• 한국구조물진단유지관리공학회 논문집
• /
• 제13권4호통권56호
• /
• pp.116-125
• /
• 2009

최근 건설 기술 발달에 따라 공기 단축을 위하여 세그먼트를 공장 제작하고 현장에서 용접 또는 볼팅 등의 방법으로 접합을 하는 시공이 이루어지고 있으며, 확대되고 있는 추세이다. 이때 강과 콘크리트로 구성된 합성부재의 용접시, 용접열이 약 20,000$^{\circ}C, 용접부 주변 온도가 1,300$^{\circ}C 이상이 될 정도로 높은 온도가 생성 된다. 이때 높은 온도로 인하여 용접부와 맞닿아 있는 콘크리트의 강도 감소가 발생하며, 경우에 따라서 국부적으로 강도감소가 매우 큰 곳도 존재하게 되어 구조물 거동에 영향을 미칠 수 있다. 본 연구에서는 이를 방지하기 위해 강재와 콘크리트 사이에 보강재를 삽입하여 용접열에 의한 콘크리트의 강도 감소를 방지하는 방법을 제시하였다.

• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.74-83
• /
• 2002

In order to investigate the hot cracking phenomena of the Inconel 690 overlay welds, the hot cracking test(modified Varestraint test) was performed by varying augmented strain and welding speed in GTAW. A total of five kinds of specimens was used in the hot cracking test. The specimens used were two kinds of one layer specimens that were composed of just Inconel 690 deposited metal and three kinds of double layer specimens that were composed with as upper part of Inconel 690 weld metal and lower part of SA508 cl.3 or STS 309L. The main results are as fo11ows: In the welds composed of just Inconel 690, as the augmented strain was more increased and the welding speed was more decreased, the extent of cracking was more increased. And these cracks were mainly solidification cracks, and liquation cracks were also observed partially in HAZ. And hot cracking susceptibily of Inconel 690 welds by using filler metals containing Nb were higher than that of the welds with Nb free. The hot cracking susceptibility of Inconel 690 weld metal was increased with dilution of SA 508 cl.3 and STS 309L, and the influence of SA 508 cl.3 was higher than that of 575 309L. The results of calculation of $TSC\Delta$ and $TLC\Delta$ in Inconel 690 weld metal changed by dilution with base metal or neighboring welds were agreed well with the results of hot cracking test in this study. Therefore, it was expected that the hot cracking was considerably decreased or prevented by using proper welding conditions such as lower heat input, filler metals, base metal and neighboring welds.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.482-487
• /
• 1993

A prediction method for determining the welding residual stress by artificial neural network is proposed. A three-dimensional transient thermomechanical analysis has been performed for the CO $_{2}$ Arc Welding using the finite element method. The validity of the above results is demonstrated by experimental elastic stress relief method which is called Holl Drilling Method. The first part of numarical analysis performs a three-dimensional transient heat transfer anslysis, and the second part then uses results of the first part and performs a three-dimensional transient thermo-clasto-plastic analysis to compute transient and residual stresses in the weld. Data from the finite element method were used to train a backpropagation neural network to predict residual stress. Architecturally, the finite element method were used to train a backpropagation voltage and the current, a hidden layer to accommodate failure mechanism mapping, and an output layer for residual stress. The trained network was then applied to the prediction of residual stress in the four specimens. The results of predicted residual stress have been very encouraging.

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.77-83
• /
• 2000

This study proposes the analysis and evaluation method of time series ultrasonic signal using the attractor analysis. Features extracted from time series signal analyze quantitatively characteristics of weld defects. For this purpose, analysis objective in this study is fractal dimension and attractor quadrant feature. Trajectory changes in the attractor indicated a substantial difference in fractal characteristics resulting from distance shifts such as parts of head and flange even though the types of defects are identified. These difference in characteristics of weld defects enables the evaluation of unique characteristics of defects in the weld zone. In quantitative fractal feature extraction, feature values of 3.848 in the case of part of head(crack) and 4.102 in the case of part of web(side hole) and 3.711 in the case of part of flange(crack) were proposed on the basis of fractal dimensions. Proposed attractor analysis and DAC in this study can enhance the precision rate of ultrasonic evaluation for defect signals of rail weld zone such as side hole and crack.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.665-672
• /
• 2013

With the development of advanced processing technology, laser processing systems, which require high-quality precision processing, have attracted considerable attention. Although laser equipment is expensive, it enables quick processing and less deformation of materials. This technology is often applied to secondary batteries, which has thus farinvolved the use of argon tungsten inert gas (TIG) welding. However, the welding characteristics of argon TIG welding are not yet good, and a laser is used for welding to address this problem. In this study, lap-joint welding was conducted, and the desired welding characteristics were obtained when the laser power was 1800W and the laser beam travel speed was 1.8 m/min. Lap-joint welding was conducted on Ni-coated SS41. Two cases were compared. No pores were observed in the Ni-coated SS41 lap-joint welding part, and cracks appeared from the lap-joints. Moreover, the pole rod and tap were welded together in a T-joint form to improve the output of the secondary battery. T-joint laser welding showed better welding characteristics than TIG welding.

