• 소성∙가공
• /
• 제13권8호
• /
• pp.678-688
• /
• 2004

The U-draw bending operation is known as a representative test method for springback evaluation of sheet metals since the sheet in U-draw bending operation undergoes stretching, bending and unbending deformations occurred at the stamping process. In this study, a simplified approach was proposed for predicting springback and side-wall curls of tailor-welded blank in U-draw bending operations, using moment-curvature relationships derived for sheets undergoing stretching, bending and unbending deformation. Two different welded strips were adopted to compare the effects of weld-line locations on the springback. One (type A) was welded along the centerline of the strip-width and the other (type B) was welded along the centerline of the strip-length. To investigate the effect of different thickness combination on the springback, the tailor-welded strips were joined by the laser welding process and consisted of three types of thickness combinations of sheets, SCP1 0.8t ＊ SCP1 1.2t, SCP1 0.8t ＊ SCP1 1.6t and SCP1 0.8t ＊ TRIP 1.0t. Some calculated results by the simplified formula were compared with experimental results.

• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.109-115
• /
• 2002

In this study high power Nd:YAG laser welding of structural steel was investigated. For the test steel blocks of $50{\times}50{\times}200mm$ were cut and machined, and bead-on-plate weld was made on the machined surface. Argon, nitrogen, helium, dry air or mixed gases were used to find the effect of shielding conditions on the bead formation. Results demonstrated that there were Fe I rich region and Fe II rich region in the laser induced plasma column based on the spectral analysis with S-2000 field spectrometer The Fe I region was located at the root of the column near keyhole opening. On the other hand, Fe II region was found at the middle of the plasma column. In the Nd:YAG laser welding, Fe I region emitted continuum which had peak value at wave length of around 710nm, and Fe II region had the peak at 580nm. In the welding of steel by $CO_2$ laser, however, no continuum was observed. There showed two groups of strong spikes in the $CO_2$ laser welding; the first group was displayed at the wave band of 450-560nm. This spike group emitted stronger intensity of light and sharper peaks than those group at 680-800nm.

• 대한기계학회논문집A
• /
• 제33권7호
• /
• pp.693-699
• /
• 2009

This paper shows mechanical properties and behaviors of macro- and micro-structures on friction stir welded specimen with 6061-T6 aluminum alloy plate. It apparently results in defect-free weld zone jointed at welding conditions like the traverse speed of 267mm/min, tool rotation speed of 2500rpm, pin inserted depth of 4.5mm and tilting angle of $2^{\circ}$ with tool dimensions such as tool pin diameter of 5mm, shoulder diameter of 15mm and pin length of 4.5mm. The tensile stress ${\sigma}_T=228MPa$ and the yield point ${\sigma}Y=141MPa$ are obtained at the condition of traverse speed of 267mm/min and tool rotation speed of 2500rpm. With the constant rotation speed, the higher traverse speed become, the higher tensile stress and yielding point become. Vickers hardness for welding zone profile were also presented.

• 소성∙가공
• /
• 제33권3호
• /
• pp.193-199
• /
• 2024

The friction welding characteristics of stainless steels, mainly used in energy and chemical plant industries due to its excellent corrosion resistance and high strength, was evaluated in this study. Friction welding was introduced and conducted at a rotation speed of 2,000 RPM, friction pressure of 30 MPa, burn-off length of 5 mm and upset pressure of 110 ~ 200 MPa on rod typed specimens. The grain boundary characteristics distributions such a grain size, shape, misorientation angle and kernel average misorientation of the welds were clarified by electron backscattering diffraction method. The application of friction welding on SUS304 alloy resulted in a significant refinement of the grain size in the weld zone (5.11 mm) compared to that of the base material (48.09 mm). The mechanical properties of the welds, on the other hand, appeared to be relatively low or similar to those of the base material, which were mainly caused by dislocation density in the initial material and grain refinement in the welds.

• 한국강구조학회 논문집
• /
• 제12권5호통권48호
• /
• pp.463-473
• /
• 2000

이 연구에서는 국내 피로설계규정상의 응력범주 C, D, E 및 E'에 해당하는 표준적인 구조인 십자 연결형, 면외거셋 부착형, 면내거셋 부착형 및 덮개판형을 모형화한 소형 시험편에 대한 피로실험을 실시하여 실험결과에 따라 각 시험편에 해당하는 국내 피로설계규정을 검증하며, 실험결과와 외국의 공개 데이터와의 비교 검토를 통해 국내 제작 강구조상세의 평가기준을 검토하였다. 실험 결과, AASHTO 및 JSSC, Eurocode의 관련 규정 값을 대부분 만족하는 것으로 확인되었다. 그러나, 십자연결형 접착부에 있어 모재가 파단된 하중전달형의 경우는 하중비전달형 보다 피로강도가 작으며, AASHTO 설계기준을 만족시키지 못하므로 설계기준에 대한 재검토가 필요할 것으로 판단된다. 한편, 요접부 길이의 영향은 면외거셋 에서 부착부 길이 80mm 시험편보다 150mm 시험편의 피로강도가 낮게 나타나 용접구조부 길이의 영향이 있음을 확인하였다. 실험결과들을 종합해보면, AASHTO 규정에 입각한 국내 시방서상의 피로규정을 대부분 만족하고 있으나, 보다 세분된 범주로 규정하고 있는 JSSC 및 Eurocode의 설계기준이 본 연구의 실험결과와 비교할 때 보다 합리적인 것으로 생각된다.

