• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.191-198
• /
• 2015

Objective : The purpose of this study was to conduct biomechanical analysis of varying backpack loads on the lower limb movements during downhill walking over $-20^{\circ}$ ramp. Method : Thirteen male university students (age: $23.5{\pm}2.1yrs$, height: $175.7{\pm}4.6cm$, weight: $651.9{\pm}55.5N$) who have no musculoskeletal disorder were recruited as the subjects. Each subject walked over $20^{\circ}$ ramp with four different backpack weights (0%, 10%, 20% and 30% of body weight) in random order at a speed of $1.0{\pm}0.1m/s$. Five digital camcorders and two force plates were used to obtain 3-d data and kinetics of the lower extremity. For each trial being analyzed, five critical instants were identified from the video recordings. Ground reaction force, loading rate, decay rate, and resultant joint moment of the ankle and the knee were determined by the inverse dynamics analysis. For each dependent variable, one-way ANOVA with repeated measures was used to determine whether there were significant differences among four different backpack weight conditions (p<.05). When a significant difference was found, post hoc analyses were performed using the contrast procedure. Results : The results of this study showed that the medio-lateral GRFs at RHC in 20% and 30% body weight were significantly greater than the corresponding value in 0% of body weight. A consistent increase in the vertical GRFs as backpack loads increased was observed. The valgus joint movement of the knee at RTO in 30% body weight was significantly greater than the corresponding values in 0% and 10% body weight. The increased valgus moment of 30% body weight observed in this phase was associated with decelerating and stabilizing effects on the knee joint. The results also showed that the extension and valgus joint moments of the knee were systematically affected by the backpack load during downhill walking. Conclusion : Since downhill walking while carrying heavy external loads in a backpack may lead to excessive knee joint moment, damage can occur to the joint structures such as joint capsule and ligaments. Therefore, excessive repetitions of downhill walking should be avoided if the lower extremity is subjected to abnormally high levels of load over an extended period of time.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.540-544
• /
• 2008

Pyrolytic characteristics of mixed plastics containing 22 wt.% HDPE, 17 wt.% LDPE, 27 wt.% PP, 12 wt.% PS, 16 wt.% ABS, 6 wt.% PVC have been studied in the batch-type microreactor of stainless steel. Thermal degradation experiments were performed at temperature of $410{\sim}450^{\circ}C$. The yield of each pyrolytic products were obtained by the weight measurement and molecular weight distribution of pyrolytic liquid products determined by the GC-SIMDIS method. It was shown that the yield and molecular weight of pyrolytic liquid product were decreased with the increase of reaction temperature and time. It was know that 20wt% of PVC composing of the mixed plastics was converted to the gas products of chloride during the pyrolysis process. The chain-end scission rate parameter was determined to be 50.2 kcal/mole of mixed plastics by the Arrhenius plot.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.432-437
• /
• 1999

Pyrolysis of polyethylene was carried out in the stainless steel reactor of internal volume of $10cm^3$. Pyrolysis reactions were performed at temperature $390{\sim}450^{\circ}C$ and the pyrolysis products were collected separately as reaction products and gas products. The molecular weight distributions(MWDs) of each product were determined by HPLC-GPC and GC analysis. Distribution balance equation for MWDs of random and specific products were proposed to account for initiation-termination and propagation-depropagation, such as hydrogen abstraction, chain cleavage, coupling of polymer and radical. A separate chain-end scission process produces low molecular weight noncondensable gases(C1 through C5) of average molecular weight 38. Activation energies of the random-chain scission and chain-end scission rate parameters, respectively, were determined to be 35, 17 kcal/mole.

• Microbiology and Biotechnology Letters
• /
• v.8 no.1
• /
• pp.41-46
• /
• 1980

Low molecular weight endo-glucanase was partially purified from cellulase complex using Sephadex G-100 gel chromatography. Biochemical properties of the purified component was investigated. Optimum pH and temperature determined were 6.0 and 5$0^{\circ}C$, respectively. Enzymatic hydrolysis of four cellulosic substrates having varying crystallinity was evaluated. It was found that hydrolysis of amorphous region was followed by the hydrolysis of crystalline region. In order to examine the effect of adsorption of the enzyme onto the cellulosic substrates on the hydrolysis kinetics, adsorption studies were carried out. Time course of adsorption of low molecular weight endo-glucanase onto various cellulostances was observed for 25 min. The rate and amount of adsorption to amorphous cellulose was greater than those to the crystalline cellulose. This result suggested that the role of endo-glucanasc was more important to the hydrolysis of amorphous cellulose than to the crystalline region of the cellulose.

