• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.4
• /
• pp.335-340
• /
• 2007

A new correlation between the Nusselt number based on modified heat transfer coefficient and Reynold number based on droplet-flow-rate was developed for the experimental data. The modified heat transfer coefficient was defined as ratio of wall heat flux to droplet subcooling. In the previous reports, the local heat flux of spray cooling in the film boiling region was experimentally investigated for the water spray region of $D_{max} = 0.0007{\sim}0.03m^3/(m^2s)$ . In the region near the stagnation point of spray flow, a new heat transfer correlation is recommended which shows good predictions for the water spray region of $D_x{\le}0.01m^3/(m^2s)$.

• Journal of ILASS-Korea
• /
• v.3 no.4
• /
• pp.50-57
• /
• 1998

The utilization of resonance should be considered to get the maximum effect of ultrasonic to atomize liquid. The ultrasonic generator, transducer, horn, and all attached parts are used to produce the resonance, and specially the characteristics of liquids such as liquid load, property, and etc., for the liquid atomization affinity are considered. In this study, the variable device of liquid load was made and distilled water and city water selected as experimental liquids were sprayed by a twin-fluid spray method and their diameters, distributions, and spray quantum of spray droplets were measured by the light scattering system. And all data were observed, compared and considered relatively. In results, a lot of phenomena of liquid atomization affinity by ultrasonic appeared in accordance with liquid loads, namely head h.

• The Korean Journal of Pesticide Science
• /
• v.9 no.4
• /
• pp.411-421
• /
• 2005

This study was carried out to establish rational methodologies for the use of pesticide formulations to be sprayed after water-dilution. Hardness and electric conductivity of six major river water and ground water sampled from 52 sites in major rice-growing areas across the country ranged from 5 to 324 ppm(av. 90 ppm) and from 0.038 to 1.078 dS/m(av. 0.265 dS/m), respectively, which are acceptable for diluent water of pesticides. The pH changes in pesticide spray solutions with time after preparation mainly depended on the pH of the water used for pesticide dilution. The surface tensions of pesticide spray solutions reduced slightly with time after preparation, irrespective of kinds of pesticide formulations. Suspensibility of WPs became worse with an increase in the hardness and salt concentrations of diluent water, even though the degree was negligible. Emulsion stability of ECs became worse with an increase in hardness and salt concentrations of diluent water. Degradation rates of the active ingredients of pesticide spray solutions 3 days after preparation were less than 5%, regardless of mixing or non-mixing of two or more pesticides. Consequently, the spray solutions of most pesticides were usable until two to three days after preparation unless physical properties deteriorated. The tank-mixing order of EC and WP formulations did not make any differences in all the physical properties of pesticide spray solutions. However, the proper order for the tank-mixing of compatible pesticides was WP, WG, SC, EC, and SL, because the order is easy to prepare the pesticide spray solutions. The efficacy of pesticide spray solutions on the respective target pathogens and insect pests of rice plants three days after preparation was recorded over 95% of that of 0 day, which was almost the same as that of the solutions applied punctually after preparation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.94-100
• /
• 2019

This study was conducted on a high-temperature/high-pressure washer in which low-pressure cold water in a boiler is heated to a temperature range of $70{\sim}80^{\circ}C$ by supplying diesel combustion heat. The high-temperature water is sent to a compressor to increase its pressure to 200 bar, thereby making high-temperature/high-pressure water, which is sprayed through a spray nozzle. In the results of this study, the spray temperature of the high-pressure washing was shown to be the highest when the ratio between the actual amount of combustible air and the theoretical amount of air was 1:1 and the energy consumption rate of the low-pressure boiler type high-pressure washer was shown to be much lower than that of the high-pressure boiler type high-pressure washer.

• Journal of ILASS-Korea
• /
• v.3 no.4
• /
• pp.8-15
• /
• 1998

The spray characteristics of emulsified fuel of W/O type has been experimentally investigated. The mixture of light oil and water by using ultrasonic energy adding system is used as the emulsified fuel. The SMD of sprayed droplet of emulsified fuel is measured by using the particle size analyzer. Major parameters of the present experimental study are the volume fraction of water in emulsified fuel, $0\sim30%$ by 5%, injection pressure, $10kg_f/cm^2\sim18kg_f/cm^2$ by $2kg_f/cm^2$, and the measurement distance, $10\sim100mm$, between injection nozzle tip and analyzer beam. Compared with light oil, the SMD of emulsified fuel is larger gradually by increasing the volume fraction of water in emulsified fuel, heightening injection pressure and increasing the spray distance. Also, In considering the fact that the pattern of drop size distribution of emulsified fuel is alike that of light oil, the real time spray in coincidence with making emulsified fuel by adding ultrasonic energy can stabilize spray pattern without modificating the injection system used by now.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.88-93
• /
• 2014

