• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.5-14
• /
• 1995

In recent years, the automization of cutting machine tools has been developed very fast. Hance, the in-process detection of cutting condition is very important for automatic manufacturing system in factory. Acoustic Emission(AE) has been widely used in monitoring the cutting conditions, because of high sensitivity of AE signal and low cost of AE equipment. This experimental study deals with the relations between AE signal, cutting force charcteristics and tool wear in the machining of SUS304. Face milling operation is used for the analysis between tool wear and AE signal.

• 한국정밀공학회지
• /
• 제14권2호
• /
• pp.58-65
• /
• 1997

Work rolls used in cold rolling mills must have outstanding wear resistance and very little plastic defor- mation. Thus, these rolls require a higher surface hardness and harding to a greater depth. To meet these requirements, the rolls, in general, have basic chemical composition of 0.7 to 1.0% carbon and 1.0 to 5.0% Cr(chromium), plus a small amounts of special elements, and are subjected to intensive water quenching and tempering at low temperature to provide a surface hardness of over 90 shore. This test results are as follows. Deflection and fracture load of 5% Cr material are than those of 3% Cr material and show flat curve from surface to subsurface. It will be clear that 5% Cr work roll has a superior resisti- bility against wear and abrasion comparing with 3% Cr work roll. The improvement of wear and abrasion in 5% Cr work roll will be achieved by the large amount of wpheroidal carbide. In grindability and polish, 5% Cr work roll will be a little inferior comparing with 3% Cr work roll.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.873-877
• /
• 1997

This paper presents experimental results to know the charcteristics of machined surface due to cutter runout. Cutter runout is a common but undesirable phenomenon in multi-tooth machining such as end-milling process because it introduces variable chip loading to insert which results in a accelerated tool wear, amplification of force variation and hence enargement vibration amplitude. To develop in-proess cutter runout compensation system, set-up the micro-positoning mechanism which is based on piezoelectric translator embeded in the work holder to manipulate the depth of cut in real-time. And feasibility test of system was done under the various experimental cutting conditions. This results provide lots of information to build-up the precision machining technology.

• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.721-725
• /
• 1998

본 연구에서는 Boron과 Carbon black이 소결조재로 첨가된 탄화규소 분말을 $1950^{\circ}C$에서 상압소결 방법으로 시편을 제조하고 꺽임강도, 파괴인성, 비마모량을 측정하고 파단면 및 마찰마모면의 미세구조를 SEM으로 관찰하여 마찰마모특성과 미세구조와의 관계를 규명하였다. 또한 마모상대재료로서 SiC pin과 $Al_{2}O_{3}$ pin을 사용하였을때 마찰마모특성과 미세구조와의 관계도 비교 검토하였으며 다음과 같은 결론을 얻었다. 1. SiC pin을 사용한 경우 소결시편의 비마모량은 $Al_{2}O_{3}$ pin을 사용한 경우보다 많았으나, 가압하중이 증가하면 $Al_{2}O_{3}$ pin을 사용한 경우가 SiC pin을 사용한 경우보다 비마모량의 증가율이 6.5배로 되었다. 2. Pin의 비마모량은 SiC pin의 경우가 $Al_{2}O_{3}$의 경우보다 많았으나 가압하중이 증가하면 $Al_{2}O_{3}$ pin의 경우가 SiC pin의 경우보다 비마모향의 증가율이 약4배로 되었다. 3. 마모상대재료의 마찰계수가 작은 경우에는 마모면의 미세구조가 평활하면서 crack이 나타나지 않았으나, 마찰계수가 큰 경우에는 마모면이 평활치 못하고 crack의 전파현상이 크게 나타났다. 4. 사용된 Pin의 마찰계수가 큰 경우에는 고상소결한 SiC 시편도 액상소결한 시편과 마찰마모 특성이 유사하였다.