• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1087-1093
• /
• 2012

In this paper, we implemented a HF-band magnetic-field communication system consisting of an amplitude shift keying(ASK) transmitter, a pair of loop antennas, and an ASK receiver. Especially, we suggested a new ASK transmitter architecture, where a drain bias of class E amplifier is switched alternatively between two voltage levels with respect to input data. A maximum 5 W class E amplifier was designed using a low cost IRF510 power MOSFET at the frequency of 6.78 MHz. A measured sensitivity of the designed ASK receiver is -78 dBm, which consists of a log amplifier, a filter, and a comparator. Maximum communication range of magnetic-wave communication system with loop antennas was calculated using magnetic field equations in both near-field and far-field ranges. Also, in order to verify the calculated values, an indoor propagation loss was measured using a pair of loop antennas whose dimensions are $30{\times}30cm$. Maximum operating range is estimated about 35 m in case of transmitter's output power of 1 W and receiver sensitivity of -70 dBm, respectively. Finally, the communication field test using the designed ASK transmitter and receiver was successfully done at the distance of 5 m.

• Journal of Navigation and Port Research
• /
• v.34 no.3
• /
• pp.175-180
• /
• 2010

In the almost application parts, GNSS being used the primary navigation system on world-widely. However, some of nations attempt or deliberate to enhance current Loran system, as a backup to satellite navigation system because of the vulnerability to the disturbance signal. Loran interests in supplemental navigation system by the development and enhancement, which is called eLoran, and that consists of advancement of receiver and transmitter and of differential Loran in order to increase the accuracy of current Loran-C. A significant factor limiting the ranging accuracy of the eLoran signal is the ASF in the TOAs observed by the receiver. The ASF is mostly due to the fact that the ground-wave signal is likely to propagate over paths of varying conductivity and topography. This paper presents comparison results between the predicted ASF and the measured ASF in a southern east region of Korea. For predicting ASF, the Monteath model is used. Actual ASF is measured from the legacy Loran signal transmitted Pohang station in the GRI 9930 chain. The test results showed the repeatability of the measured ASF and the consistent characteristics between the predicted and the measured ASF values.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.2
• /
• pp.102-110
• /
• 2014

The effect of a bonding layer on the performance of a quarter-wave (${\lambda}/4$) mode PVDF ultrasound transducer having not only a piezoelectric layer but also a non-piezoelectric layer between two electrodes was analyzed. The equivalent circuit of a transmission line model by Kikuchi et al.[Sound of IEICE, 55-A, 331-338 (1981)] was introduced for the analysis. The validity of the model was confirmed by comparison with a KLM model for three postulated adhesion cases of a $80{\mu}m$ thick piezoelectric PVDF film to a copper (Cu) backer. The pulse-echo responses of five PVDF transducers, each fabricated with a different thickness ($5{\mu}m{\sim}20{\mu}m$) of the bonding layer, were measured and the results were compared with those by simulation. The two results were in good agreement with each other and it was noted that the effect of the bonding layer on the performance of the transducer could be analyzed by the Kikuchi model. In detail, the $20{\mu}m$ bonding layer decreased the center frequency and the bandwidth by about 19.7 % and 25.0 %, respectively, and increased the insertion loss by 57.2 %.

• 한국지구물리탐사학회:학술대회논문집
• /
• 1999.08a
• /
• pp.92-116
• /
• 1999

Tomographic approaches to image underground structure using electrical properties, can be divided into DC resistivity, electromagnetic, and radar tomography, based on the operating frequency. DC resistivity and radar tomography methods have been recently applied to site investigation for engineering purpose in Korea. This paper review these two tomography methods, through the case histories acquired in Korea. As another method of borehole radar survey, borehole radar reflection method is included, and its inherent problem and solution are discussed, how to find the azimuth angle of reflector using direction-finding-antenna. Since the velocity anisotropy of radar wave has been commonly encountered in field data, anisotropic radar tomography is discussed in this paper. In DC resistivity tomography, two subjects are focussed, electrode arrays, and borehole effect owing to the conductive fluid in borehole. Using the numerical modeling data, various kinds of electrode ways are compared, and borehole effect is illustrated. Most of the case histories presented in this paper are compared with known geology, core logging data, and/or Televiewer images.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.4
• /
• pp.431-439
• /
• 2010

Cross-interferometic synthetic aperture radar (CInSAR) technique from ERS-2 and Envisat images is capable of generating submeter-accuracy digital elevation model (DEM). However, it is very difficult to produce high-quality CInSAR-derived DEM due to the difference in the azimuth and range pixel size between ERS-2 and Envisat images as well as the small height ambiguity of CInSAR interferogram. In this study, we have proposed an efficient method to overcome the problems, produced a high-quality DEM over northern Alaska, and compared the CInSAR-derived DEM with the national elevation dataset (NED) DEM from U.S. Geological Survey. In the proposed method, azimuth common band filtering is applied in the radar raw data processing to mitigate the mis-registation due to the difference in the azimuth and range pixel size, and differential SAR interferogram (DInSAR) is used for reducing the unwrapping error occurred by the high fringe rate of CInSAR interferogram. Using the CInSAR DEM, we have identified and corrected man-made artifacts in the NED DEM. The wave number analysis further confirms that the CInSAR DEM has valid Signal in the high frequency of more than 0.08 radians/m (about 40m) while the NED DEM does not. Our results indicate that the CInSAR DEM is superior to the NED DEM in terms of both height precision and ground resolution.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.4
• /
• pp.637-637
• /
• 1997

