• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.821-827
• /
• 2015

This study concentrates on a wave energy converter with floaters that extracts the ocean's energy by moving up and down with the wave motion. The floater is connected to an arm structure, including a hydraulic cylinder that drives a hydraulic generator. This study focuses on a structural analysis of the floater unit, including arm and cylinder components, platform and jack-up system, along with spud columns. Previous studies have been conducted for miniature models for experimentation, but this study focuses on the full-scale model structural analysis. Static structural analysis is conducted using fine numerical grids. Due to the complexity of the whole model, it is analyzed in separate pieces. The floater unit, with arm and cylinder, are combined into one system. The platform is analyzed separately as a single system. There are four jack-up systems for each spud column; only one jack-up system is analyzed, as uniform loads are assumed on each system. There are several load cases for each system, all of which are analyzed thoroughly for stress (von Mises, shear, and normal) and deformation. Acceptable results were obtained for most of the components; unsafe components were redesigned.

• Journal of Drive and Control
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2014

This paper presents a novel concept of wave energy converter for electric generation from the ocean wave energy. In this paper, a Multi-Point Absorbing Wave Energy Converter, shortened as MPAWEC by using Secondary Control Hydrostatic Transmission (SCHST) was proposed. The power take-off (PTO) system in the proposed MPAWEC includes multi heaving buoys to drive hydraulic pumps placed at different points. The application of SCHST in MPAWEC gives some advantages, such as longevity of hydraulic components; more energy is harvested; the variation of the pressure in the accumulator limited; therefore the accumulator volume is reduced and the output speed is more stable, etc. A PID controller was designed for speed control of the hydraulic motor. The simulation results indicated that the speed of the generator was ensured with the relative error as 0.67%; the efficiency of the proposed system was 71.4%.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1133-1136
• /
• 2002

We designed and fabricated a low local oscillation (LO) power V-band CPW mixer module using a CPW-to-waveguide transition technology for the application of millimeter-wave wireless communication systems. The mixer was designed using a unique gate mixing architecture to achieve simultaneously a low LO input power, a high conversion gain, and good LO-RF isolation characteristics. The fabricated mixer exhibited a high conversion gain of 2 dB at a low LO power of 0 dBm. For data transmission of the 60 ㎓ wireless LNA systems, we fabricated a CPW-to-waveguide converter module of WR-15 type and mounted the fabricated mixer in the converter module. The fabricated V-band mixer exhibited a higher conversion gain and a lower LO input power than other reported V-band mixers.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2562-2564
• /
• 1999

We have development the electronic ballast for metal halide discharge (MHD) lamp. The ballast consists of the boost pre-converter for power factor correction (PFC), a flyback a converter, half-bridge inverter and ignitor. To reject acoustic resonance phenomena, we have designed electronic ballast driving with the low frequency square wave. As results of this study, the ballast had not flicker phenomena and promoted corrected the factor (PF) highly

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.158-159
• /
• 2003

In four-wave-mixing wavelength converter, we investigated the performance through simulation by using VPI tool, changing the input signal power and CW power at 2.SGb／s. Controlling optimal CW power to each input signal power, we extended the input signal power range to 20dB, which guarantees the minimum power penalty.

• Journal of Navigation and Port Research
• /
• v.33 no.7
• /
• pp.501-504
• /
• 2009

There are many difficulties to supply constant power to marine facilities which operate in the sea. Especially, there is a limit to stand alone power supply systems due to the influence of weather conditions. That's why a hybrid power supply system is required to overcome these problems. This paper will describe an Electronic Anti-Fouling System (EAFS) to maximise the power efficiency for a solar - wave hybrid power generation system. A main factor reducing the efficiency of a Wave Energy Converter (WEC) is due to the attachment of aquatic life forms. Therefore the aim of this research is to develop a simulation programme to enable the design of more efficient EAFS for hybrid power generation systems and to provide valuable data for production of more efficient EAFS.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1311-1317
• /
• 2008

In this paper, a fault location algorithm using wavelet transform is proposed for HVDC cable lines. The arriving instants of the first and second fault-induced backward travelling waves can be detected by using wavelet transform. The fault distance is estimated by using the time difference between the two instants of backward travelling waves and the velocity of the travelling wave. To distinguish between the backward wave from fault point and the backward wave from the remote end, polarities of backward waves are used. The proposed algorithm is verified varying with fault distances and fault resistances in underground cables of VSC(voltage source converter) HVDC system and CSC(Current Source Converter) HVDC respectively. Performance evaluations of the proposed algorithm shows that it has good ability for a fault location of HVDC cable faults.

• Ocean Systems Engineering
• /
• v.13 no.3
• /
• pp.225-245
• /
• 2023

In the present paper, a numerical and experimental analysis for a wave energy converter under extreme environmental conditions is carried out. After the definition of design waves, including a 100-year return period stochastic sea state and a deterministic rogue wave condition, a numerical analysis using potential theory and a RANS equations solver are compared with experiments carried out at the Seakeeping Basin at the Technical University of Berlin. Results are discussed with special emphasis on the limits of potential theory methods for the evaluation of extreme wave conditions and the use of the presented methodology for early design stages.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.4
• /
• pp.513-528
• /
• 2013

A floating Oscillating Water Column (OWC) wave energy converter, a Backward Bent Duct Buoy (BBDB), was simulated using a state-of-the-art, two-dimensional, fully-nonlinear Numerical Wave Tank (NWT) technique. The hydrodynamic performance of the floating OWC device was evaluated in the time domain. The acceleration potential method, with a full-updated kernel matrix calculation associated with a mode decomposition scheme, was implemented to obtain accurate estimates of the hydrodynamic force and displacement of a freely floating BBDB. The developed NWT was based on the potential theory and the boundary element method with constant panels on the boundaries. The mixed Eulerian-Lagrangian (MEL) approach was employed to capture the nonlinear free surfaces inside the chamber that interacted with a pneumatic pressure, induced by the time-varying airflow velocity at the air duct. A special viscous damping was applied to the chamber free surface to represent the viscous energy loss due to the BBDB's shape and motions. The viscous damping coefficient was properly selected using a comparison of the experimental data. The calculated surface elevation, inside and outside the chamber, with a tuned viscous damping correlated reasonably well with the experimental data for various incident wave conditions. The conservation of the total wave energy in the computational domain was confirmed over the entire range of wave frequencies.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.3
• /
• pp.26-32
• /
• 2015

The authors are developing a motion of floater body type wave energy converter of the float-counterweight system. This consists of the driving pulley, wire, float and counterweight suspended from idler pulleys and rachet mechanism. Though it has succeeded in solving the major structural strength problem in which the floats would slam against adjacent structure(s) by wave load acting horizontally. In order to overcome this problem. We propose a new system in which the wire transmitting the power is wound around the pulleys and the float receiving the wave power is pulled by the wire from both its upper and lower ends to avoid the occurrence of slackening during the wave cycle. In the paper, we developed the dynamics model for the proposed system. Energy gain has been calculated for realistic wave conditions and compared with the original float-counterweight device. The important differences from the float-counterweight system are that (1) both upward and downward motions of water surface can be utilized without problem. (2) slackening of energy gain and wire tension are effectively suppressed, and (4) for the same time averaged energy gain, the maximum wire tension is fairly lowered.