• Journal of the Korean Chemical Society
• /
• v.43 no.4
• /
• pp.423-429
• /
• 1999

A spectrofluorimetric method for the determination of Fe(III) in aqueous solution with 4,5-dihydroxy-1,3-benzenedisulfonic acid(Tiron) as a fluorimetric reporter was developed. Tiron, which is very soluble in water,is a good fluorimetric reagent. However, when Tiron was complexed with Fe(III), the fluorescent intensity was decreased proportionally with the concentration of Fe(III) by a quenching effect. The excitation and fluorescene wavelength of Tiron showing the quenching effect by Fe(III) at pH 4.5 were 312 nm and 341 nm, respectively. The highest sensitivities were shown at Tiron concentration of $1.0{\times}10^{-2}M$. To enhance the quenching effect, the Fe(III)-Tiron complex solution was heated to 80$^{\circ}C$ for 90 minutes. As for Fe(III), the most interfering ion was Cu(II). The interference effects could be mostly eliminated by pH adjustment or by adding EDTA. The concentration ranges showing the linear response to Fe(III) was from $5.0{\times}10^{-7}M\;to\;6.0{\times}10^{-5}M$ With this proposed method, the detection limits of Fe(III) was $2.8{\times}10^{-6}M$. Recovery of Fe(lII) in a synthetic sample was almost quantitative. Based on experimental results, it is proposed that the above technique can be applied to the practical determination of Fe(III).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.12
• /
• pp.1887-1897
• /
• 2001

Korea Atomic Energy Research Institute (KAERI) launched an intermediate scale steam explosion experiment named "Test for Real Corium Interaction with water (TROI)" using reactor material to investigate whether the molten reactor material would lead to energetic steam explosion when interacted wish cold water at low pressure. The melt-water interaction experiment is performed in a pressure vessel with the multi-dimensional fuel and water pool geometry. The novel concept of cold crucible technology, where powder of the reactor material in a water-cooled cafe is heated by high frequency induction, is firstly implemented for the generation of molten fuel. In this paper, the lest facility and cold crucible technology are introduced and the results or the first series of tests were discussed. The 5 kg of molten ZrO$_2$jet was poured into the 67cm deep water pool at 30 ∼ 95 $\^{C}$. Either spontaneous steam explosions or quenching was observed. The morphology of debris and pressure wave profiles clearly indicate the differences between the two cases.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.179-193
• /
• 2000

Aluminium titanate (Al₂TiO5) with an excellent thermal shock resistant and a low the expansion coefficient was obtained by solid solution with MgO, SiO₂, and ZrO₂ in the Al₂TiO5 lattice or in the grain boundary solution through electrofusion in an arc furnace. However, these materials have low mechanical strength due to the presence of microcracks developed by a large difference in thermal expansion coefficients along crystallographic axes. Pure Al₂TiO5 tends to decompose into α-Al₂O₃ and TiO₂-rutile in the temperature range of 750-1300℃ that rendered it apparently useless for industrial applications. Several thermal shock tests were performed: Long therm thermal annealing test at 1100℃ for 100h; and water quenching from 950 to room temperature (RT). Cyclic thermal expansion coefficients up to 1500℃ before and after decomposition tests was also measured using a dilatometer, changes in the microstructure, thermal expansion coefficients, Young's modulus and strengths were determined. The role of microcracks in relation to thermal shock resistance and thermal expansion coefficient is discussed.

• Journal of Korea Foundry Society
• /
• v.3 no.3
• /
• pp.174-180
• /
• 1983

The matrix changes and graphite formation in high manganese cast iron (Fe-12Mn-3.5C) are studied with increasing nickel and silicon content. Also, the decomposition of carbides and graphite precipitation are studied by adequate heat treatment.The results obtained in this work are as follows. 1. In high manganese cast iron, fine flakes graphite appeared by adding 5 wt% nickel and A-type flakes graphite can be obtained by adding 7 wt% nickel. 2. Nodular graphite are obtained by graphite spheroidizing treatment with same melt. 3. In high manganese cast iron containing 7 wt% nickel, full austenitic matrix with nodular graphite can be achieved by water quenching after 10 hours' solution heat treatment at $1050^{\circ}C$ in case of containing 2.0 wt% silicon, and 6 hours' at the same temperature in case of containing 2.5 wt% silicon.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.263-263
• /
• 2009

