height data was worst in mountain area. It is the because of the short incidence angle resulted in layover effect. Of the phase unwrapping algorithms, path-following was better in height accuracy but could not get data in layover area. In this area, we could get height data using Height Sensitivity. In concludion, we could get DEM that maintained the accuracy of path-following method and have overall data across imagery.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.1
• /
• pp.65-72
• /
• 1992

The purpose of this study was to evaluate the flexure stregth of posterior 4-unit acrylic resin bridge with different pontic designs : 1) Conventional pontic 2) Hygienic pontic and 3) Modified hygienic pontic. All specimens were made of self-curing acrylic resin for provisional restorations. Self-curing acrylic resin was filled in a silicone mold by the drop-on technique ; and was polymerized in a pressure spot under 20 psi pressure. The test specimens which were simply shaped posterior 4-unit bridge were 38mm ion 4mm wide, and 35mm thick(connector : 3mm thick). Each specimen was subjected to an increasing load of Instron machine with its tip centered on the specimen at 90-degree angle, and the machine was operated with its load cell of 50kg and its crosshead speed, 2mm/minute : and then the load values at the moment of the fracture of them were recorded. This study was also performed to analyze their stress distributions by the finite element method. The obtained results were as follows : 1. Flexure strength of the hygienic pontic(9.78kg) and the modified hygienic pontic(10.17kg) was higher than that of conventional pontic(6.96kg). But no significant difference was found between the hygienci pontic and the. modified hygienic pontic. The above statistic values were appraised by ANOVA and Duncan's multiple range test 2. Stress was concentrated on the middle portion in every group : and the stress of conventional pontic was found the greatest of all pontic designs.

• The Journal of the Korea Contents Association
• /
• v.14 no.10
• /
• pp.1-9
• /
• 2014

Generally, integral image used for autostereoscopic 3d display is generated for flat lens array, but flat lens array cannot provide a wide range of view for generated integral image because of narrow range of view. To make up for this flat lens array's weak point, curved lens array has been proposed, and due to technical and cost problem, approximate surface lens array composed of several flat lens array is used instead of ideal curved lens array. In this paper, we constructed an approximate surface lens array arranged for $20{\times}8$ square flat lens in 100mm radius sphere, and we could get about twice angle of view compared to flat lens array. Specially, unlike existing researches which manually generate integral image, we propose an OpenCL GPU parallel process algorithm for generating real-time integral image. As a result, we could get 12-20 frame/sec speed about various 3D volume data from $15{\times}15$ approximate surface lens array.

• Archives of Plastic Surgery
• /
• v.32 no.3
• /
• pp.287-292
• /
• 2005

The definitive correction of secondary lip nasal deformities is a great challenge for plastic surgeons. To rectify the secondary lip nasal deformities, various procedures and its modifications have been reported in many centers. However, no universal agreement exist to correct the various components of secondary nasal deformities. The secondary nasal deformity of the unilateral cleft lip has its own characteristic abnormalities including the retroplaced dome of the ipsilateral nasal tip, hooding of the alar rim, a secondary alar-columellar web, short columella, depressed alar base and so forth. Among these components of secondary nasal deformity, maxillary hypoplasia, especially in the area of piriform aperture, and alveolar bone defect can make the alar base depressed, which in turn, leads to wide and flat nasal profile, obtuse nasolabial angle coupled with subnormal nasal tip projection in aspect of aesthetic consideration. Moreover, the maxillary hypoplasia contributes to reduced size of the nasal airway in combination with other component of external nasal deformity and therefore the nasal obstruction may be developed functionally. Therefore, the current authors have performed corrective rhinoplasty with the augmentation of alar base with various methods which include rearrangement of soft tissue, vertical scar tissue flap and use of allogenic or autologous materials in 42 patients between 1998 and 2003. The symmetric alar base could be achieved, which provides the more accurate evaluation and more appropriate management of the various component of any coexisting secondary nasal deformity. In conclusion, the augmentation of alar base, as a single procedure, is a basic and essential to correct the secondary lip nasal deformities.

• Asian Journal of Turfgrass Science
• /
• v.20 no.1
• /
• pp.1-10
• /
• 2006

This study was carried out to develope new zoysiagrass cultivar 'Millock'(Patent registration No. : 10-2005-0110051). Artificial selfing of collected line of MJ8 was conducted to develope F1 plant (MJ8S). Among the inbred progenies, MJ8S-9 (Millock) showed superior performance in color, density, and rust resistance. 'Millock' showed genetically dark green color, with medium-textured leaf ($4.2{\pm}0.44$ mm), short internode length ($3.5{\pm}0.28$ cm), and wide leaf angle ($52.5{\pm}10.8$ degree). Height to the lowest leaf blade of this cultivar was $1.9{\pm}0.91$ cm, which may allow low mowing height. 'Millock' has a yellowish green stolen. Also, specific bands with primer number OPB 8 by RAPD analysis can be used for a cultivar identification.

