• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.248-259
• /
• 2021

This study examined the influence of post weld heat treatment (PWHT) conditions on corrosion behaviors of laser-welded super duplex stainless steel tube. Due to the high cooling rate of laser welding, the phase fraction of ferrite and austenite in the weld metal became unbalanced significantly. In addition, the Cr₂N particles were precipitated adjacent to the fusion line, which can be susceptible to the localized corrosion. On the other hand, the phase fraction in the weld metal was restored at a ratio of 5:5 when exposed to temperatures above 1060 ℃ during the post weld heat treatment. Nevertheless, the high beltline speed during the PWHT, leading to the insufficient cooling rate, caused a precipitation of σ phase at the interface between ferrite/austenite in both weld metal and base metal. This resulted in the severe corrosion damages and significant decrease in critical pitting temperature (CPT), which was even lower than that measured in as-welded condition. Moreover, the fraction of σ phase in the center region of post weld heat treated steel tube was obtained to be higher than in the surface region. These results suggest that the PWHT conditions for the steel tube should be optimized to ensure the high corrosion resistance by excluding the precipitation of σ phase even in center region.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1145-1146
• /
• 2010

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.26-35
• /
• 1999

On the laser weld production line, a slight alteration of the welding condition changes the bead size and the strength of the weldment. The measurement system is produced by using three photo-diodes for detection of the plasma and spatter signal in $CO_2$ laser welding. The relationship between the sensor signals of plasma or spatter and the bead shape, and the mechanism of the plasma and spatter were analyzed for the bead size estimation. The penetration depth and the bead width were estimated using the multiple regression analysis.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.867-868
• /
• 2004

The maximum width of HAZ of SA508치.3 steel produced by overlay RPV cladding was approximately 10 mm and it was composed of variety of microstructures with various grain size and precipitates. In addition, along the weld fusion line there formed a heavy carbide precipitation zone in the width of $20{\sim}30\;{\mu}m$. 2. As the specimen sampling position approached to the weld fusion line, the increase in yield and tensile strength was approximately 90 and 40 MPa, respectively. Meanwhile, the plastic fracture strain reduced from 14 to 8 percent. 3. The lowest SP energy and the highest ductile to brittle transition temperature in the HAZ were observed at the coarse- and fine-grained HAZ.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.3
• /
• pp.172-176
• /
• 2003

In this paper, we studied the effects of mold temperature on the microstructure of injection molded parts. The weld line decreases in length and width as mold temperature increases. We investigated the dimensional stability of the parts made of two kinds of resin(polypropylene and polystyrene) by varying the mold temperature. As the mold temperature is high, both the shrinkage ratio and the thickness difference for the PS parts decreases. But the observation of PP parts shows a tendency to increase. The easiness of cavity filling and transcription of the mold texture is improved as the mold temperature is high.

• Design & Manufacturing
• /
• v.14 no.2
• /
• pp.42-48
• /
• 2020

This study is on the injection molding analysis for the LED outdoor lighting top cover of one heat sink body type structure. Thermoplastic and thermosetting resins were applied to compare the thermal properties during the injection molding process. The thermoplastic resin is used in this study due to special characteristics that it is light, good strength and dose long not transmute quality even if pass long time. The thermosetting resin is applied to this study due to good in strength, lightweight and excellent etc, thermal conductivity. This study presented a preliminary analysis of fill time, weld line, air trap etc. for the injection molding process of LED lamp cover and body through simulation using Moldflow. As a result of the study, it was selected HTM-102 material because the thermosetting resin has excellent strength and heat conductivity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.713-716
• /
• 2000

In this study, we present a mobile robot for ultrasonic scanning of weldment. magnetic Caterpillar mechanism is selected in order to travel on the inclined surface and vertical wall. A motion control board and motor driver are developed to control four DC-servo motors. A virtual device driver is also developed for the purpose of communicating between the control board and a host PC with Dual 'port ram. To provide the mobile robot with stable and accurate movement, PID control algorithm is applied to the mobile robot control. And a vision system for detecting the weld-line are developed with laser slit beam as a light source. In the experiments, movement of the mobile robot is tested inclined on a surface and a vertical wall.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.4
• /
• pp.32-37
• /
• 2010

One of the most common engineering processes using plastics is the injection molding. In addition, plastics are utilized over the entire areas in our life including cars and home appliances among others for their characteristics with no deterioration even after a long time, as well as for their light weights in addition to their good durability. This paper aimed to minimize defects through prior analyses on the weld line, air traps, filling time, molding temperature and deformation patterns among others while carrying out interpretations on the cooling, filling and deformation in the injection process using the moldflow for rear lamp reflectors among components for a car in making parts through the coating process after injection.

• Korea-Australia Rheology Journal
• /
• v.18 no.1
• /
• pp.1-8
• /
• 2006

Blend of bisphenol-A polycarbonate (PC) and (acrylonitrile-styrene-acrylic rubber) terpolymer (ASA) having excellent balance in the interfacial properties and mechanical strength was developed for the automobile applications. Since interfacial adhesion between PC and styrne-acrylonitrile copolymer (SAN) matrix of ASA is not strong enough, two different types of compatibilizers, i.e, diblock copolymer composed of tetramethyl polycarbonate (TMPC) and SAN (TMPC-b-SAN) and poly(methyl methacrylate) (PMMA) were examined to improve interfacial adhesion between PC and SAN. TMPC-b-SAN was more effective than PMMA in increasing interfacial adhesion between PC and SAN matrix of ASA (or weld-line strength of PC/ASA blend). When blend composition was fixed, PC/ASA blends exhibited similar mechanical properties except impact strength and weld-line strength. Impact strength of PCI ASA blend at low temperature was influenced by rubber particle size and its morphology. PC/ASA blends containing commercially available PMMA as compatibilizer also exhibited excellent balance in mechanical properties and interfacial adhesion.

• Transactions of Materials Processing
• /
• v.12 no.8
• /
• pp.738-743
• /
• 2003

The major problems of a plastic injection mould can be devided into two kinds, one is in mould another in injected parts. Most of defects of the former comes from mould design, such as, structure and working. The latter are weld line, warpage, sink mark, burning, flow mark, scratching, shading, black hole and so on. Most of problems in injection molding are difficult to find the reason because of complexity. The purpose of this paper is to improve the quality of plastic injection mould and parts with inquiring the counter plan and analizing troubles of the part of Flat TV Front Cover by flow control method and gas-assisted injection moulding. For minimizing defects of the injection moulded parts, computer aided simulation method for injection mould filling was used. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality, such as minimizing surface defects of injection moulding parts and troubles in mould was achieved.