• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.1
• /
• pp.59-64
• /
• 1999

This paper investigated optimum drying time of PCB and the relationship between humidity in PCB and solderability. As experimental results, soldering was improved with increasing drying time. The wetting time of a dry specimen was shorter about 0.2 seconds than that of a wet specimen. The wetting force was Increased by 2~4mN after drying the wet specimen. When PCB was dried over 30 minute, solder defects and tensile strength of soldered joints was optimized. Effects of drying tome of PCB on the soldering, wetting curve, soldered shape, solder ball, and tensile strength, were investigated.

• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.115-118
• /
• 2009

The use of dolomite refractories has increased during the past several years in the manufacturing of clean steel during the stainless steelmaking process. However, at the same time, the use of dolomite refractories has led to what is known as the skull formation. In the present work, to understand the skull formation, the wetting characteristics of dolomite substrates by liquid Fe-19wt%Cr-10wt%Ni alloys in various oxygen partial pressures were initially investigated at 1753K using the sessile drop technique. For comparison, the wetting characteristics of alumina substrates were investigated with the same technique. It was found that the wetting index, (1+$cos{\theta}$), of dolomite is approximately 40% higher compared to those of alumina. In addition, the oxygen partial pressure to generate the surface oxide, which may capture the liquid metal on the refractory surface, for dolomite is much lower than that for alumina. From this study, it was concluded that the use of dolomite is much more closely associated with the skull formation compared to the use of alumina due to the stronger wettability and the surface oxide formation at a lower oxygen partial pressure of dolomite.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.497-502
• /
• 2005

This study investigated the effects of the substrate and powder content on the fabrication of SiO$_{2}$ photonic crystals by evaporation method. Photonic crystals were self-assembled on quartz, Corning 1737 glass, slide glass, and ITa glass to verify the effects of the wetting angle and surface morphology. The powder contents of the solution were varied from 0.2 to 2.0 wt$\%$. The number of photonic crystal layers increased according to the decrease of wetting angle and surface roughness. The resultant photonic crystals showed the best optical characteristics when the number of photonic crystal layers was within 40 and 50. In addition, the intensity peak of Fabry¡?Perot fringes increased when the wetting angle was large and the particle size was small. Photonic crystals coated on ITO glass showed the highest reflectance peak of 63$\%$ relative intensity.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.12
• /
• pp.2062-2072
• /
• 2010

This research evaluates the change of the water absorbency and drying speed of a quick-drying knit fabric by repeated laundering and laundering conditions and investigates the influence of laundering conditions on the functional properties of the knit fabric. Four factors of laundering conditions were studied: detergent, water hardness, water temperature, and frequency of rotation. Knit fabrics were washed for 25 laundering cycles in a drum-type washing machine with nine different laundering conditions derived from an orthogonal array. The properties of knit fabrics were measured with a drop absorption test, a strip test, and a drying time test. Relaxation shrinkage pointed to a change in the structural characteristics of the knit fabric. Wetting time was faster and wickability was greater in the knit fabrics that underwent 5 laundering cycles; in addition, there were no obvious changes in wetting time and wickability. The detergent was the most important factor in wetting time (40.4%) and wickability (60% or above). Water hardness, water temperature and RPM had less of an effect on wetting time and wickability. There were no significant differences between the levels of laundering conditions (except for detergent) on wetting time and wickability. Drying times with neutral and alkali were slower by repeated laundering; however, there was no obvious change in drying time. Hardness, water temperature and RPM had less of an impact on drying time.

• Textile Coloration and Finishing
• /
• v.21 no.2
• /
• pp.7-13
• /
• 2009

The effects of 0.1g/dl nonionic surfactant solutions on liquid wetting and retention properties of wool fabric are reported. The 10 different nonionic surfactants (Span 20, Tween 20, 40, 60, 80, 21, 61, 81, 65, 85), wool cloth (EMPA 217), and wool soiled cloth (EMPA 107) are used in the study. Both EMPA 217 and 107 have water contact angle($\Theta$)>$90^{\circ}$, which indicates that water spreading over a fabric surface and penetration into the fabric rarely occur. However, EMPA 217 and 107 are easily wetted with perchloroethylene(PCE) having very low values of $\Theta$'s and high values of liquid retention. Water wetting properties are greatly improved by adding nonionic surfactants into the system. Generally, hydrophilic surfactants which have low number of carbon atoms or unsaturated hydrophobic structures are effective in improving water wetting of wool fabrics. The water retention of EMPA 217 and 107 in surfactant solutions have positive relations with $cos{\Theta}$, adhesion tension, and work of adhesion. 40.3% pore volume of EMPA 217 and 26.1% pore volume of EMPA 217 can be filled with water even when we assume $cos{\Theta}=1$ (${\Theta}=0^{\circ}$).