Nanofluids is that metallic or nonmetallic nanometer-sized particles are dispersed in liquid and they can be used in various fields to increase the heat transfer rate. This study conducted experiments to evaluate whether the cooling efficiency of nanofluids is better than that of water in spray cooling. A heated surface was designed and fabricated to make the temperature distribution be linear, which was confirmed by three thermocouple measurements under the heated surface. Spray cooling experiments were conducted using water, 0.2% wt. (weight), and 0.5% wt. $Al_2O_3$ nanofluids at the pressure of 0.2 MPa and 0.3 MPa. Based on the results, it is shown that the cooling efficiency of nanofluids is higher than that of water especially in the region of single phase heat transfer. As a result, we can expect that nanofluids can be used as efficient coolants in the cooling of electronic packages where the temperature of the heated surface is not high enough for boiling incipience.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.3
• /
• pp.283-292
• /
• 2023

Currently, spray coating has attracted interest in the mass production of anode catalyst layers for proton exchange membrane water electrolysis (PEMWE). The solvent in the spray ink is a critical factor for the catalyst dispersion in ink, the microstructure of the catalyst layer, and the PEMWE performance. Herein, various pure organic solvents were examined as a substitute for conventional isopropanol-deionized water (IPA-DIW) mixture for ink solvent. Among the polar solvents that exhibited better IrO₂ dispersion over nonpolar solvents, 2-butanol (2-BuOH) was selected as a suitable candidate. The PEMWE single cells were fabricated using 2-BuOH at various ionomer contents, spray nozzle types, and drying temperatures, and their performance was compared to the cells fabricated using a conventional IPA-DIW mixture. The PEMWE single cells with 2-BuOH solvent showed good performances comparable to the conventional IPA-DIW mixture case and highly durable performances under accelerated degradation tests.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.2053-2065
• /
• 2003

The current trend in automotive finishing industry is to use more electrostatic rotating bell (ESRB) need space to their higher transfer efficiency. The flow physics related with the transfer efficiency is strongly influenced by operating parameters. In order to improve their high transfer efficiency without compromising the coating quality, a better understanding is necessary to the ESRB application of metallic basecoat painting for the automobile exterior. This paper presents the results from experimental investigation of the ESRB spray to apply water-borne painting. The visualization, the droplet size, and velocity measurements of the spray flow were conducted under the operating conditions such as liquid flow rate, shaping airflow rate, bell rotational speed, and electrostatic voltage setting. The optical techniques used in here were a microscopic and light sheet visualization by a copper vapor laser, and a phase Doppler particle analyzer (PDPA) system. Water was used as paint surrogate for simplicity. The results show that the bell rotating speed is the most important influencing parameter for atomization processes. Liquid flow rate and shaping airflow rate significantly influence the spray structure. Based on the microscopic visualization, the atomization process occurs in ligament breakup mode, which is one of three atomization modes in rotating atomizer. In the spray transport zone, droplets tend to distribute according to size with the larger drops on the outer periphery of spray. In addition, the results of present study provide detailed information on the paint spray structure and transfer processes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.12 s.255
• /
• pp.1236-1242
• /
• 2006

The local heat flux of spray cooling in the film boiling region were experimentally investigated for the spray region of $D_{max}$ = $0.005{\sim}0.03m^3/(m^2s)$. A twin-fluid full cone spray nozzle was employed for the experiment and the distributions of droplet flow rates were obtained for air-water full cone sprays. A stainless steel block was cooled down from initial temperature of about $800^{\circ}C$ by full cone spray. In the region near the stagnation point, it was found that the experimental data are in good agreement with the results predicted from the correlations between the local heat transfer and the local droplet flow rate proposed in the previous report. However, it was found that the experimental data of $D_r$ > $0.01m^3/(m^2s)$ are a little smaller than the results predicted from the correlations.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 1996.04a
• /
• pp.288-288
• /
• 1996

The microcapsules containing ethanol in a water-soluble polymer shell could be formed by the spray-drying technique. A mixed solution of ethanol, water and a water-soluble polymer is spray-dried at the lowest possible temperature to obtain a powder product in which the water is substantially removed and the ethanol is encapsulated in water-soluble polymer shell because of the hydrophillic property of polymer and permeability difference between ethanol and water. In this study, the effect of sodium lauryl sulfate (SLS) on the ethanol content, ethanol encapsulation efficiency and yield were investigated to maximize the microencapsulation of ethanol.