• Composites Research
• /
• v.23 no.5
• /
• pp.22-29
• /
• 2010

This paper describes the evaluations of tension-compression fatigue characteristics and life for glass fiber/epoxy laminate composite applied to railway bogie to reduce weight. Test samples of tension-compression fatigue were composed of glass fiber/epoxy 4-harness woven laminate composites with different stacking sequence of warp-direction, fill-direction and ${\pm}45^{\circ}$-direction. The tension-compression fatigue test was conducted with stress ratio (R) of -1 and frequency of 5Hz. Goodman diagram were used to evaluate the fatigue characteristics and life of glass fiber/epoxy 4-harness satin woven laminate composite. Anti-buckling jig was designed to prevent buckling of specimen under compression load. The test results showed that the fatigue characteristics of glass fiber/epoxy 4-harness satin woven laminate composite with stacking sequence of warp-direction had a good performance in comparison with that of SM490 used to conventional metal railway bogie.

• Textile Coloration and Finishing
• /
• v.33 no.2
• /
• pp.87-95
• /
• 2021

In this study, the application of a medical compression sleeve of Moisture Responded Transformable(MRT) fibers to the treatment of lymphedema after surgery in breast cancer patients was investigated. MRT fibers were manufactured with PET and Nylon6 bi-component cross-section yarns, and compression sleeves of sleeves 1, 2, 3, and 4 were knitted in order of size, and then the physical properties and clinical tests were evaluated. As a result, the pressure of compression sleeve in wrinkle was the lowest in sleeve 1 with 3.81 kPa, and the highest in sleeve 4 with 5.22 kPa. Elastic recovery rate is that all parts except the top of the sleeve 1 exhibited 100%. The air permeability was good at 12.1 ~ 16.1 cm³/cm²/sec, and peeling was also comparatively excellent as grade 3. In addition, the weight of the compression sleeves 1, 2, and 3 decreased as 18.3 ~ 23.0 g/m² depend on size, while the compared sample was heavier with 17.39 ~ 32.61 g/m². In lymphoscintigraphy test, it was confirmed that the function of remaining lymph node was good in all patients. Although there were no differences between samples in skin irritation and tightness in wearing comfort, the manufactured sleeves showed better fit, lightness, fashion and breathability than the comparable sleeves.

• Journal of the Korean Home Economics Association
• /
• v.36 no.8
• /
• pp.51-61
• /
• 1998

This paper discussed the assessment of hand of polyester fabrics changed by alkaline hydrolysis. This study analyzed the relations between the change of mechanical property and the hand value according to the weight loss of polyester fabrics. The results are as follows; Objective hand by KES-FB system, revealed that for tensile properties, as the weight loss increased, WT, RT increased and LT decreased. For bending properties, as the weight loss increased, B and 2HB showed smaller values. For shear properties, as the weight loss increased, G, 2HG and 2HG5 decreased. For surface properties, as the weight loss increased, MIU increased, but MMD and SMD did not show any trend. For compression properties, LC, WC and RC did not show significant differences according to the degree of weight loss. In case of hand value, Koshi(stiffness), Hari(anti-drape stiffness), Kisimi(scrooping feeling) and Shinayakasa(flexibility with soft feeling) showed a meaningful results depending on the degree of weight loss. However, Shari(crispness) and Fukurami(fullness and softness) did not show meaningful result. Koshi, Hari and Shinayakasa are high correlation with tensile property, bendibg property shear properties, thickness and weight. Kisimi is high correlation with tensile property, bending property, thickness and weight. Shari, Fukurami and THV did not show any meaningful difference whth any mechanical properties.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.23-26
• /
• 2006

The study about the concrete to use recently a light weight aggregate, processed actively. And concrete pumping with a high pressure pump has been popularized, the mechanical development, such as high pressure pumps or pipes, is progressing rapidly. Concrete placing by pumping has the advantage of the reduction of the construction period with workability, easiness of work and the increase of placing, but the quality variation of concrete is caused by pumping is seldom considered, including the increase of the pipe length by high-rising and large-sizing, there by the loss of the unit quantity of water, with pumpability or workability deteriorated. In this research, we will compare and analyze before pumping and after pumping samples of ready-mixed light weight concrete. The result of study as follow. The case of a light weight concrete which the low slump is more decrement compared with high slump light weight concrete in after pumping samples. After pumping the water by pressure of a pump was absorbed to the aggregate inside, and it showed an increase of compression strength about $5{\sim}20%$.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.853-860
• /
• 2003