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.2
• /
• pp.30-34
• /
• 2014

Membrane distillation (MD) is a thermal driven separation process in which separation a hydrophobic membrane is a barrier for the liquid phase, letting the vapor phase pass through the membrane pores. Therefore, a porous and hydrophobic membrane should be used in membrane distillation. MD cannot work if water penetrates into the pores of the membrane (membrane wetting). Accordingly, it is necessary to prevent wetting of MD membranes and to remove water inside the pores of the wetted membranes if possible. In this context, our study aimed to develop methods to recover wetted membranes in MD processes. Poly-vinylidene fluoride (PVDF) membranes were used in this study. A laboratory-scale direct contact MD (DCMD) system was used to examine the effect of operating parameters on wetting. For dewetting the wetted membranes, specific techniques including the use of high temperature air were applied. The performances of the membranes before and after dewetting were compared in terms of flux, salt rejection and liquid entry pressure(LEP). The surface morphology of dewetted membrane was confirmed by scanning electron microscope (SEM).

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.3
• /
• pp.343-350
• /
• 2016

Membrane distillation (MD) is a novel separation process that have drawn attention as an affordable alternative to conventional desalination processes. However, membrane fouling and pore wetting are issues to be addressed prior to widespread application of MD. In this study, the influence of ultrasonic irradiation on fouling and wetting of MD membranes was investigated for better understanding of the MD process. Experiments were carried out using a direct contact membrane distillation apparatus Colloidal silica was used as a model foulants in a synthetic seawater (35,000 mg/L NaCl solution). A vibrator was directed attached to membrane module to generate ultrasonic waves from 25 kHz (the highest energy) to 75 kHz (the lowest energy). Flux and TDS for the distillate water were continuously monitored. Results suggested that ultrasonic irradiation is effective to retard flux decline due to fouling only in the early stage of the MD operation. Moreover, wetting occurred by a long-term application of ultrasonic rradiation at 75 kHz. These results suggest that the conditions for ultrasonic irradiation should be carefully optimized to maximize fouling control and minimize pore wetting.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.140-145
• /
• 2011

The effects of nonionic surfactant solutions of 0.1g/dL on detergency and liquid wetting/retention properties of soiled polyester/cotton(65/35) cloth were studied. Soiled polyester/cotton(65/35) cloth (EMPA 104) and 10 different nonionic surfactants (Span 20, Tween 20, 40, 60, 80, 21, 61, 81, 65, 85) were used in the study. The water retention and liquid retention capacity values of soiled cloth were decreased compared with those of unsoiled cloth. The wetting and water retention of soiled cloth improved with addition of surfactants, whereas water retention ratio(W/H) values didnot change markedly. Generally surfactants with low surface tension and high HLB (Hydrophile-lipophile balance) were more effective in improving the wetting/retention properties of soiled cloth. Nonionic surfactants having high ethylene oxide contents of 20 moles; i.e., Tween 20, 40, 60 & 80, showed better detergency than low ethylene oxide contents of 4 moles; i.e., Tween 21, 61 & 81. As HLB values of surfactants and $cos{\theta}$ of the soiled cloth increase, the detergency values of soiled cloth increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.116-122
• /
• 1999

According to the stringent exhaust emission regulation, precise control of air fuel ratio is one of the most important issues on gasoline engine. Although many researches have been carried out to identify the fuel transport phenomena in a port fueled gasoline engine, complexity of fuel film behavior in the intake port makes it difficult. The fuel film behavior was investigated recently by using visualization method and these gave us qualitative understanding. The purpose of this study is to estimate of wall wetting fuel in the intake port and the inducted fuel mass was predicted by using wall wetting fuel model . The model coefficient($\alpha$,$\beta$) and fuel film mass on the port wall were determined from measured in-cylinder HC concentration using FRFID after injection off. The fuel film mass was increased, but $\alpha$(ratio of directly inducted fuel mass into cylinder from injected fuel mass) was decreased with increasing load at the same engine speed. $\beta$is nearly constant value(0.8~0.9). when injected fuel mass is varied at 1500rpm , the calculated air fuel ratio using well wetting fuel model was nearly the same as measured by UEGO.

• Korean Journal of Metals and Materials
• /
• v.47 no.6
• /
• pp.383-390
• /
• 2009

The effects that processing atmospheres and alloy composition have on the wetting characteristics of Al-Mg alloys on the $SiO_{2}$ substrate were investigated by measuring the wetting angles. It was observed that the wetting behavior of the Al-Mg alloys on the $SiO_{2}$ substrate vary depending on the Mg content of the alloys and atmospheres. The results showed that the contact angle decreases with increasing Mg content, angle is generally larger in the $N_{2}$ atmosphere than in the Ar atmosphere. We discussed the validity of the results obtained from the wetting test on the basis of recent theories and the results observed from the actual penetration tests.