• 콘크리트학회논문집
• /
• 제19권4호
• /
• pp.411-420
• /
• 2007

본 연구는 반복 수평 하중을 받는 외부 보-기둥 접합부에서 작은 헤드를 사용한 headed bar의 사용성을 검증하기 위해 $90^{\circ}$ 표준갈고리로 정착한 실험체와 headed bar로 정착한 접합부 실험체를 제작하여 각각의 실험 결과를 비교하였다. 또한, headed bar 정착 성능에 영향을 주는 헤드 단면적, 단조 및 반복 가력 여부, 헤드와 보강근의 용접 여부등의 headed bar 인발 성능에 관한 영향을 구명하기 위한 인발실험을 병행하였다. 인발실험의 결과, headed bar의 인발강도는 헤드 면적 증가에 따라 증가하였고, 헤드와 보강근의 용접 유무, 가력 조건 (단조하중 및 반복하중)은 실험 결과에 큰 영향을 미치지 않는 것으로 나타났다. 외부 보-기둥 접합부 실험의 결과, $90^{\circ}$ 표준갈고리로 정착한 실험체와 headed bar로 정착한 실험체가 초기 균열, 균열의 발생 등 모두 거의 비슷한 양상이었으나, 최종 파괴 시에는 headed bar로 정착된 실험체가 $90^{\circ}$ 표준갈고리로 정착된 실험체에 비해 최대 강도 도달 이후 연성 거동, 연성비 및 변형 성능, 에너지소산 면적 등에서 우수한 거동을 보여주었다. 따라서 ACI 352 위원회의 설계지침을 따라서 제작된 접합부 상세와 동일한 조건으로 표준갈고리 대신 상대적으로 작은 headed bar를 사용할 수 있을 것으로 판단된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권1호
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• 한국강구조학회 논문집
• /
• 제29권4호
• /
• pp.303-310
• /
• 2017

WUF-W 접합부는 부재의 접합이 모두 용접으로 이루어진 접합부이며, 특수모멘트골조(SMF) 인증접합부 중 하나이다. 하지만 선행 연구들을 통해 일부 WUF-W 접합부 실험체가 4% 층간변위비의 특수모멘트골조(SMF) 요구성능을 만족하지 못하였으며, 이는 액세스 홀 형상과 연관이 있음이 보고되었다. 본 연구에서는 비선형 유한요소 해석을 이용하여 WUF-W 접합부의 요구성능을 만족하기 위한 주요 액세스홀 형상변수의 허용범위를 결정하였다. 또한 WUF-W 접합부 설계과정에서 주요 액세스 홀 형상변수의 타당성을 평가할 수 있는 간단한 경험식을 제안하였다.

• Steel and Composite Structures
• /
• 제27권3호
• /
• pp.337-353
• /
• 2018

In previous weak-axis moment connection tests, brittle fracture always initiated near the edge of the beam flange groove weld due to force flow towards the stiffer column flanges, which is the opposite pattern as strong-axis moment connections. As part of the China NSFC (51278061) study, this paper tested two full-scale novel weak-axis reduced beam section moment connections, including one exterior frame connection specimen SJ-1 under beam end monotonic loading and one interior frame joint specimen SJ-2 under column top cyclic loading. Test results showed that these two specimens were able to satisfy the demands of FEMA-267 (1995) or ANSI/AISC 341-10 (2010) without experiencing brittle fracture. A parametric analysis using the finite element software ABAQUS was carried out to better understand the cyclic performance of the novel weak-axis reduced beam section moment connections, and the influence of the distance between skin plate and reduced beam section, a, the length of the reduced beam section, b, and the cutting depth of the reduced beam section, c, on the cyclic performance was analyzed. It was found that increasing three parametric values reasonably is beneficial to forming beam plastic hinges, and increasing the parameter a is conducive to reducing stress concentration of beam flange groove welds while increasing the parameters b and c can only reduce the peak stress of beam flange groove welds. The rules recommended by FEMA350 (2000) are suitable for designing the proposed weak-axis RBS moment connection, and a proven calculation formulation is given to determine the thickness of skin plate, the key components in the proposed weak-axis connections. Based on the experimental and numerical results, a design procedure for the proposed weak-axis RBS moment connections was developed.

• Steel and Composite Structures
• /
• 제33권6호
• /
• pp.823-836
• /
• 2019

Spiral welded tubes (SWTs) are fabricated by helically bending a steel plate and welding the resulting abutting edges. The cost-effectiveness of concrete-filled steel tube (CFST) columns can be enhanced by utilising such SWTs rather than the more conventional longitudinal seam welded tubes. Even though the steel-concrete interface bond strength of such concrete-filled spiral-welded steel tubes (CF-SWSTs) is an important consideration in relation to ensuring composite behaviour of such elements, especially at connections, it has not been investigated in detail to date. CF-SWSTs warrant separate consideration of their bond behaviour to CFSTs of other tube types due to the distinct weld seam geometry and fabrication induced surface imperfection patterns of SWTs. To address this research gap, axial push-out tests on forty CF-SWSTs were carried out where the effects of tube material, outside diameter (D), outside diameter to wall thickness (D/t), length of the steel-concrete interface (L) and concrete strength grade (f'_c) were investigated. D, D/t and L/D values in the range 102-305 mm, 51-152.5 and 1.8-5.9 were considered while two nominal concrete grades, 20 MPa and 50 MPa, were used for the tests. The test results showed that the push-out bond strengths of CF-SWSTs of both mild-steel and stainless-steel were either similar to or greater than those of comparable CFSTs of other tube types. The bond strengths obtained experimentally for the tested CF-SWSTs, irrespective of the tube material type, were found to be well predicted by the guidelines contained in AISC-360.