• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1142-1148
• /
• 2006

The floating ring seal which is used in the high pressure turbo pump is frequently used in the oxidizer pump and the fuel pump of the turbo pump of the liquid propulsion rocket, because it is able to minimize clearance to decrease the leakage flow rate. But, floating ring seal has a tendency to increase the force which caused instability of system as the eccentricity ratio increases. In this paper, we devised design of floating ring seal which decrease contact area between floating and supporting ring. Modified floating ring seal has a tendency to decrease the eccentricity ratio compare with original floating ring seal. The whirl frequency ratio which is able to distinguish stability of system decrease compare with original floating ring seal

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.329-336
• /
• 2004

The lock-up position of the floating ring seal affects the leakage flowrate and the stability. And it is changed depending on the operating and geometry condition. In this paper, the leakage flowrate and stability with change of the height and length were investigated by theoretical analysis and experiment. The parameter of the height and length is expressed to the b and L. The decreasing of the b resulted in the increasing of equivalent whirl frequency ratio in the experimental result at the low speed and high pressure not such as theoretical analysis. As the L increased the leakage flowrate decreased and stiffness and direct damping coefficient increased in the experimental result. That was similar to the theoretical analysis.

• 한국유체기계학회 논문집
• /
• 제7권6호
• /
• pp.21-27
• /
• 2004

The floating ring seal has an advantage to find the optimum position by itself, which is used in the turbo pump of a liquid rocket. The main purpose of seals is to reduce the leakage. Especially, seals of the turbo pump for the liquid rocket engine are operated under the serious conditions such as high pressure above 10 MPa, very low temperature about $-180^{\circ}C$ and high rotating speed above 25,000 rpm. So, rotordynamic stability is very important for the system stability. In this paper, the leakage and dynamic characteristics of floating ring seals were investigated by a experimental and analytical method. The theoretical results of the leakage performance for the floating ring seal showed much higher than that of experimental results. On the other hand, the results of stiffness and damping characteristics showed similarity each other. As the shaft speed was increasing, the whirl frequency ratio was increased in the experimental results.

• International Journal of Fluid Machinery and Systems
• /
• 제3권1호
• /
• pp.67-79
• /
• 2010

Severe flexural vibration of the rotor shaft of a Francis turbine runner was experienced in the past. It was shown that the vibration was caused by the fluid forces and moments on the backshroud of the runner associated with the leakage flow through the back chamber. The aim of the present paper is to study the self-excited rotor vibration caused by the fluid force moments on the backshroud of a Francis turbine runner. The rotor vibration includes two fundamental motions, one is a whirling motion which only has a linear displacement and the other is a precession motion which only has an angular displacement. Accordingly, two types of fluid force moment are exerted on the rotor, the moment due to whirl and the moment due to precession. The main focus of the present paper is to clarify the contribution of each moment to the self-excited vibration of an overhung rotor. The runner was modeled by a disk and the whirl and the precession moments on the backshroud of the runner caused by the leakage flow were evaluated from the results of model tests conducted before. A lumped parameter model of a cantilevered rotor was used for the vibration analysis. By examining the frequency, the damping rate, the amplitude ratio of lateral and angular displacements for the cases with longer and shorter overhung rotor, it was found that the precession moment is more important for smaller overhung rotors and the whirl moment is more important for larger overhung rotors, although both types of moment due to the leakage flow can cause self-excited vibration of an overhung rotor.

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.105-111
• /
• 2006

The floating ring seal which is used in the high pressure turbo pump is frequently used in the oxidizer pump and the fuel pump of the turbo pump of the liquid propulsion rocket, because it is able to minimize clearance to decrease the leakage flow rate. Compared with contact seal, the floating ring seal has advantage of minimizing clearance without rubbing phenomenon. But, the floating ring seal has a tendency to increase instability in operating condition in the high speed region. In this research, we devised floating ring seal which is inserted bump in the outer surface in order to improve the stability in the high speed region. Through this work, we expect to improve stability of floating ring seal with increasing the direct damping coefficient of seal and decreasing the eccentricity ratio.

• 한국소음진동공학회논문집
• /
• 제11권8호
• /
• pp.322-330
• /
• 2001

The stability and the leakage performance of turbo pump unit seals supported by elastic-ring ball bearings are Investigated for the Improvement of onset speed of instability(OSI). The numerical analysis of floating ring seal in consistence with its geometry and operating conditions is executed with detailed comparison of various seal types. The results show that the floating ring seal has superior performance in terms of rotordynamic salability compared to the ocher type seals while it shows slightly inferior leakage performance. To Improve the leakage performance. floating ring seal could be combined with hole Pattern damper or labyrinth seal surface.

