• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.27-34
• /
• 1988

The objective of this paper is to investigate the effect of residual stress on fatigue crack growth behavior. For this purpose, submerged arc welding was performed on SM50A steel plate and post weld heta treatment (PWHT) was followed. Residual stress distribution on the weld plate was determined by a hole drilling method and a series of .DELTA.P-const. and .DELTA.K-decreasing fatigue test were performed on the three different regions, i.e. weld metal, HAZ and base metla. Following conclusins were achieved. 1. In "as welded" specimens, tensile residual stresses were produced in the center portion of the specimen while compressive residual stresses were produced near the edges. In PWHT specimens, however, most of the residual stresses were disappeared. 2. The fatigue crack growth behavior in low .DELTA.K region was considerably affected by the presence of residual stress in both "as welded" and PWHT specimens. 3. Because of the relaxation of residual stresses in PWHT condition, the values of m increased from 2.62-2.78 (in the "as welded" condition) to 3.57-3.91 (in the "PWHT" condition)3.91 (in the "PWHT" condition)condition)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1311-1316
• /
• 2010

In this study, straight slot welding was carried out using a 316L stainless steel test block, and numerical simulation of the slot weld process was performed using finite element analysis. Data on the residual stress were obtained at equally spaced points on the top surface of the test block along directions parallel and perpendicular to the welding direction. After electrolytic polishing of the top surface of the block, the residual stress was measured by the X-ray diffraction method. The calculated weld residual stresses were compared with the measured data, and they were in good agreement with the data. The weld residual stress distribution inside the plate was determined from the results of finite element analysis, and the characteristics of the distribution were discussed in detail in this paper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.79-83
• /
• 2010

The conventional welding technique such as shield metal arc welding has been mostly applied to the piping system of the nuclear power plants. It is well known that this welding technique causes the overheating and welding defects due to the large groove angle of weld. On the other hand, the narrow gap welding(NGW) technique has many merits, for instance, the reduction of welding time, the shrinkage of weld and the small deformation of the weld due to the small groove angle and welding bead width comparing with the conventional welds. These characteristics of NGW affect the deformation behavior and the distribution of welding residual stress of NGW, thus it is believed that the residual stress results obtained from conventional welding procedure may not be applied to structural integrity evaluation of NGW. In this paper, the welding residual stress of NGW was predicted using the nonlinear finite element analysis to simulate the thermal and mechanical effects of the NGW. The present results can be used as the important information to perform the flaw evaluation and to improve the weld procedure of NGW.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.496-503
• /
• 2007

Although weld-induced deformation is inevitable in shipbuilding, it is important to reduce it as low as possible during fabrication for a more efficient production of ships' blocks. The weld-induced deformation is more serious in thin plates than in thick plates because heat affect zone of thin plates is wider than that of thick plates, and in addition internal and external constraints much more influence upon weld-induced deformation of thin plates. This paper deals with the application of the mechanical tensioning method to butt weld of thin plates to reduce the transverse and longitudinal deformation. in order to investigate the quantitative effect of tensioning method upon the reduction of angular deformation and shrinkage in longitudinal and transverse direction of weld line, butt welding test have been carried out for several thin plate specimens with varying plate thickness and magnitude of tensile load. Numerical simulation has been also carried out to compare the weld-induced deformation and residual stress. From the present study, it has been found that the tensioning method is very effective on reduction of weld-induced residual stress as well as weld-induced deformation.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.1
• /
• pp.64-69
• /
• 2008

As it has been well appreciated from the viewpoint of efficiency, The weld-induced deformation control is one of the most important issues in marine structure production. In the case of thin plate block, weld-induced deformation is more serious than in the case of relatively thick plate block. The heat affect zone of thin plates is wider than that of thick plates with the same heat input. Among weld-induced deformations, the buckling deformation by the shrinkage and residual stress in the weld line direction is one of the most serious deformation types. This paper is concerned with controlling buckling deformations for the thin plate fillet welds, by using the tensioning method. A numerical analysis was carried out to illustrate several dominant buckling modes due to compressive residual stress in the fillet weldsof thin plates. Then, weld tests were carried out for 20 specimens with varying plate thickness, and with different magnitudes and directions for the tension load. The results graphically represented to shaw the effect of the tensioning method in reducing the weld-induced deformation. From the present findings, it was seen that the tensioning method is a useful way to control weld-induced deformations in the fillet welds of thin plates.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.2 s.75
• /
• pp.243-251
• /
• 2005

