• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.630-634
• /
• 2007

In the past, the use of wave energy has mainly been focused on conversion of large wave energy resources in the far offshore areas. However, with the technological improvement of converting wave energy into electricity, the energy resources at much shallow waters are now considered as a site for possible installation of the devices that obtain energy from the waves. In this respect, the wave energy resources on the east coast of Korea, where the sea is milder than the open ocean, were investigated using the field measurement data obtained at three different locations along the coast. For all the locations, the wave power was greater in winter season, compared to summer season. The estimated wave power varied from 2 to 4.5 kW/m on average, depending on the measurement locations.

• 한국인터넷방송통신학회논문지
• /
• 제22권2호
• /
• pp.43-50
• /
• 2022

본 논문에서는 밀리미터파 W대역에서 동작하는 안테나 성능 측정을 위한 원-전계 측정 시스템을 설계하고 검증하였다. 안테나 성능 시험은 안테나의 종류, 측정 항목, 측정 환경 및 기간 등에 따라 측정 시스템을 선택해야 한다. 근접 전계 측정은 안테나가 다중 채널을 가지거나 다양한 빔을 가지고 있을 경우, 측정 항목이 증가하기 때문에 많은 시간이 소요된다. 이러한 안테나는 원-전계 측정을 통해 측정 시간을 단축 할 수 있고 필요한 측정 항목만 측정이 가능하다. 따라서 본 연구는 원-전계 측정 시스템을 고출력 레이저를 이용하여 정밀한 정렬을 확보하고 이중 증폭기 시스템을 적용하여 측정 정확도를 향상하였다. 설계된 시스템은 무반향 챔버 내 구축하였으며 검증된 근접 전계 측정 시스템과 비교하여 검증하였다.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.382-390
• /
• 2021

The present study suggests the application of a depth camera for wave height field measurement, focusing on the calibration procedure and test setup. Azure Kinect system is used to measure the water surface elevation, with a field of view of 800 mm × 800 mm and repetition rate of 30 Hz. In the optimal optical setup, the spatial resolution of the field of view is 288 × 320 pixels. To detect the water surface by the depth camera, tracer particles that float on the water and reflects infrared is added. The calibration consists of wave height scaling and correction of the barrel distortion. A polynomial regression model of image correction is established using machine learning. The measurement results by the depth camera are compared with capacitance type wave height gauge measurement, to show good agreement.

• 대한기계학회논문집A
• /
• 제29권11호
• /
• pp.1439-1444
• /
• 2005

A two-dimensional boundary element method was used for the scattering analysis of side-drilled hole(SDH). The far-field scattering amplitude was calculated for shear vertical(SV) wave, and their frequency and time-domain results were presented. The time-domain scattering amplitude showed the directly reflected wave from the SDH leading edge as well as the creeping wave. In an immersion, pulse-echo testing, two measurement models were introduced to predict the response from SDHs. The 2-D boundary element scattering amplitude was converted to the 3-D amplitude to be used in the measurement model. The receiver voltage was calculated fer SV wave incidence at 45$^{\circ}C$ on the 1 m diameter SDH, and the result was compared with experiment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 춘계학술대회논문집; 부산수산대학교, 10 May 1996
• /
• pp.275-285
• /
• 1996

A noise measurement method of the multi-sound sources in a reverberation field with wave-guide is developed by experimental method. In the reverberation field, it is very hard to measure sound level or noise spectra of a certain sound source, when many sound sources generate noise simultaneously with a small space between them. Flexible wave-guide(tube) was used to measure noise level in a reverberation field. One end of the tube is attached to a sound source and the other end is closed with an anechoic terminal. Detailed method of the measurement and the source of error was considered as well.

• 대한기계학회논문집B
• /
• 제24권7호
• /
• pp.924-929
• /
• 2000

This paper addresses a new technique of measuring the mean flow velocity over the cross sectional area of the pipe using sound field reconstruction. When fluid flows in the pipe and two plane waves propagate oppositely through the medium, the flow velocity causes the change of wave number of the plane waves. The wave number of the positive going plane wave decreases and that of negative going one increases in comparison to static medium in the pipe. Theoretical backgrounds of this method are introduced in detail and the measurement of mean flow velocity using the sound field reconstruction is not affected by velocity profile upstream of microphones.

• 한국전자파학회논문지
• /
• 제20권1호
• /
• pp.91-99
• /
• 2009

본 논문에서는 micro-TEM cell을 사용한 표준 전자기장 발생법을 기술하고 측정불확도를 평가하였다. 표준 전자기장 발생 시스템은 auto-leveling 기능을 가진 신호발생부, 최대 1.2 GHz까지 동작하는 micro-TEM cell, 서미스터 마운트를 사용한 전력측정부로 구성된다. 표준 전자기장 발생법의 타당성을 보이기 위해 $10\;MHz{\sim}1\;GHz$ 대역에서 전자기장의 세기 20 V/m에 대해 실시된 전자기장의 세기 국제비교(CCEM.RF-K20)의 참여 결과를 제시하였다.

• 소음진동
• /
• 제7권1호
• /
• pp.43-53
• /
• 1997

This paper investigated the practical use for measuring the structural intensity (power flow per width of cross section) in a uniform semi-infinite beam in flexural vibration. The structural intensity is obtained as a vector at a measurement point, One-dimensional structural intensity can be obtained from 4-point cross spectral measurement, or 2-point measurement on the assumption of far field. The measurement errors due to finite difference approximation and phase mismatch of accelerometers are examined. For precise measurements, it would be better to make the value of k$\delta$(wave number x space between accelerometers) between 0.5 and 1.0. Formulation of the relation between bending waves in structures and structural intensity makes it possible to separate the wave components by which one can get a state of the vibration field. Experimental results are obtained from 2- and 4-point measurement performed at 200mm (near field) and 400mm (far field) apart from excitation point in random excitation. the results are compared with the theoretical values and measured values of input power spectrum in order to verify the accuracy of structural intensity method, 2-point method is suggested as the practical structural intensity method.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1650-1658
• /
• 2011

The quality control of compaction fills has been commonly performed via the field density measurement and plate load tests. However, the engineer frequently encounters difficulties in actually controling the quality due to the uncertainty in the field density measurement as well as the plate load tests. To overcome these difficulties, Park et al. (2009) proposed an alternative quality control method based on the measurement of the compressive wave velocities. In this study, the compressive wave velocities measured in the full-scale model test site were analyzed. Direct arrive seismic tests were performed after the completion of each trackbed layer. To identify a relationship between elastic wave velocities and degree of compaction, laboratory compaction tests were conducted.

• 신재생에너지
• /
• 제3권3호
• /
• pp.28-35
• /
• 2007

In this study, the wave power resources at the three locations [Sokcho, Hupo, and Onsan] on the east coast of Korea were estimated by using the field measurement data and were compared with the results of previous researches. It was found that seasonal variation of the wave power is very significant on the east coast of Korean peninsula. The wave power was the smallest in the summer season at all the locations. At Hupo and Onsan, the highest value of the monthly-averaged wave power was observed in September, probably because the pathways of typhoon in September were close to both locations. At the northest location, Sockcho, in contrast, the monthly highest value of the wave power appeared in January, probably owing to the influence of storm waves driven by Donghae twister. The estimated annual average wave power was 4.5 kW/m at Sokcho, which was about two times larger than those at other two locations. It is noteworthy that this result is completely different from past researches based on wave hindcasting data. In addition, the estimates of wave power by the past researches seemed to be smaller than those of the present study, especially at the northern region of the east coast.