• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.73-79
• /
• 2009

This present paper investigated the mechanical properties and the microstructures of each penetration shapes classifying the conduction shape area and the keyhole shape area about electron beam welded 120(T)mm thick plated aluminum 5052 112H. As a result the penetration depth is increased linearly according to the output power, but the aspect ratio is decreased after the regular output power. In the conduction shape area, the Heat affected zone is observed relatively wider than the keyhole shape area. In the material front surface of the welded specimen, the width is decreased but the width in the material rear surface is increased. After the measuring the Micro Vikers Hardness, it showed almost similar hardness range in all parts, and after testing the tensile strength, the ultimate tensile strength is similar to the ultimate tensile strength of the base material in all the specimens, also the fracture point was generated in the base materials of all the samples. In the result of the impact test, impact absorbed energy of the Keyhole shape area is turned up very high, and also shown up the effect about four times of fracture toughness comparing the base material. In the last result of observing the fractographs, typical ductile fraction is shown in each weld metal, and in the basic material, the dimple fraction is shown. The weld metals are shown that there are no other developments of any new chemical compound during the fastness melting and solidification.

• Corrosion Science and Technology
• /
• 제17권3호
• /
• pp.109-115
• /
• 2018

Electrical Resistance Welding (ERW) on a longitudinal seam-welded pipe has been extensively used in oil and gas pipelines. It is well known that the weld zone commonly suffers from grooving corrosion in ERW pipes. In this paper, the grooving corrosion performances of API X65 grade non-sour service (steel-A) and API X70 grade sour gas resistant (steel-B) steel electrical resistance welding pipelines were evaluated. The microstructure of the bondline is composed of coarse polygonal ferrite grains and several elongated pearlites. The elongated pattern is mainly concentrated in the center of the welded area. The grooving corrosion test and electrochemical polarization test were conducted to study the corrosion behavior of the given materials. A V-shaped corrosion groove was found at the center of the fusion zone in both the steel-A and steel-B ERW pipes, as the corrosion rate of the bondlines is higher than that of the base metal. Furthermore, the higher volume fraction of pearlite at the bondline was responsible for the higher corrosion rate at the bondline of both types of steel.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.57-57
• /
• 2010

For thin panel welded structure, the various welding distortions were found due to the low resistance against welding deformation. Especially, buckling distortion induced in the thin panel welded structure produce severe problems related to cost in production stage and safety in service life. So, many researches including mechanical and thermal tensioning method for preventing the occurrence of buckling distortion in the production stage have been performed. The purpose of this study is to identify the behavior of longitudinal residual stress at the SA butt weldment with thin plate of 6mm thickness under tension load by 3 dimensional FEA. For it, mesh design for 3D FEA was constructed with 20 nodes brick element for butt weldment and 8 nodes shell element for base metal. According to FEA results, the longitudinal compressive strain inducing tensile residual stress at the butt weldment decreased. It was because the compressive thermal strain in way of weldment was reduced by tension load. The control effect of residual stress increased with an increase in tension load. So, if the amount of tension load applied to the weldment exceeds 1.5 times of longitudinal shrinkage force, the amount of longitudinal residual stress decreased below the critical value inducing the buckling distortion at the SA butt weldment. Its validity was verified by experiment.

• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.95-101
• /
• 2014

Joining of grey cast iron by fusion welding has much difficulties for its extremely low ductility and low toughness because of the flake form of the graphite. And the brittle microstructure, i.e. ledeburite may be formed during fusion welding by its rapid cooling rates. By these kinds of welding problem, preheat and post heat treatment temperature must be increased to avoid weld crack or welding problems. In order to avoid these fusion welding problem, friction welding of cast iron was carried out for improving joint soundness, establishing friction welding variables. There is no factor for evaluating friction weldability in continuous drive type friction welding. In this point of view, this study proposed the parameters for calculating friction weld heat input. The results obtained are as follows ; 1. There was a close relationship between tensile strength and flash appearance of friction welded joint. 2. Tensile strength was decreased and flash was severely oxidized as increasing frictional heating time. 3. As increased forging pressure $P_2$, flash had a large crack and tensile strength was decreased. 4. As powdered graphite by rotational frictional force induced flat surface and hindered plastic flow of metal, tensile strength of welded joint was decreased. 5. Heat input for continuous drive type friction welding could be calculated by the factors of $P_1$, $P_2$ and upset distance(${\delta}$).

• 한국가스학회지
• /
• 제5권3호
• /
• pp.15-22
• /
• 2001

세계적으로 천연가스의 사용은 높은 효율을 가진 청정에너지로서의 장점으로 인하여 꾸준히 증가하는 추세이며, 국내에서도 급격한 경제규모의 증대와 함께 사용량이 증가하고 있다. 천연가스 배관 용접부는 금속학적 및 역학적으로 파괴에 영향을 미치는 인자들을 다양하게 가지고 있는데, 이들 인자들에 의하여 파괴역학적 인성의 열화가 발생함과 동시에 파괴시험 결과의 해석에 많은 어려움이 유발된다. 본 연구에서는 우선 국내 천연가스의 주 배관으로 사용되고 있는 API 5L X65 등급의 고장력강 용접부의 파괴역학적 안전성을 평가하기 위한 목적으로, 실제 원주 용접부와 심 용접부의 파괴인성 시험을 수행하여 미세조직의 변화를 중심으로 미시적 혹은 거시적인 관점에서의 금속학적 인자가 파괴인성에 미치는 영향에 대해 평가하였다.

