• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.1-4
• /
• 2008

• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.27-33
• /
• 2005

Quantitative evaluation was performed on the microstructure of flux-cored arc(FCA) weld metal using a method blown as IIW scheme. It was mainly intended to figure out any practical difficulties in applying this method and also to provide the consumable makers with basic guide line in developing FCA welding consumables far better properties. Assessment of the experimental results showed IIW scheme was quite reliable in the low heat input range where the acicular ferrite was a major constituent. However, in the high heat input range, some scatter was noticed as the other phases like grain boundary ferrite and Widmansttaten ferrite become dominant. It implies that the accuracy of IIW scheme depends on the faction of microstructural constituents and it become worse as the fraction of latter two phases increases. This tendency was discussed in terms of the characteristics of those two phases. In addition, base line microstructure of rutile type FCA weld metal was addressed for developing new FCA welding consumables intended for higher heat input welding.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.141-143
• /
• 2004

The experimental simulation welds using 3kinds of 70ksi titania based flux-cored consumables were performed on 24 inches 24.6-thick API 5L Gr. B pipe with relatively high current, over 300A and four different Post Weld Heat Treaonent(PWHT) conditions at $625^{circ}C$ were applied to each consumable test coupon. It is well known that, in common welding processes such as Submerged Arc Welding(SAW) or Flux Cored A.c Welding(FCAW), the cooling rates in as-deposited weld bead are normally so ,apid that actual precipitation of microalloy carbonitrides, Nb(C,N) or V(C,N) is not likely to occur in the as-welded weld metal, however, during stress relief or PWHT the operation of precipitation can reduce the impact properties of the weld metal. As results of mechanical testing, it is concluded that PWHT at $625^{circ}C$ is detrimental to weld metal impact toughness of Ti-B type flux- cored (FC) welding consumables regardless of the amount of Nb and V, but two optima were exhibited, one at 800ppm Ti, 75ppm 5 and another 360ppm Ti, 54ppm 5.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.37-43
• /
• 2013

This study targets to make clear the connection between MS (Martensite start) point and welding shrinkage. We approved that a Martensite-transformed weldment may not yield state under low MS point, but also admitted the limitation of numerical calculation by inherent strain approach or thermal strain approach. Therefore, new thermal strain formulae during cooling stages were made. As a thermal strain is obtained by integrating thermal extension coefficient, a constant of integration should be decided. In our suggested formulae, the origin was based on totally remained austenite, and added strain from volume changes in Martensite transformation was based on totally transformed ferrite. Through the suggested methodology, It is verified that an MS point under a critical temperature can let weld shrinkage relax and the critical value can be obtained. For supporting this process, 15 weld-consumables were made, were tested by fillet type and were measured. As a result, a positive correlation between MS point and level of weld-distortion was obtained, but it was rather weak.

• Journal of Welding and Joining
• /
• v.16 no.1
• /
• pp.25-37
• /
• 1998

본 해설에서는 Inconel계와 Hastelloy계로 구분되는 9%Ni강용 피복아크용접봉을 중심으로 LNG저장탱크 용접시공시 발생 가능한 문제점들을 검토하고, Ni합금 피복봉의 심선과 피복제와 관련한 일반적인 제조특성을 살펴보았다. 또한 현재 국내 현장에서 용접시공에 사용되는 용접재료의 화학적, 기계적 특성과 함께 용접작업성을 평가한 결과 이들 피복아크용접봉들은 규격이 정한 요구조건들을 만족하면서 비교적 양호한 용접작업성을 확보하고 있는 것으롤 판단되었다. 이상의 검토결과는 향후 9%Ni강용 Ni합금 피복아크용접봉의 국산화 개발에 기초자료로 활용될 것으로 기대된다.

