• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.127-133
• /
• 2002

In this study, metal transfer characteristics in pulsed current metal inert gas (MIG) welding of aluminum was investigated. Based on the metal transfer characteristics from direct current electrode negative MIG welding, the one drop per one pulse(ODOP) condition was predicted and compared with experimental data. The results indicated that experimental pulse range for the ODOP condition is wider than that predicted from the DCEP MIG welding data. In addition, more stable metal trnasfer behavior was obtained at the higher end of the ODOP condition.

• Proceedings of the KWS Conference
• /
• 1994.05a
• /
• pp.157-160
• /
• 1994

Characteristics of laterally bonded tri-metal sheets (stainless steel/Invar/stainless steel) fabricated by laser beam welding are compared to those of samples by Imphy and Hitachi Co-operations. Residual stess of tri-metal is calculated by using of the hole-drilling stain gauge method. The aging effect of stainless steel strip on welding is also discussed. In addition to, a numerical approach for laser beam welding is tried. Finally, laser beam welding system of tri-metal can be designed on th basis of experimental and theoretical results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1240-1247
• /
• 2008

Leakage trouble on the sea water pipeline in engine room is often resulted from a localized corrosion due to severe corrosive environment caused by both high speed and high pressure of sea water flowing through the inner pipe. In addition, when the ship is in stand-by or emergency condition, underwater welding to control the leakage of sea water from a hole of its pipe is very important in an industrial safety point of view. In this study possibility of underwater welding to control leakage of sea water and corrosion property of its welding zone were investigated with the electrochemical methods by parameters of welding methods and welding electrodes when underwater welding is achieved with a such case that sea water is being leaked out with a height at 50mm from a hole of $2.5mm{\emptyset}$ of test pipe. Corrosion resistance of weld metal zone is better than the base metal and its hardness is higher than that of the base metal. However corrosion potential of weld metal zone showed a negative value than that of the base metal, therefore weld metal zone is preferentially corroded rather than the base metal by performance of galvanic cell due to difference of corrosion potential between weld metal zone and base metal. Eventually it is suggested that leakage of sea water is successfully controlled by underwater welding,

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.35-40
• /
• 2014

The contact tip for gas metal arc welding has important functions to transmit the welding current to the wire and to guide the wire to molten pool. If the contact tip is damaged, it is a cause of lowering the welding productivity due to removal of welding defects and replacement of contact tip. In case of the use of a contact tip for a long time the arc is unstable because the processed hole in the contact tip center is larger, and the variation of aiming position of the welding wire causes a seam tracking error. In this study, gas metal arc welding experiments using contact tip of three different materials were performed. The contact tips with Cu-P, Cu-Cr, and Cu-ODS were used at the experiments, and the welding characteristics by each contact tip were evaluated. After welding contact tip appearance, welding spatter adhesion amount of the nozzle, and weld bead appearance were evaluated. The welding current and welding voltage were measured to verify arc stability during arc welding.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.4
• /
• pp.334-340
• /
• 2016

The combustion chamber of a diesel engine is often exposed to a more serious wear and corrosion environment than other parts of the engine because its temperature increases as a result of using heavy oil of low quality. Therefore, repair and built-up welding methods must be performed on worn or corroded parts of the piston crown, exhaust valve, etc. from an economical point of view. In this study, Inconel 718 filler metal was used in repair welding on the groove of a forged steel specimen for a piston crown, along with built-up welding on the surface of another forged steel specimen. Then, the corrosion characteristics of the weld metal zone for the repair welding and the deposited metal zone for the built-up welding were investigated using electrochemical methods in a 35% H₂SO₄ solution. The deposited metal zone indicated better corrosion resistance than the weld metal zone, showing a nobler corrosion potential, higher impedance, and smaller corrosion current density. It is considered that metal elements with good corrosion resistance were generally included in the filler metal, and these elements were also greatly involved in the deposited meta by built-up welding, whereas the weld metal consisted of metal elements mixed with both the filler metal and base metal elements because of the molten pool produced by the repair welding. Finally, it is considered that the hardness of the weld metal was increased by the repair welding, whereas the built-up welding improved the corrosion resistance of the deposited metal.

