• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.972-981
• /
• 2000

The phased array transducer has two distinct advantages. One is rapid scanning comparing with the conventional mechanical or manual scanning system. Therefore, output image is represented in real-time. The other is the dynamic focusing and the dynamic steering of ultrasonic beam. Only the delay times that are controlled electrically are used to focus and to steer beam without any lenses or wedges. In this study, the profile of the ultrasonic beam for the phased array transducer has been simulated in the Huygens principle with varying the inter-element spacing of the linear phased array transducer. From the result of this study, it was found that the ultrasonic beam spread wider as the inter-element spacing was decreased. However, the focusing effect was improved, even when the number of the element was not big. In addition, there was grating lobes that are constructed when the inter-element spacing is more than half wavelength. However, this grating lobe has lower amplitude than the main lobe.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.3
• /
• pp.328-335
• /
• 2009

In order to 1ransport the steel roll coil effectively and safely to the destination, the stability of the steel roll coil which induced the minimum movements during the 1ransportation was s1rongly required. The basic 1ransportation equipment for the steel roll coil such as the wedge is made of 100% imported wood known as the apitong. However, the material characteristic such as the rigidity has caused permanent damages to the steel roll coil and the damaged steel roll coils were not easily restorable. Thus it was unsuitable for other purposes. The introduction of new materials to manufacturing wedges which would have a good recovery performance and thus enable the wedge prevention or reduction to the steel roll coil or any other products during the 1ransportation is needed. Due to the fact that recovering damage of the coil is almost impossible, we have to find the new type of wedge that can substitute the apitong wedge. Therefore, we are going to develop a wedge that does not damage rolled steel coil and has better recovery and softness than existing apitong wedge.

• Journal of radiological science and technology
• /
• v.22 no.1
• /
• pp.61-66
• /
• 1999

The use of multileaf collimator(MLC) to replace conventional field-shaping techniques is not in itself expected to improve the local control of malignancy. The purpose for using MLCs in conventional radiation oncology is to improve the efficiency of treatment delivery. For effective clinical application of MLCs to shaped radiation field, field outline must be translated into MLC leaf position tables. The intended leaf positions contained in these tables must then be communicated to the control computer that drives the MLC. There are currently at least three techniques utilized by manufacturers of MLCs and treatment planning systems for doing this. The Varian series use a workstation employing a manual digitizer and light box especially. It has a third level MLC configuration and also has the option of placing the wedges above or below the block tray. The C language are used for development of software and three leaf coverage have been used for positioning MLC loaves at the nominal field boundary. The fit of the leaf shape to treatment target volumes are optimized by the rotation of the direction in leaf travel. The clinical application of this software are investigated for Varian MLCs used in linear accelerator of Yonsei Cancer Center. The advantage of the results with using this software is to prescribe and calculate exposed and blocked area in MLCs field.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.655-661
• /
• 2007

A new steel connection method using wedges known as Self-Locking Connector has been developed. In this study, experimental investigation was conducted to verify the seismic performance of steel beam-to-column joints with Self-Locking Connectors. Cyclic-loading tests were performed on two beam-to-column joints with Self-Locking Connectors. The two beam-to-column joint specimens were of the cantilever-type and had the same details. Test results showed that beam-to-column joints with Self-Locking Connectors were able to developa total rotation capacity of 0.06 radian, which is greater than the 0.04 radian required for Special Moment Frames. Moreover, their energy absorption capacity was much greater than that of conventional joints.

• Journal of Mechanical Science and Technology
• /
• v.14 no.6
• /
• pp.690-698
• /
• 2000

The laminar boundary layer flow and heat transfer of anisotropic fluids in the vicinity of a wedge have been examined with constant surface temperature. The similarity variables found by Falkner and Skan are employed to reduce the stream wise-dependence in the coupled nonlinear boundary layer equations. The numerical solutions are presented using the fourth-order Runge - Kutta method and the distribution of velocity, micro-rotation, shear and couple stresses and temperature across the boundary layer are plotted. These results are also compared with the corresponding flow problems for Newtonian fluid over wedges. It is found that for a constant wedge angle, the skin friction coefficient is lower for micropolar fluid, as compared to Newtonian fluid. For the case of the constant material parameter K, however, the magnitude of velocity for anisotropic fluid is greater than that of Newtonian fluid. The numerical results also show that for a constant wedge angle with a given Prandtl number, Pr = I, the effect of increasing values of K results in increasing thermal boundary layer thickness for anisotropic fluid, as compared with Newtonian fluid. For the case of the constant material parameter K, however, the heat transfer rate for anisotropic fluid is lower than that of Newtonian fluid.