• Geomechanics and Engineering
• /
• v.19 no.5
• /
• pp.393-405
• /
• 2019

This paper evaluates the geotechnical and geo-engineering properties of the South Pars Zone (SPZ) marls in Assalouyeh, Iran. These marly beds mostly belong to the Aghajari and Mishan formations which entail the gray, cream, black, green, dark red and pink types. Marls can be observed as rock (soft rock) or soil. Marlstone outcrops show a relatively rapid change to soils in the presence of weathering. To geotechnically characterise the marls, field and laboratory experiments such as particle-size distribution, hydrometer, Atterberg limits, uniaxial compression, laboratory direct-shear, durability and carbonate content tests have been performed on soil and rock samples to investigate the physico-mechanical properties and behaviour of the SPZ marls in order to establish empirical relations between the geo-engineering features of the marls. Based on the experiments conducted on marly soils, the USCS classes of the marls is CL to CH which has a LL ranging from 32 to 57% and PL ranging from 18 to 27%. Mineralogical analyses of the samples revealed that the major clay minerals of the marls belong to the smectite or illite groups with low to moderate swelling activities. The geomechanical investigations revealed that the SPZ marls are classified as argillaceous lime, calcareous marl and marlstone (based on the carbonate content) which show variations in the geomechanical properties (i.e., with a cohesion ranging from 97 to 320 kPa and a friction angle ranging from 16 to 35 degrees). The results of the durability tests revealed that the degradation potential showed a wide variation from none to fully disintegrated. According to the results of the experiments, the studied marls have been classified as calcareous marl, marlstone and argillaceous lime due to the variations in the carbonate and clay contents. The results have shown that an increase in the carbonate content leads to a decrease in the degradation potential and an increase in the density and strength parameters such as durability and compressive strength. A comparison of the empirical relationships obtained from the regression analyses with similar studies revealed that the results obtained herein are reasonably reliable.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.94-102
• /
• 2013

We propose the mirror active element pattern (AEP) method for the radiation pattern computation of linear array antennas versus scan angles. The computation time for the radiation pattern of linear array antennas using the mirror AEP method is reduced by almost half compared to that using the AEP method because the number of AEPs of elements obtained by the full-wave simulation necessary for the radiation pattern computation of linear array antennas is reduced by almost half. The difference between the radiation patterns of linear array antennas obtained by the full-wave simulation and mirror AEP method is very small for wide scan angle range when the radiation pattern of an antenna element is symmetric.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.590-596
• /
• 2019

To improve the color gamut of a liquid-crystal display (LCD), we propose a bandpass filter that is added to the backlight unit to optimize the backlight spectrum. The bandpass filter can only transmit red, green and blue light in the visible range, while reflecting the unwanted light. We study the optical properties of the bandpass filter using the transfer-matrix method, and the effect of the bandpass filter on the color gamuts of LCDs is also investigated. When a bandpass filter based on a 5-layer configuration comprising low and high refractive indices ((HL)²H) is used in phosphor-converted white-light-emitting diode (pc-WLED), K₂SiF₆:Mn⁴⁺ (KSF-LED), and quantum-dot (QD) backlights, the color gamuts of the LCDs improve from 72% to 95.3% of NTSC, from 92% to 106.7% of NTSC, and from 104.3% to 112.2% of NTSC respectively. When the incident angle of light increases to 30°, the color gamuts of LCDs with pc-WLED and KSF-LED backlights decrease by 2.9% and 1% respectively. For the QD backlight, the color gamut almost does not change. When the (HL)²H structure is coated on the diffusion film, the color gamut can be improved to 92.6% of NTSC (pc-WLED), 105.6% of NTSC (KSF-LED), and 111.9% of NTSC (QD). The diffusion film has no obvious effect on the color gamut. The results have an important potential application in wide-color-gamut LCDs.

• Korean Journal of Optics and Photonics
• /
• v.26 no.4
• /
• pp.209-216
• /
• 2015

A new method is proposed for optimal management of the fabrication and assembly tolerance of optical systems. The practical utility of the method is shown by applying it to a wide-angle anamorphic IR optical system. In this method the wavefront error of an optical system is expressed in terms of Zernike polynomials, and the sensitivity of the expansion coefficients to the variation of design parameters is analyzed. Based on this sensitivity analysis, the optimal tolerances of the fabrication parameters are determined and the best compensators for the assembly process are selected. By using this method, one can accurately predict with good confidence the best possible performance of a completed optical system in practice.