• Journal of Welding and Joining
• /
• v.32 no.5
• /
• pp.7-12
• /
• 2014

In this study, API-X100 steel pipes were welded with various kinds of welding wires in the laser-arc hybrid welding process. 10kW fiber laser source was combined to MIG arc welding process. API X-100 steel of base metal was of 16.9mm thickness, and butt welding applied. After welding, full penetration weld was acquired by 1-pass welding. A root porosity and the lack of fusion was observed in some welding conditions. By the mixing the melted wire, acicular ferrite, polygonal ferrite, pro-eutectoid, aligned side plate, and bainite structures were observed at the weld metal. From the observation of hybrid weld, unmixed zone had more Ni and Cr. The unmixed zone was a 1/3 area of the weld metal. As the mechanical test of the hybrid welding, tensile test and impact test applied. From the tensile test, all of the welding except SM70S was fractured at the base metal. The result of the impact test at -30 degree C led 60J~320J of the absorbed energy. The result of the low-absorbed energy might be from the coarse equiaxed structures of the weld metal.

• Journal of Welding and Joining
• /
• v.22 no.2
• /
• pp.46-50
• /
• 2004

In today's highly competitive marketplace, it is of great significance for the manufacturing industry to reduce lead-time and costs fur the product development. Since first emerged in 1986, Rapid Prototyping (RP) technology has helped successfully to reduce time and costs. Recently, RP using functional materials such as metal has been researched. However RP using the molten metal has been struggling to resolve several drawbacks, such as dimensional inaccuracy, poor surface finish, post finishing, etc., that originate primarily from the overall deposition of molten metal for each layer. So, the purpose of this study is to develop a new RP technique using sheet metal and projection welding for reducing several drawbacks in occurring RP using molten metal. Also tensile and bending specimens were made by the developed RP process using projection welding and were verified.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.522-527
• /
• 2002

The microstructure and mechanical properties of friction stir welded OFC plates with 2mm in thickness were examined with the changing welding parameters such as welding speed, rotation speed in this study. The sounding welding conditions was acquired at the optimum welding conditions of the 41mm/min to 61mm/min of welding speed at 1250 rpm of rotation speed. The microstructure of weld zone was divided into four parts such as the base metal region (EM), thermal mechanical affected zone (TMAZ), heat affected zone (HAZ), stir zone (SZ). The grain size in the SZ and the width of weld nugget were increased with increasing welding speed. The hardness profiles of the base metal were distributed about 80HV. The HAZ is a slightly softened region of about 60~75 HV relative to the base metal. The hardness profiles of the SZ were higher than that of base metal. The tensile strength was increased with increasing welding speed. In case increasing rotation speed, tensile strength was decreased. The maximum tensile strength was about 220:MPa which was 110% of joint efficience of that of base metal at 41mm/min of welding speed, 1250rpm of rotation speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.2
• /
• pp.105-111
• /
• 2016

Ultrasonic metal welding, unlike the conventional welding techniques, does not require an external heat source, welding rod, or filler metal. Therefore, ultrasonic metal welding is not only economical but also environment-friendly, and hence, it has been receiving much attention. In ultrasonic welding, heat is generated because of the plastic deformation and the friction between both surfaces of the welded materials. It is important to identify the heat-affected zone by measuring the temperature generated at the weld. In this study, the effects of the welding pressure, welding time, and vibration amplitude on the temperature distribution in the weld were evaluated by performing a transient thermal analysis of the heat generated during ultrasonic metal welding. The experimental results indicated that the temperature of the weld tends to increase with the welding time and vibration amplitude. However, an increase in the pressure does not affect the temperature of the weld largely.

• Journal of Welding and Joining
• /
• v.20 no.3
• /
• pp.60-66
• /
• 2002

Almost every die fur automobiles must be corrected or remodeled for minor geometrical changes or for better hardness characteristics by arc welding process. Although many other kinds of arc welding processes have been automated with robots, this molten metal deposition process for die remodeling still depend entirely on experienced welders. In this study, the database for bead shapes with respect to welding parameters are constructed by experiments to automate the molten metal deposition by arc welding process. And the changes of welding parameters for inclined base metal are studied to consider the effect of die geometries fur the welding process.