• 대한기계학회논문집A
• /
• 제29권2호
• /
• pp.239-246
• /
• 2005

A rotor dynamic analysis is implemented to confirm the vibration stability of the high speed centrifugal chiller coupled with gear system. As the rotating speed of the centrifugal chiller under investigation is increased up to 17605rpm at the pinion rotating part, the bearing instability is getting higher and, furthermore, the rotor-bearing system might experience a few critical speed which lead to system failure due to the excessive vibration. In this study, considering the loading capacity and stability conditions, offset journal bearings are adopted for the pinion rotating system and general cylindrical bearings are used for motor part. From the modal analysis, the system is found to be stable as the critical damping ratio which shows the damping characteristics of the system are positive over all operating ranges, and in addition, the synchronous rotating frequency does not come across with any whirl natural frequency. From these results the authors confirm the vibration stability of the rotor-bearing system suggested in this study.

• 한국산학기술학회논문지
• /
• 제4권3호
• /
• pp.193-198
• /
• 2003

증속기어장치를 이용한 고속회전 터보냉동기 시스템에 대한 회전체 동역학 설계 및 해석을 수행하였다. 특히 피동축의 회전수가 17,605 rpm가지 상승하여 회전체 안정성에 문제가 될 것으로 예측하여 특수베어링의 일종인 Offset베어링을 적용하였고, 구동축의 베어링은 단순베어링인 진원형 베어링을 적용하였다. 모드해석결과 회전체 시스템의 고유진동수가 어떠한 가진성분과 교차하지 않는 것이 확인 되었고, 전 운전영역에 걸쳐 감쇠값이 양의 값을 갖는 것을 알 수 있었으며 설계된 회전체 시스템이 정격운전 상태에서 충분한 안정성을 갖고 작동할 수 있음을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제25회 춘계학술대회
• /
• pp.111-121
• /
• 1997

The stability of a rotor-bearing system supported by swirl-controlled hybrid journal bearing with pair-type angled injection orifices is investigated for improvement of the whirl frequency ratio by allowing effective control of the tangential flow inside the bearing clearance, i.e., by achieving more freedom in controlling strength and direction of the supply tangential flow inside the bearing clearance. It is suggested that the system instability can be improved through the change of bearing dynamic characteristic parameters with the swirl control. The orifice diameter d$_0$ and recess injection angle $\alpha$ along with combinations of swirl/anti-swirl supply pressures and directions (3.0-3.0MPa, 4.0-2.0MPa, 2.0-4.0MPa) are selected for design parameters for swirl-controlled effective factors dependent on journal speeds (3000, 9000, 15000, 21000 rpm). It has been found that the orifice diameter do shows strong effects on effective maneuverability of direct-stiffness and direct damping values, while recess injection angle $\alpha$ results in substantial magnitude and direction of cross-stiffness. Specifically, recess injection parameters which are functions of angle of orifice feeding flow and recess dimensions showed very feasible effect on the stability of swirl-controlled rotor-bearing system.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.63-72
• /
• 1997

The stability of a rotor-bearing system supported by swirl-controlled hybrid journal bearing with pair-type angled injection orifices is investigated for improvement of the whirl frequency ratio by allowing effective control of the tangential flow inside the bearing clearance, i.e., by achieving more freedom in controlling strength and direction of the supply tangential flow inside the bearing clearance. It is suggested that the system instability can be improved through the change of bearing dynamic characteristic parameters with the swirl control. The orifice diameter $d_0$ and recess injection angle $\alpha$ along with combinations of swirl/anti-swirl supply pressures and directions (3.0~3.0 MPa, 4.0~2.0 MPa, 2.0~4.0 MPa) are selected for design parameters for swirl-controlled effective factors dependent on journal speeds (3000, 9000, 15000, 21000 rpm). It has been found that the orifice diameter $d_0$ shows strong effects on effective maneuverability of direct-stiffness and direct damping values, while recess injection angle $\alpha$ results in substantial effects on the magnitude and direction of cross-stiffness. Specifically, recess injection parameters which are functions of angle of orifice feeding flow and recess dimensions showed very feasible effect on the stability control of swirl-controlled rotor-bearing system.