• Journal of Welding and Joining
• /
• 제25권3호
• /
• pp.18-27
• /
• 2007

Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, ease of automation, single-pass thick section capability, enhanced design flexibility, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as the welding fur metals with CW Nd:YAG lasers. The bead-on-plate and Lap welding experiments are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the welding quality of the cross section, tensile stress behavior and the hardness of the welded part are investigated in comparison of the Nickel coated and Nickel uncoated S45C steel. As a result of experiment, nickel coated S45C Steel showed more even weld zone than Nickel uncoated counterpart upon lap welding. Also, it showed relatively small amount of internal defects and spatter, and Nickel coated S45C showed better weldability than Nickel uncoated S45C steel. The optimum welding process upon lap welding of Nickel coated S45C steel is when each laser power is 1900W; focal positions is -1mm; welding speed is $0.9{\sim}1.0m/min$. The heat input was $4.178{\sim}4.36{\times}103J/cm^2$.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.23-31
• /
• 2015

Stainless steel is used in automobile muffler and exhaust systems. However, in comparison with other steels it has a high thermal expansion rate and low thermal conductivity, and undergoes excessive thermal deformation after welding. To address this problem, we evaluated the use of arc brazing in place of welding for the processing of an exhaust system, and investigated the parameters that affect the joint characteristics. Muffler parts STS439 and hot-dipped Al coated steel were used as test specimens, and CuAl brazing wire was used as the filler metal for the cold metal transfer (CMT) welding machine, which is a low heat input arc welder. In addition, a Box-Behnken design of experiment was used, which is a response surface methodology. The main process parameters (current, speed, and torch angle) were used to determine the appropriate welding quality and the mechanical properties of the brazing part was evaluated at the optimal welding condition. The optimal processing condition for arc brazing was 135A current, 51cm/min speed and $74^{\circ}$ torch angle. The process was applied to an actual exhaust system muffler and the prototype was validated by thermal fatigue, thermal shock, and endurance limit tests.

• 한국산학기술학회논문지
• /
• 제7권3호
• /
• pp.298-307
• /
• 2006

본 논문에서 HDPE 관의 일체형 TEE성형 공정은 강소성 유한요소 해석 프로그램인 DEFORM-3D를 이용하여 해석을 하였다. 이중 보온관에서 외관으로 사용되는 HDPE 관은 관을 통하여 흐르는 온수의 온도를 유지하기 위한 관으로, TEE는 주관에 가지관을 연결하여 열의 수송방향을 바꾸는 역할을 한다. TEE제작에 압출 용접(Extrusion Welding)을 사용하는 기존의 방법으로는 이음부에서 강도가 취약한 문제점이 발생하기 때문에 HDPE 관을 성형시켜 TEE 형태로 일체화시킨 후에 맞대기 용접(Butt Welding)을 하는 방식을 제안하였다. 열간과 냉간 성형 실험을 실시하였고, 초기 구멍 형태에 따른 모델 파라미터가 강소성 유한요소해석에 의해 규명되어 졌으며, 이는 실제의 제품 제조 공정에 적용되어 졌다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.528-533
• /
• 2002

The mechanical and metallurgical properties of friction welded joints type 5052 Al alloy/A36 steel have been studied in this paper. The joint strength increased with increasing upset pressure and friction time till it reached the critical value. The joint strength was fixed at low strength compare to that of base metal in the case of increasing friction time. Microstructure of 5052 Al alloy was greatly deformed near the weld interface. The very fine and equaxied grain structure was observed at the near interface. The elongated grain was formed outside dynamic recrystallizatoin region at the peripheral part, while the A36 steel' side was not deformed. The hardness of the near interface was slightly softer than that of 5052 Al alloy base metal. The maximum softening width was about 8mm from the interface. In the present work, the friction welding condition, t$_1$=0.5sec, P$_2$=137.5MPa, showed a maximum joint strength (202MPa) when friction pressure, upset time and rotation speed were fixed at 75MPa, 5sec, 2000rev/min and these were the optimum friction welding condition of 5052Al/A36 steel joints.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.83-84
• /
• 2008

The primary water stress corrosion cracking (PWSCC) of dissimilar metal weld based on Alloy 82/182 is one of major issues in material degradation of nuclear components. It is well known that the crack initiation and growth due to PWSCC is influenced by material's susceptibility to PWSCC and distribution of welding residual stress. Therefore, modeling the welding residual stress is of interest in understanding crack formation and growth in dissimilar metal weld. Currently in Korea, a numerical round robin study is undertaken to provide guidance on the welding residual stress analysis of dissimilar metal weld. As a part of this effort, the present paper investigates distribution of welding resisual stress of a ferritic low alloy steel nozzle with dissimilar metal weld using Alloy 82/182. Two-dimensional thermo-mechanical finite element analyses are carried out to simulate multi-pass welding process on the basis of the detailed design and fabrication data. The present results are compared with those from other participants, and more works incorporating physical measurements are going to be performed to quantify the uncertainties relating to modelling assumptions.