• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.836-842
• /
• 2001

The more sophisticated patterns of propagation model is presented in this paper, which includes three different source characteristics. The spherical, cosine and dipole radiation characteristics compared and sound event level and the maximum sound level are calculated by experiment and calculation. It is shown that patterns of propagation has dipole characteristics for low speed range(below about 150km/h) at electric multiple system. We know that push-pull high speed system(maximum speed: 300km/h) has cosine characteristics of noise propagation. For this purpose, We conduct the experiment of noise and know the empirical formula of noise level and radiation coefficient K. This model of simulation is conducted through point source array model at wheel/rail contact point by using program and experimental formula. We can guess prediction of profile, flat and wear of wheel by above modeling in near field.

• 한국철도학회논문집
• /
• 제8권5호
• /
• pp.444-453
• /
• 2005

The safety evaluations of railway wheelsets make use of the static fracture toughness obtained in ingot materials. The static fracture toughness of wheelset materials has been extensively studied by experiments, but the dynamic fracture toughness with respect to wheelset materials has not been studied enough yet. It is necessary to evaluate the characteristics of the fracture mechanics depending on each location for a full-scale wheelset for high-speed trains, because the load state for each location of the wheelset while running is different the contact load between the wheel and rail, cyclic stress in the wheel plate, etc. This paper deals with the fracture toughness depend on load rates. The fracture toughness depending on load rate data shows that once the downward curve from quasi-static values was reached, subsequent values showed a slow increase with respect to the impact velocity. This means that dynamic fracture toughness should be considered in the design code of the wheelset material.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.125-130
• /
• 2001

It is vary importance that stopping distance for the freight train and need to design parameter of the brake force and friction coefficient. Acoording to the brake force between shoe and wheel less than the adhesion between wheel and rail. Because of vary difference between empty and weight car of 0∼500kN, this solution was made to application for variable loaded brake system. When the V=110km/h. the emergency stopping distance of freight train is about 700m, so this study was considered on the two condition, one of the increse brake force and to be different of the increse friction coefficient on the brake shoe. It was useful increse friction coefficient. Result of study, analyze effect of the brake shoe on the brake force of the freight car and high friction coefficient were proposed. To do this, ${\mu}$=0.155${\pm}$10% when S=600m on the V=110km/h of the train, 2 groove of friction surface on the temperature distribution were considered.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.109-114
• /
• 2007

For the safety of railway, it should be evaluated for the running safety by measuring the derailment coefficient. Although railway has run the fixed and maintained rail, some of railway is derailed. This report shows the results that performed the static load test, wheelset manufacturing for test, main line running test on the basis of the derailment theory and experience. It is executed main line test to 120 km/h for estimating the running safety of express train in Incheon International Airport. As the test results, could confirm the curving performance and running safety of Incheon International Airport EMU from the results of the wheel unloading, lateral force, derailment coefficient etc. Derailment coefficient was less than 0.8, and lateral force allowance limit and wheel load reduction ratio were enough safe.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1746-1751
• /
• 2007

The bullet train runs more than 200km/h so that it is invisible to the naked eye. For this reason, KTX solely dependent on the ATC operation system. Above all things, 'stability' and 'regular time' are essential to Train Control Operation system. But intermittently, there is a signal transmission problem between ATC operation facilities and ground equipments. which is caused by wheel sliding and friction coefficient between wheel and rail when the train starts. This paper analyzed train service data for one year for accurate survey. In addition, this thesis examines the main cause of a signal transmission problem through simulation and experiment. Further, the method to solve the conventional problem is presented.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.849-854
• /
• 2008

For the running safety assessment of Saemaul train passing through curves, an analysis model for multibody system has been developed. By using this model and ADAMS/Rail, sensitivity analyses depending on the variation of parameters related to the derailment coefficients have been conducted. According to the increase of running speed, the derailment coefficient and unload ratio were increased. At high speed, the derailment coefficient and unload ratio of left wheel showed higher than right wheel. If the cant increased, the derailment coefficient and unload ratio increased. but decreased based on the balance cant value by the curvature and running speed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.813-819
• /
• 2008

For the wear characteristics assessment of Saemaul train passing through curves, an analysis model for multi-car system has been developed. By using this model and ADAMS/Rail, sensitivity analyses have been conducted for the wear characteristics by changing the related parameters. According to the increase of running speed, the wear number, the sliding mean and friction coefficient were increased. At high speed, the wear number, the sliding mean and friction coefficient of left wheel showed higher than right wheel. If the cant increased, the wear number the sliding mean and friction coefficient increased. but decreased based on the balance cant value by the curvature and running speed.

• 산업기술연구
• /
• 제20권B호
• /
• pp.95-103
• /
• 2000

A model trains must have similitude with its original model not only in shape but also in motion. Motion characteristics of a model train under considerations are maximum velocity in straight and circular tracks and stopping distance. Equations of motions are derived to obtain maximum speed and stopping distance based on the Newton's Second Law and the energy principal. To accurately predict traction and resistance force between wheel and rail. wheel slip, or creepage, is taken into consideration. To verify the equations of motion, various experiments have been carried out including measurement of gear efficiency, location of mass center, rolling resistance force, traction force, slip, maximum velocity and stopping distance. This paper addresses how the experiments are setup and carried out in detail. Also the results of experiments are compared with the analytical prediction, which showed good agreements with each other.

• 유공압시스템학회:학술대회논문집
• /
• 유공압시스템학회 2010년도 춘계학술대회
• /
• pp.93-97
• /
• 2010

Wheel skids may occur during train operations due to low adhesion at the wheel-rail contact point abnormally, and the skids, in turn, result in flats appearing on the wheels, which affect safety and ride comfort significantly. Thus, anti-skid control has a crucial role for safe braking and prevention from flats that could cause a disastrous train accident. This paper presents simulation studies on an anti-skid control unit (ASCU) with a brake system of a rolling stock including a pneumatic model for brake power supply and dump valve operation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.755-761
• /
• 2003

The dynamic analysis of the KTX can predict the dynamic motions which occurred in test drive. In this study an analytical model of the KTX is developed to find the critical speed. The numerical analysis for the nonlinear equation motions of 17 degrees of freedom show the running stability and the critical speed due to the hunting motion of the KTX. Also, the vibration modes of the KTX are calculated using the ADAMS/RAIL software, which show that the critical speed occurs for the yawing modes of the car body and the bogie. Finally, this paper shows that the critical speed of the KTX could be changed with the modifications of the design parameters of wheel conicity and wheel contact point.