• Journal of Environmental Health Sciences
• /
• v.30 no.4
• /
• pp.320-328
• /
• 2004

A number of health hazards are generated in welding processes. In this paper, the characteristics of fumes and some other hazardous agents in welding are reviewed. Fumes in welding are generated by complex mechanism like physical ejection of particles, oxidation-enhanced vaporization, vaporization-condensation-oxidation, and spatter contribution. Fume generation rates could be described as a power function in a given process. Most of fume constituents was originated from consumables rather than base metal. The mass distribution for the welding fumes is unimodal and very small to penetrate respiratory system. So, almost fractions of fumes are classified into the respirable particulate mass. Total chromium contents in FCAW were similar to those from SMAW whereas hexavalent chromium concentrations in fume were similar to those produced from MIG welding fume. Hexavalent chromium was mostly soluble which was similar to the characteristic solubility of fume hexavalent chromium from SMAW.

• Journal of Korean Society for Quality Management
• /
• v.21 no.2
• /
• pp.242-253
• /
• 1993

The interpretation of the reaction mechanism is significant to produce the high quality welds and understand the welding processes. This investigation is important for the design of welding consumables and the selection of welding process parameters to develop the high quality welds. The objective of this study is to investigate the effect of electrochemical reactions on the transfer of alloy elements between slag and weld metal during submerged arc welding During submerged arc welding weld metal composition is shown to be controlled by two reaction mechanisms in four reaction zones. The responsible reaction mechanisms are thermochemical and electrochemical reactions. The possible reaction sites are the melted electrode tip, the detached droplet, the hot weld pool immediately below the moving electrode, and the cooling and solidifying weld pool behind the moving electrode. The possible reactions in submerged arc welding at different zones of the process is schematically shown in Figure 1.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.418-424
• /
• 2002

Korean Fusion Reactor(KSTAR) system consists of a vacuum vessel, in-vessel components, cryostat, thermal shield, super-conducting magnets and magnet supporting structures. These systems are in the final stage of engineering design with the involvement of industrial manufacturers. The overall configuration and the detailed dimensions of the KSTAR structure have been determined and the first stage of manufacturing is progressing now. In this study, the fabrication and assembly sequence were evaluated in viewpoint of high strengthening joints and very high accuracy. Especially for this purpose, the special cleaning process and welding process were proposed for high strengthening austenitic stainless steel which shall be used at cryogenic temperature. The draft procedure qualification data for welding process are presented with precise welding data including special narrow groove design. For the cooling line attachment on the surface of inside wall of magnet structure case, Induction brazing technology is introduced with some special jigging system and some consumables.

• Journal of Power System Engineering
• /
• v.18 no.4
• /
• pp.85-90
• /
• 2014

In this paper, the transient thermal and residual stress analysis of the welding of 9% Ni steel plates using the FEA software ABAQUS are presented. The 9% Ni steel plates are welded manually with welding consumables of 70% Ni based Inconel type super-alloys (YAWATA WELD B (M)), producing a multi-pass/multi-layer butt weld. For these materials, temperature dependant mechanical and thermal material properties are used in the analysis. The back gouging is considered in welding process simulation. The FE thermal results are validated by comparing the real fusion profile and heat affected zone (HAZ). In addition, the continuous indentation test was conducted to measure the strength of base metal, HAZ and weld metal.

• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.35-45
• /
• 1990

Casting are widely used nodays as complicated and diversified forming materials due to its superior castability. However the welding of cast iron has not been accompaniced satisfactory resulting in an microstructure change happened in the heat affected zone (HAZ), especially the graphite are formed and shaped consecutively in the area and it has great impact on the crack occuring and growth together with martensite forming in this area. It case of gray cast iron welding, it is required for pre-heat treatment or specific welding consumables to restrain forming the martensite in the HAZ. In this study, by applying the plasma surface overlaid welding. Fe-Mn-Al steel powder has been used for improvement of anti-crackability in the HAZ and much attention has been paid to establish the overlaid welding method for gray cast iron so that optimum welding conditions may prevent the cracking. With our experiments, we have found that to prevent defects which may occur in the HAZ, the overlaid welding technique for gray cast iron has been developed.