• 대한기계학회논문집A
• /
• 제38권12호
• /
• pp.1317-1323
• /
• 2014

본 연구의 목적은 마찰교반용접된 Al7075-T651의 피로균열전파 거동에 미치는 시험편의 채취방향의 영향을 고찰하기 위한 것이다. 피로균열전파 실험은 마찰교반용접된 공시재로부터 모재와 용접재에 대하여 CT 시험편을 채취하여 일정응력확대계수범위 제어하에서 수행되었다. 균열이 용접선에 수직하여 전파하는 것(TL 시험편으로 명명)과 균열이 용접선과 나란히 전파하는 시험편(LT 시험편으로 명명)에 대하여 3가지 다른 응력확대계수범위에서 실험이 수행되었다. 시험편의 채취 방향에 따라 피로균열전파거동에 주요한 영향을 미침을 알 수 있었다. Paris 법칙에 적합시킨 결과 지수 m값은 WM-LT 시험편이 3.56으로 가장 높게 나타났다.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.97-103
• /
• 1999

Ships, structures on the ocean, bridges, and other structures tend to be large by the development of industry. These ultra thick plate were welded with large heat input, which causes welding stresses, deformation and buckling, so it has to be considered the weld design, safety, reliability. The welded residual stresses were produced and redistributed due to the effect of large heat input. The mechanical phenomenon has not been surely identified yet. In spite of the lack of the study on the box column, there are various types of steel frame such as I type, H type, + type and $\bigcirc$ type, used in high story building. In this study, we performed computer simulation with two dimensional heat conduction and plane deformation thermal elasto-plastic finite element computer program as changing the plate thickness to 100mm, 150mm and groove angle to $60^{\circ}C$, $45^{\circ}C$, $30^{\circ}C$ of corner joint in box column. And then, to identify mechanical phenomenon such as the phenomenon of thermal distribution, welding residual stresses and deformation and to decide optimum groove angle and welding condition. The main conclusion can be summarized as follows: 1) Since the groove angle has became cooling down rapidly due to its smaller value, the temperature slope was steeped somewhat. 2) The tensile stress within the welding direction stresses was somewhat decreased at the weld metal and HAZ, increasing of the groove angle. 3) The local stress concentration of the groove angle $60^{\circ}C$ was appeared smaller than groove angle $30^{\circ}$.

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1379-1386
• /
• 2013

본 논문에서는 용접부 중앙에 원주방향 관통균열이 있는 V-그루브 맞대기 용접 배관의 한계하중 해석을 수행하였다. V-그루브 맞대기 용접 배관이 그루브 각 $45^{\circ}$, $90^{\circ}$를 갖는 형상에 대한 한계하중 식을 제시하기 위해 용접 형상의 변화에 따른 용접부 너비를 정의하였고 강도불일치 비, 용접부 너비, 균열 길이 및 배관 반경 비에 대한 체계적인 변수 해석을 수행 하였다. 모재와 용접재는 탄성 완전소성재료로 가정하였으며 상불일치와 하불일치 조건에서의 인장 하중과 굽힘 하중에 대한 강도불일치 한계하중이 강도불일치 비($M_F$)와 형상변수(${\psi}$)를 통해 정량화 됨을 유한요소 해석을 통해 확인하였다.

• International Journal of Automotive Technology
• /
• 제5권1호
• /
• pp.55-59
• /
• 2004

Spot welding is a very important and useful technology in fabrication of thin sheet structures such as the parts in an automobile. However, because the fatigue strength of the spot welding point is considerably lower than that of the base metal due to stress concentration at the nugget edge, the nugget size must be estimated to evaluate a reasonable fatigue strength at a spot welded lap joint. So far, many investigators have experimentally studied the estimation of fatigue strengths of various spot weldments by using a destructive method. However, these destructive methods poses problems so testing of weldments by these methods are difficult. Furthermore, these methods cannot be applied to a real product, and are time and cost consuming, as well. Therefore, there has been a strong, continual demand for the development of a nondestructive method for estimating nugget size. In this study, the effective nugget size in spot weldments have been analyzed by using thermoelastic stress analysis adopting infrared thermography. Using the results of the temperature distribution obtained by analysis of the infared stress due to adiabatic heat expansion under sinusoidal wave stresses, the effective nugget size in spot welded specimens were estimated. To examine the evaluated effective nugget size in spot weldments, it was compared with the results of microstructure observation from a 5％ Nital etching test.

• 한국전산구조공학회논문집
• /
• 제22권6호
• /
• pp.541-548
• /
• 2009

본 논문은 샤르피 충격실험과 유한요소법를 이용하여 노치위치에 따른 파괴거동과 흡수에너지의 영향을 평가하였다. 본 연구자는 쉴드메탈아크 용접방법으로 두께가 25mm인 압력용기용강(SA-516 Gr. 70)을 용접하였고, 이 용접된 평판으로 샤르피 시편을 제작하였다. 샤르피 충격실험에서는 용접열영향부(HAZ)에서 노치위치가 다른 시편이 사용되었다. 그리고 본 연구자는 유한요소법을 이용하여 샤르피 충격실험에서의 균열진전을 모사하였다. 용접열영향부(HAZ)의 기계적 물성을 유한요소해석에 적용하기 위해 HAZ를 2개 영역, 3개 영역 그리고 4개 영역으로 나누었다. 본 연구결과에서는 샤르피 충격실험의 흡수에너지가 노치위치에 의존적이라는 것을 보여주었다. 또한 샤르피 용접시편에서 신뢰성 있는 유한요소해석 결과를 얻기 위해서는 용접열영향부를 적어도 3개 이상의 영역으로 나누어야 한다는 결과를 얻었다.