The fracture mechanics analysis of a crack in a weld must consider residual stress generated during welding. The standard definition of the J-integral requires a path dependent value in the presence of a residual stress field. Therefore, it is necessary to develop a path independent J-integral definition for a crack in a residual stress field. This paper addresses the modification of the Rice-J-integral to produce a path- independent J-integral when residual stresses and external forces are present. The residual stress problem is treated as an initial strain problem and the J-integral proposed for this type of problems is used. A program which can evaluate the J-integral for a crack in a weld is developed using the proposed J-integral definition. The situation when only residual stress is present is examined as is the case when mechanical stresses are applied in conjunction with a residual stress.

• Journal of Welding and Joining
• /
• v.27 no.4
• /
• pp.32-37
• /
• 2009

Alloy 600 and Alloy 82/182 materials have been used widely in PWR plants. But these materials are known to be susceptible to PWSCC(Primary Water Stress Corrosion Cracking). Recently, there have been several PWSCC events in major components due to repair welding, because repair welding in the dissimilar metal welds during the construction increases residual stress significantly on the inner surface of welds. In this paper, various residual stress analyses for repair welding were performed using FEM to check the effect of repair welding on residual stress distributions in PZR safety/relief nozzle. The results indicate that for inside surface repair welding, high tensile residual stress is developed on the inside surface of the nozzles.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.116-123
• /
• 2008

In the fossil power plant, the reliability of the components which consist of the many welded parts depends on the quality of welding. The residual stress is occurred by the heat flux of high temperature during weld process. This decreases the mechanical properties as the strength of fatigue and fracture or causes the stress corrosion cracking and fatigue fracture. Especially, the accidents due to the residual stress occurred at the weld parts of high-temperature and high-pressure pipes and steam headers. Also, the residual stress of the welded part in the recently constructed power plants has been brought into relief as the cause of various accidents. The aim of this study is the measurement of the residual stress using the x-ray diffraction method. The merits of this are more accurate and applicable than other methods. The materials used for the study is P92 steel for the use of high temperature pipe on super critical condition. The variables of tests are the post-weld heat treatment, the surface roughness and the depth from the original surface. The test results were analyzed by the distributed characteristics of the full width at half maximum intensity (FWHM) in x-ray diffraction intensity curve and by the relation of hardness with FWHM.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.10
• /
• pp.1235-1239
• /
• 2012

Primary water stress corrosion cracking (PWSCC) has been observed around the weld region of control rod drive mechanism (CRDM) nozzles in nuclear power plants overseas. The weld has a J-shaped groove and it connects the CRDM nozzle with the reactor vessel upper head (RVUH). It is a dissimilar metal weld (DMW), because the CRDM is made of alloy 600 and the RVUH is made of carbon steel. In this study, finite element analysis (FEA) was performed to estimate the stress condition around the weld region. Generally, it is known that a high tensile region is more susceptible to PWSCC. FEA was performed as for the condition of welding, hydrostatic test and normal operation successively to observe how the residual stress changes due to plant condition. The FEA results show that a high tensile stress region is formed around the weld starting point on the inner surface and around the weld stop point on the outer surface.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.5 s.248
• /
• pp.602-608
• /
• 2006

Vehicle components such as lower control arm are usually affected by heat during the welding process. As a result, residual stress is generated, which has much effect on mechanical performances such as crashworthiness and durability. In this study, the residual stress in lower control arm has been measured by the x-ray diffraction method and been analyzed by finite element methods. Heat transfer during seam weld process has been calculated and used in calculating thermal deformation with temperature dependent material properties. High residual stress has been found at vertical wall both by measurement and simulation. The simulation also showed the residual stress re-distribution when the component is subjected to cyclic loading condition.