• Journal of Welding and Joining
• /
• v.35 no.1
• /
• pp.74-78
• /
• 2017

In auto ancillary fabrication industry, GMAW is a very useful & important welding process and EN10025 S 235 Grade is common material used for manufacturing of two wheeler chassis. This research gives the detail influence of welding process parameters such as welding current, welding voltage, wire speed on the penetration in EN10025 S 235 Grade mild steel material. The experimentation of this research has been carried out by using three factors, three level Taguchi DOE method. To analyze & optimize the welding parameters & characteristics, analysis of variance, L9 orthogonal array & signal to noise ratio are used. Length of Penetration in addition to the depth of penetration is major concern in fillet welded joints, as the penetration decides the strength of the welded joint. After analysis of penetration in all 9 welded samples, optimize parameters readings verified & found probability value within 0.05.From this research it is come to know that welding current & welding voltage is major parameters which affects the penetration in welded joints.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.28-34
• /
• 2010

This paper was described on investigation to prevent porosity in high speed MIG Welding of Al 6082-T6. Porosity measurement was carried out by using image analysis of micrographs with the help of an analysis software. The main parameter was arc length and torch progressive angle. The porosity ratio was increased as arc length was increased. The arc length was increased depending upon the output voltage. By proper selection of pulse waveform parameter, the stable arc of one pulse one drop was generated. The porosity ratio of optimum condition in one pulse one drop was lower than high voltage condition. When torch progressive angle was an angle of advance $10^{\circ}$, porosity ratio was minium.

• Journal of Welding and Joining
• /
• v.6 no.2
• /
• pp.47-55
• /
• 1988

This paper reports on a study of the influence of welding variables on the weld shape of Al-7020 in pulse-GMA welding. Five variables, i.e., wire feed rate, peak pulse current, welding speed, welding votage, and pulse frequency were investigated for their effects on the weld shape. From the results of the 2$^{n-1}$ fractional factorial design, quantitative effects of each variable and the interaction of two variables were obtained, and consequently wire feed rate, welding voltage, and welding speed were determined as the main welding variables. Supplementary experiment was performed for ivestigating the detailed relationship between the main variables nd the seld shape. In this experiment, the penetation of the seldment increased when the wire feed rate was raised, nad the bead width increased when the welding voltage was raised or the welding speed was reduced.d.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.6
• /
• pp.473-479
• /
• 2019

Welding is one of the most popular joining methods and most welding quality estimation methods are executed using joined material. This paper propose welding quality estimation methods using dynamic current, voltage and resistance which are obtained during welding in real time. There are many kinds of welding method. Among them, we focused on the projection welding and gathered dynamic characteristics from two different types of projection welding. For image learning, graphs are drawn using obtained current, voltage and resistance, and the graphs are converted to images. The images are labeled with two sub-categories - normal and defect. For deep learning of images obtained from welding, Convolutional Neural Network (CNN) is applied, and Tensorflow was used as a framework for deep learning. With two resistance welding test datasets, we conclude that the Convolutional Neural Network helps in predicting the welding quality.

• Journal of Welding and Joining
• /
• v.22 no.1
• /
• pp.58-64
• /
• 2004

The control of the weld bead shape is important in laser welding of the small parts. The effects of laser welding parameters on the weld bead shape in the pulsed Nd:YAG laser welding of STS 304L material were investigated. Shielding gas type, flow rate, pumping voltage, pulse frequency, pulse width, focal position and overlap distance were selected as laser welding parameters. Experiments were designed and conducted using the Taguchi method which was a statistical experimental method. The weld bead width, penetration, area and aspect ratio were measured and analysed as the weld bead shape properties and the welding parameters were optimized to maximize the weld aspect ratio. Weld aspect ratio were greatly affected by the pulse width, pumping voltage and pulse frequency, and somewhat by the overlap distance, and little by the shielding gas type, flow rate and focal position. A confirmation experiment were conducted using the optimized welding parameters.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.115-117
• /
• 2004

Nd:YAG laser welding system was used to manufacture instrumented irradiation fuel. The optimal condition of zircaloy-4 seal tube is charge voltage 180V and pulse per energy 51. We got good welding result in charge voltage 400V, pulse width 7ms, pulse frequency 5 in zircaloy-4 endcap welding.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.65-67
• /
• 2002

The gas metal arc welding(GMAW) is regarded as one of the best candidate for welding automation in industrial joining application. It is important to monitor the weld quality for the high performance of weld automation. The measured analog signal is frequency analyzed by digital signal process method. In order to observe the welding phenomena and control welding condition, arc light, voltage, and current are measured at the same time. They are analyzed and compared with arc sound. for these experiments, a power source of constant voltage characteristics was used in the pure metal transfer mode.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.35-40
• /
• 2014

The contact tip for gas metal arc welding has important functions to transmit the welding current to the wire and to guide the wire to molten pool. If the contact tip is damaged, it is a cause of lowering the welding productivity due to removal of welding defects and replacement of contact tip. In case of the use of a contact tip for a long time the arc is unstable because the processed hole in the contact tip center is larger, and the variation of aiming position of the welding wire causes a seam tracking error. In this study, gas metal arc welding experiments using contact tip of three different materials were performed. The contact tips with Cu-P, Cu-Cr, and Cu-ODS were used at the experiments, and the welding characteristics by each contact tip were evaluated. After welding contact tip appearance, welding spatter adhesion amount of the nozzle, and weld bead appearance were evaluated. The welding current and welding voltage were measured to verify arc stability during arc welding.

• Journal of Welding and Joining
• /
• v.8 no.1
• /
• pp.31-42
• /
• 1990

Arc must be stable during welding first of all other factors for obtaining sound weldment, especially in the automation of welding process. Arc stability is somewhat sophisticated phenomenon which is not clearly defined yet. In consumable electrode welding, the voltage and current variation due to metal transfer enables to assess arc stability. Recently, statistical analyses of the voltage and current waveform factors are performed to assess the degress of arc stability which is assessed and controlled by operator's own experience by now. But, considering the increasing need and the trend of automation of welding process, it is necessary to monitor arc stability in real-time. In this sutdy, the modified stability index composed of two voltage and current wvaeform factors (arc time and short circuit time) reduced from four factors (arc time, short circuit time, average arc current and average short circuit current) in Mita's index by the welding electrical circuit modeling is proposed and verified by experiments to be well estimating arc stability in the static sense. Also, the recursive calculation form estimating present arc stability in the dynamic sense is developed for real-time estimation. The results of applying the recursive index during welding show good estimation of arc stability in real-time. Therefore, the results of this study offers the mean for real-time control arc stability.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.133-138
• /
• 2019

This study evaluated the tensile properties of SAPH440, a hot-rolled steel for automotive structural applications, based on GMAW lap welding, the welding current, the welding voltage, and the feed rate. Tensile tests were performed according to the joint parameters of the GMAW process, for which specimens were fabricated according to KS B ISO 9018 by lap welding. The bead appearance was observed in each condition, and the weldability was evaluated by the tensile test. Higher the welding current resulted in a deeper weld, but the tensile strength was not significantly different from when the parameter was fixed due to the fracture of the base material. When the current was higher than the voltage, as in the case of a welding current of 200 A and welding voltage of 17 V, a large amount of spatter is generated, the welding is unstable, and the welded part breaks. Higher the voltage resulted in the bead not causing defects in general, and it also affected the weldability. If the current and voltage were too low, the welding was not performed normally, and the tensile strength could not be measured. However, as the current increased, the increase of the voltage and the feed rate did not affect the tensile strength.