Relationship between axial strain and volumetric strain of Light-Weighted Foam Soil (LWFS) are investigated. LWFS is composed of the dredged soil from offshore, cement and foam to reduce the unit weight and also increase compressive strength. For this purpose. the triaxial compression tests are carried out on the prepared specimens of LWFS with various conditions such as initial water contents, cement contents, and curing stresses, The test results of LWFS Indicated that the axial strain - volumetric strain relationship is almost linearity with increase cement contents and the unit weight but the relationship is non-linearity with decrease cement contents and the unit weight. In this study, it is found that assuming no change of cross section area of LWFS, axial strain occurring the poisson's ratio of zero, that the axial strain same to volumetric strain, steeply increases with decrease the unit weight, initial water content, and cement contents.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.686-692
• /
• 1999

For the purpose of increasing compressed air pressure higher than 30bar lightening weight and decreasing installation area of air compressor used for shipboard and industrial power plant it is necessary to arrange its cylinders as a w-type or v-type construction multi-stage compression pro-cess more than two stages and to increase its operation speed higher than 1200rpm In this recip-rocating type air compressor operated in high speed having a crank mechanism and complicate cylinder arrangement there is a vibration problems which can be solved by balancing its recipro-cating parts with balance weight and approriate arranging of cylinder's arrangement angles.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.131-135
• /
• 2013

In this study, to develop a light weight duo type aluminum LPG tank in stead of a conventional steel tank optimization technology is used. Two types of optimization method are carried out for internal compression test simulation of a LPG tank. The first is the thickness only optimization of LPG tank components. The second is the thickness and shape optimization. For the case of the thickness only optimization the weight reduction rate of an optimized tank compare to that of the initial design is 42%. Also 48% weight reduction was achieved for the case of the thickness and shape optimization.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.215-224
• /
• 2003

Weathering in nature was simulated by freeze-thaw cyclic test which represents mechanical weathering. Measured physical properties were elastic wave velocities, absorption rate, volume change and weight change. Uniaxial compression tests were also conducted before and after the weathering tests. The change in weight and volume of the specimens were not clearly related to the weathering process, but P, S wave velocities, uniaxial compression strength and Young's modulus were clearly decreased as weathering progresses. Test result can be used for the assessment of long-term stability of rock slopes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.93-98
• /
• 2005

The purpose of this study was to analyze the compression strength research by aerated concrete as mixing ratio This Study used foaming-agent and produced aerated concrete by pre-foam way that is used in construction site. An experiment changes unit cement amount, w/c and the glass fiber mixing rate and 'measured capacity change, unit capacity weight and compressive strength. The results obtained from experimental study are as following; Research to reduce unit capacity weight in condition more than unit cement amount 500kgf is considered should be gone side by side. The highest compressive strength result appeared in aerated concrete that cement amount 600kgf and w/c ratio $45\%$, $50\%$. compressive strength was increased maximum $34%$ when glass fiber $0.7\%$ addition cause by coherence enlargement to enlargement of cement paste and glass fiber addition per unit volume

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.55-64
• /
• 2014

This work was investigated on pilot injection strategy of blended fuels(Diesel-DME) for combustion and emissions in a single cylinder direct injection compression ignition engine. Diesel and DME were blended by the method of weight ratio. Weight ratios for diesel and DME were 95:05 and 90:10 respectively. dSOI between main and pilot injection timing was varied. A total amount of injected fuels(single injection) was adjusted to obtain the fixed BMEP as 4.2 bar in order to compare with the fuel conditions. Also, the amount of pilot injection fuel was varied by 5%, 10% and 20% of total injection fuel. The engine was equipped with common rail and injection pressure is 700 bar at 1200 rpm. As a result, when mixing ratio increase, indicated thermal efficiency was increased in comparison with DD 100 and CO, THC and smoke were lower than DD 100. The influence of reducing NOx by pilot injection was more effective than DD 100. When pilot injection quantity increase, abrupt increase of NOx was occured at pilot injection quantity of 20%.