• Geomechanics and Engineering
• /
• v.20 no.4
• /
• pp.287-297
• /
• 2020

This paper investigates the stability of a three-dimensional (3D) wedge under the pseudo-static action of an earthquake based on the nonlinear Barton-Bandis (B-B) failure criterion. The influences of the mechanical parameters of the discontinuity surface, the geometric parameters of the wedge and the pseudo-static parameters of the earthquake on the stability of the wedge are analyzed, as well as the sensitivity of these parameters. Moreover, a stereographic projection is used to evaluate the influence of pseudo-static direction on instability mode. The parametric analyses show that the stability coefficient and the instability mode of the wedge depend on the mechanical parameter of the rock mass, the geometric form of the wedge and the pseudo-static state of the earthquake. The friction angle of the rock φ_b, the roughness coefficient of the structure surface JRC and the two angles related to strikes of the joints θ₁ and θ₂ are sensitive to stability. Furthermore, the sensitivity of wedge height h, the compressive strength of the rock at the fracture surface JCS and the slope angle α to the stability are insignificant.

• Journal of Korean Physical Therapy Science
• /
• v.19 no.2
• /
• pp.1-7
• /
• 2012

Purpose : The purpose of this study was to investigate the effect of different heel height on the electromyographic (EMG) activity in Rectus abdominis (RA) and Erector spinae (ES) during gait activity. Methods : A repeated measures design was used. 33 healthy females carried out a standardized gait activity under 3 conditions; with heel wedges of 1, 7, and 12cm in height. EMG activity was recorded from RA and ES during the activity. Data was analysed using the repeated one-way ANOVA. Results : First, as the shoe-heel height was getting higher, change of muscle activation indicated the statistically significant difference in rectus abdominis(p<0.05). Second, as the shoe-heel height was getting higher, change of muscle activation indicated the statistically significant difference in erector spinae(p<0.05). Conclusion : We found that as heel height increased, there was an increase in EMG activity in both RA and ES. This indicated that no RA : ES imbalance was elicited. This study provides information that will inform future research on how heel height affects muscle activity around the trunk.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.46 no.1
• /
• pp.59-69
• /
• 2013

Temporal and spatial variation in the freshwater region, created by river runoff, of a small bay, caused by the passage of typhoons was examined using a three-dimensional primitive equation model (the Princeton Ocean Model, POM). Numerical experiments were implemented focusing on temporal evolution in the freshwater region in association with typhoon tracks. The model domain covered most of the estuary around the Nakdong River, including Noksan Bay, where river water is periodically released from upstream (Noksan dam). The model showed that the extension of the freshwater region outside of the bay depended strongly on the tracks of typhoons, specifically the associated wind directions and inner flow fields that are accompanied by new clockwise eddies. The model also showed that entrainment from typhoon passage frequently creates salt wedges in the estuary, indicating that organisms in the bay are biologically and chemically influenced with variation in the freshwater region.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.86-94
• /
• 1999

Measured shock wave effects were investigated by changing shock strength and position with particular emphasis on the stability limits of hydrogen-air jet flames. For this purpose, a supersonic nonpremixed, jet-like flame was stabilized along the axis of a Mach 2.5 wind tunnel, and wedges were mounted on the sidewall in order to interact oblique shock waves with the flame. This experiment was the first reacting flow experiment interacting with shock waves. Schilieren visualization pictures, wall static pressures, and flame stability limits were measured and compared to corresponding flames without shock-flame interaction. Substantial improvements in the flame stability limits were achieved by properly interacting the shock waves with the flameholding recirculation zone. The reason for the significant improvement in flame stability limits is believed to be the adverse pressure gradient caused by the shock, which can elongate the recirculation zone.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.65-71
• /
• 1999

An experimental study was carried out in order to investigate the effect of shock waves on the supersonic hydrogen-air jet flames stabilized in the Mach 2.5 model scramjet combustor. This experiment was the first reacting flow experiment interacting with shock waves. Two identical $10^{\cire}$ wedges were mounted on the diverging sidewalls of the combustor in order to produce oblique shock waves that interacted with the flame. Schlieren visualization pictures, wall static pressures, and combustion efficiency at two different air stagnation temperatures were measured and compared to corresponding flames without shock wave-flame interaction. It was observed that shock waves significantly altered the shape of supersonic jet flames, but had different effects on combustion efficiency depending on air temperatures. At the higher air stagnation temperature and higher fuel flow rates, combustion of efficiency showed a better result.