• Journal of Surface Science and Engineering
• /
• v.35 no.6
• /
• pp.363-370
• /
• 2002

Empirical equations for the oxide thickness and the weight gain of Zircaloy-4 cladding during the oxidation in high temperature, high pressure steam have been developed. Firstly, the empirical equations for oxide thickness in 1 atm steam in 700~100$0^{\circ}C$ were made, then, the enhancement factor for the steam pressure effects on Zircaloy-4 cladding oxidation in high temperature steam was added. Based on the analysis of the weight fraction of dissolved oxygen in metal layer, empirical equations for the weight gain of Zircaloy-4 in high pressure, high temperature steam were developed. We compare the developed empirical equations with the Baker-Just correlation. The Baker-Just correlation can give a non-conservative estimation of oxidation of Zircaloy-4, depending on the steam pressure. These developed empirical equations can be used for the correct estimation of oxidation of Zircaloy-4 during accident analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.997-1003
• /
• 2011

In order to investigate devolatilization characteristics for ashless coal with relatively low ash content and high heating value, an experiment was performed in different bed configurations of TGA and DTF(Drop Tube Furnace) at atmospheric pressure condition. The heating rate was $10^{\circ}C$/min up to $950^{\circ}C$ in TGA, while the temperatures of DTF varied from 500 to $1300^{\circ}C$ in step of $200^{\circ}C$. A weight loss and particle temperature were obtained to determine devolatilization kinetics. The kinetic parameters including an activation energy and pre-exponential factor for ashless coal were obtained using Coats-Redfern method in TGA and single step method in DTF. Furthermore, the devolatilization kinetics of the ashless coal were compared with the results of different kinds of conventional coal such as sub-bituminous and bituminous. The results show that the activation energy of devolatilazation for ashless coal is lower than those of others in fixed and entrained conditions.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.3
• /
• pp.115-121
• /
• 2021

Human's landing strategies have been explained through lower extremity kinetics in various conditions. However, how lower extremity kinetics respond when the two conditions between a load and landing height are combined is not yet understood. To achieve the purpose of this study, a total of 20 men and women were subjected to drop landing according to a load(No load, 10%, 20%, 30% of the body weight) at various landing heights(0.3 m, 0.4 m, 0.5 m). As a result of the study, the main effect of a load was not statistically significant in all variables. But increasing of the landing heights showed more flexion angle which was statistically significant in knee joint. In addition, as the landing height increased, the medial-lateral, anterior-posterior, vertical force, and loading rate increased, while time to peak vertical force decreased which was statistically significant. Thus, humans can successfully perform the landing motion even if the load is changed at various heights. However, it reacted more sensitively to the change in landing height than that load condition. The landing height can be prepared for recognition and shock absorption through visual information, but the weight level is difficult for the body to perceive and explains why it is more difficult to apply it to the landing strategy mechanism for shock absorption.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.2
• /
• pp.153-159
• /
• 2011

The purpose of this study was to develop an innovative training model and method to improve the posture and motion, while pulling up during weight lifting by evaluating the problems of Korean weight lifters performing this motion. To investigate the effectiveness of the new training method substitute members of the Korean national weight lifting team performed both the original pull up technique and new pulling training technique while kinetics and kinematics were recorded. For this study, the first phase of the new training method is more appropriate than the original training with the pull up drop slow deadlift to the knee joint. For the second phase, the new training motion is deemed to be more effective than the current box deadlift motion. Also, this new motion corrects the posture as there is more anterior hip joint motion(about 10 cm) and the knee flexes to about 120 degrees. For the third phase, starting about 10cm above the knee the box snatch high pull up is identified as a more suitable training method. For the forth phase, the box top snatch method is judged to be a more effective training method than the original top snatch training method.

• Korean Chemical Engineering Research
• /
• v.51 no.1
• /
• pp.121-126
• /
• 2013

The objective of this research is to predict the TG curve of blends of bituminous coal and sub-bituminous coal during devolatilization. TSL (Thermal Shock Large) TGA was used for Experiments, and Coats-redfern method was used for reaction order calculation. Based on reaction order, sum method was verified to be suitable for a single coal, then, prediction and comparison of TG curve of coal blends was conducted using both of WSM (Weight Sum Method) and MWSM (Modified Weight Sum Method), where the latter was developed in this research. The presented experiment results and WSM & MWSM were showed to be reasonable using linear least square method. MWSM performed more accurately than WSM for the case that TG curve had different slopes and the case that sharp weight loss happened due to release of volatile matter. The results showed that it's possible to predict the thermal behavior of coal blends during devolatilization based on the thermal behavior of single coals.

• BMB Reports
• /
• v.28 no.3
• /
• pp.232-237
• /
• 1995

Arginase was purified to homogeneity from Schizosaccharomyces pombe. The purified enzyme is a tetramer with a subunit molecular weight of 42,000. Activity is optimal at pH 10.0 and at $60^{\circ}C$ The enzyme migrated during isoelectric focusing showing a pl=5.4. The enzyme exhibited hyperbolic kinetics at pH 10.0 with an apparent $K_m$ for L-arginine of 18 mM. Arginase activity was strongly inhibited by L-glutamate.