The microtstructures and properties of alloys in the pseudo-binary $Bi_2Te_3-PbTe$ system were investigated as a first step towards the design of nanostructured materials with enhanced thermoelectric properties. The liquid alloys were cooled by water quenching method. Dendritic and lamellar structures were observed clearly by using environmental scanning electron microscope(eSEM) and electron probe micro analyzer(EPMA) take into account composition ratio between $Bi_2Te_3$ and PbTe. The compound $Pb_2Bi_6Te_{11}$ precipitated as a metastable phase under all conditions. The structure of those samples changed from dendritic to lamellar by increasing $Bi_2Te_3$ ratio of composition.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.6
• /
• pp.258-263
• /
• 2017

The effect of cooling rate on the damping capacity of pure Mg was studied. Two Mg samples with different cooling rates were prepared by heat treatment at 873 K for 24 h, followed by water quenching and by furnace cooling to room temperature, respectively. The average grain sizes of the Mg samples were almost identical regardless of the cooling rate, but more twins were observed in the sample with faster cooling rate. The calculated vacancy fraction was higher in the fast cooling sample than the slow cooling one. It is noted that the fast cooling sample exhibited lower damping capacity both in the strain-amplitude independent and strain-amplitude dependent regions. Higher values of vacancy concentration and number density of twins in the fast cooling sample are considered to be responsible for the deteriorated damping capacity in the strain-amplitude independent and strain-amplitude dependent regions, respectively.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.371-376
• /
• 2005

Phosphate glasses were prepared by melting quenching process, and glass formation and dissolution properties were studied. The glass forming region in the $K_2O-CaO-P_2O_5$ system is quietly agreed with the report by Mazurin OV et al. with $M_2O-M'O-P_2O_5$ system (M : monovalent cation, M'divalent cation). Conditionally these glasses have solubility from absorbing the moisture or water and then release elements with trace elements, and the thermal and chemical properties were controllable by the $CaO,\;K_2O,\;P_2O_5$ contents. In the abnormal glass properties, this paper showed the possibility the present glasses can be a good candidate for one component of the slow released agriculture fertilizer.

• Journal of the Korean Ceramic Society
• /
• v.16 no.4
• /
• pp.237-242
• /
• 1979

In order to improve hydration reactivity of blast furnace slag, it's composition was changed by adding of CaO. The slags were quenched in water at 1,400℃. Hydration reactivityof modified slags was studied by x-ray diffractometer, conduction calorimeter and so on. Experimental results were summarized as follows. 1. Glass content and hydration reactivity of slag depend significantly on quenching temperature of the slag melt. To enhance the reactivity, slag melts which belongs to Frenkel-type liquid, must be quenched above 1,300℃. 2. Vitrification of slag melts was confirmed as CaO/SiO2 ratio increased up to 1.57 with flux, 1.51 without flux, also their hydration reactivity was improved.

• Journal of Korea Foundry Society
• /
• v.30 no.3
• /
• pp.94-99
• /
• 2010

When the returned scrap of bulk amorphous alloy is remelted, impurities such as oxides and intermetallic compounds increase. Glass forming ability of its scrap is deteriorated remarkably. Melt fluxing technique is introduced to enhance the glass forming ability during melting and freezing of bulk amorphous alloys. Cu and Zr based alloys are chosen. Small pieces of these alloy scraps and $B_2O_3$ flux are put together in a quartz tube. Cyclic heating and cooling are done by induction heating and water quenching or air cooling. Melting fluxing was effective for both Cu-based and Zr-based alloy, and their glass forming abilities were improved with increasing the number of fluxing.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.113-124
• /
• 1992

The offshore industry created a need for quality wet weld repairs. Wet welding is a fast method of repair providing sound, structural quality welds. It requires less support equipment than a similar underwater dry weld repair or the alternative mechanical connections. Compared to welds made in air, underwater wet welds are plagued by increased hardness due to rapid quenching by the surrounding water. In this paper is described the experimntal study of improving the cooling rates of wet welds of TMCP steel plate by shielding around weld arc surroundings. The principal results of this experimental investigation can be summarized as follows : By shielding around weld arc surrounding, the cooling rates resulting from wet welds on TMCP steel plate could be lower than that of nonshielded wet welds and the fesibility on high quality of mecanical properties of wet weld on TMCP steel plate was carried out with shielded weld arc surrounding.