In this paper, format conversion filters are proposed, which have advantages in hardware implementation compared to the ones proposed in MPEG-4 Video Verification Model. since each coefficients of the proposed filters is constrained to have less than two non-zero digits in minimal signed digit representation, multiplication of input and the coefficient can be implemented by a single adder. As a result, the proposed filters have advantages in hardware complexity and speed, compared to the filters which are usually implemented by integer multiplier or carry save adders. Six kinds of filters are proposed in MPEG-4 Video Verification Model for size conversion of 2:1, 4:1, 5:3 and 5:6. We design 5 filters for the same purpose and compare the performance. The remaining one is very simple to implement. For comparing the filtering performance, we first compare the results of sine wave frequency conversion as an indirect but meaningful comparison. Second. We compute the PSNR of the images obtained from the proposed filters and the ones proposed by MPEG, with reference to the images obtained by using double precision arithmetic and high order filter. The results show that the performance of the proposed filters is almost the same as that of the filters proposed by MPEG. In conclusion, the peroformance of the proposed filters is comparable to that of the ones in MPEG-4, while requiring lower hardware complexity and providing high operating speed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.754-763
• /
• 2002

This paper discusses the improved power performances of the size-reduced amplifier using defected ground structure (DGS). The slow-wave effect and enlarged electrical length occur due to the additional equivalent circuit elements of DGS. Using these properties, it is possible to reduce the length of transmission lines in order to keep the same original electrical lengths by inserting DGS on the ground plane. The matching and performances of the amplifier are preserved even after DGS patterns have been inserted. While there is no loss in the size-reduced transmission lines at the operating frequency, but there exists loss to some extent at harmonic frequencies. This leads to the more excellent inherent capability of harmonic rejection of the size-reduced amplifier. Therefore, it is expected tile harmonics of the size-reduced amplifier are smaller than those of the original amplifier. The measured second harmonic, third order intermodulation distortion (IMD3), and adjacent channel power ratio (ACPR) of the size-reduced amplifier are smaller than those of the original amplifier by 5 dB, 2~6 dB, and 1~4 dB, respectively, as expectation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.9
• /
• pp.2280-2288
• /
• 2014

The conventional dimming control methods of LED (Light-emitting dioades) include Analog, PWM (Pulse Width Modulation), and FM (Frequency Modulation) Control. Analog dimming is controlled by adjusting forward current of Power LED. Although Analog dimming is possible to control linearly the brightness levels on a whole range (0%~100%), it comes into existence a variation of wavelength by changing the Power LED's forward current. PWM dimming has achieved by varying in duty of full current flowing to the Power LED. Generally, PWM dimming doesn't make variation of wavelength but have difficulty with adjusting the linear brightness level between 0% and 10%. FM dimming method is on the same wavelength as PWM dimming, however, it has problem of flickering at low level of dimming. This paper propose a efficient dimming control method of Power LED in order to overcome the disadvantages of the above mentioned methods. We apply to Analog method in low level of dimming control and use PWM method in dimming range from 10% to 100%. For the experiment, we design and implement a circuit and test the proposed method. Consequently, we can control the linear brightness of Power LED across the whole range and get the constant wave at different dimming level. The experimental results show the benefits of the proposed method.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.21-31
• /
• 2014

Recently, the research on renewable energy against depletion of fossil fuel have been actively carried out in the world. Especially, offshore wind turbines are very economical and innovative technology. However, offshore wind turbines experience large base moments due to the wind and wave loading, so the monopile with large diameter needs to be applied. For the economical design of the large diameter pile, it is important to consider the flexibility of the foundation to estimate the maximum moment accurately, based on studies conducted so far. In this paper, the foundation was modeled using the finite element method in order to better describe the large diameter effect of a monopile and the results were compared with those of p-y method. For the examples studied in this paper, the change in maximum moment was insignificant, but the maximum tilt angle from the finite element method was over 14% larger than that of p-y method. Therefore, the finite element approach is recommended to model the flexibility effect of the pile when large tilt angles may cause serviceability issues.

• 한국해양학회지
• /
• v.29 no.2
• /
• pp.152-163
• /
• 1994

The characteristics and fluctuations of structures and spatial distributions of warm eddies (anticyclonic eddies) in the southwestern part of the East Sea (the Japan Sea) are discussed based on the data gathered y the Fisheries Research and Development Agency, Korea from 1967 to 1968. The warm eddies existed very often in the southwest of the Ullung Island. The warm eddies are elliptical in shape and the mean size is about 130 km in diameter. Bimonthly distributions of warm eddies, the largest value of observed frequency and diameter in August and the least in June, indicate that the generation of the warm eddy is related with the development of the East Korean Warm Current. The warm eddies move west, north or southward with 0.80∼2.50 cm/sec or stay over a few months at the same place southwest of the Ullung Island. Movement of warm eddies may be influenced by the neighboring currents, the Rossby wave and the topography. The relationship between the position of warm eddies and the bottom topography suggests that the development and the movement of warm eddies are controlled by the Ullung Basin. The warm eddies should be divided into two groups. One group is the shallow warm eddy with strong baroclinic characteristics and the other is the deep one with strong Barotropic characteristics. The shallow group seems to be closely related with positive values (in summer) of the sea level difference between Pusan and Mozi (the Tsushima Current), while the deep group has no relation with that.