• Korean Journal of Agricultural Science
• /
• v.25 no.2
• /
• pp.260-270
• /
• 1998

The field tests were performed to suggest the rational method for stability evaluation of soft clay. The behavior of settlement-displacement obtained by field monitoring system was to compare and analyze the results of the observationed method, and to investigate the complex behavior of soft clay with filling height. The results of this study are summarized as follows. 1. The horizontal displacement was suddenly increased when physical properties of soft clay showed maximum values and the part of the turning point. The values of these properties were available to the fundamental data for stability evaluation. The shear deformation appeared that difference of the horizontal displacement was maximum values. 2. Although the stability of embankment by step filling showed the unstable part over the failure standard line, the embankment was confirmed stable. So the evaluation of the stability of embankment is reasonable to use the inclination of curve than failure standard line. 3. The horizontal displacement and relative settlement were increased as same ratio at improvement ground. Estimation of shear deformation using Terzaghi's modified bearing capacity should consider the relations of embankment load and undrained shear strength at nonimprovement ground, and minimum safety factor is recommended to use larger than 1.2. 4. Excess pore water pressure was increased with increasing of filling height and decreased with maintain the filling height. The embankment was unstable when filling height was exceed the evaluation standard line, and the behavior of excess pore water pressure and horizontal displacement could use as a standard of judgement of the filling velocity control because their behavior were agree with each other.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.2
• /
• pp.151-160
• /
• 2017

Growing demand and rapid development of the synthetic fiber rope in mooring system have taken place since it has been used in deep water platform lately. Unlike a chain mooring, synthetic fiber rope composed of lightweight materials such as Polyester(polyethylene terephthalate), HMPE(high modulus polyethylene) and Aramid(aromatic polyamide). Non-linear stiffness and another failure mode are distinct characteristics of synthetic fiber rope when compared to mooring chain. When these ropes are exposed to environmental load for a long time, the length of rope will be increased permanently. This is called 'the creep phenomenon'. Due to the phenomenon, The initial characteristics of mooring systems would be changed because the length and stiffness of the rope have been changed as time goes on. The changed characteristics of fiber rope cause different mooring tension and vessel offset compared to the initial design condition. Commercial mooring analysis software that widely used in industries is unable to take into account this phenomenon automatically. Even though the American Petroleum Institute (API) or other classification rules present some standard or criteria with respect to length and stiffness of a mooring line, simulation guide considers the mechanical properties that is not mentioned in such rules. In this paper, the effect of creep phenomenon in the fiber rope mooring system under specific environment condition is investigated. Desiged mooring system for a Mobile Offshore Drilling Unit(MODU) with HMPE rope which has the highest creep is analyzed in a time domain in order to investigate the effects creep phenomenon to vessel offset and mooring tension. We have developed a new procedure to an analysis of mooring system reflecting the creep phenomenon and it is validated through a time domain simulation using non-linear mooring analysis software, OrcaFlex. The result shows that the creep phenomenon should be considered in analysis procedure because it affects the length and stiffness of synthetic fiber rope in case of high water temperature and permanent mooring system.

• Journal of Korea Water Resources Association
• /
• v.36 no.4
• /
• pp.533-545
• /
• 2003

This study analyzed several storm events observed in the Seolma-chun basin to derive the characteristic velocity of GIUH (Geomophological Instantaneous Unit Hydrograph) as well as its variability. Especially, this study focused on the variation of characteristic velocity due to the change of rainfall characteristics. The IUH of the Seolma-chun basin was derived using the HEC-1, whose peak discharge and time were then compared with those of the GIUH to derive the characteristic velocities. The characteristics velocities were analyzed by comparing with the GcIUH (Geomorphoclimatic IUH) as well as the characteristics of rainfall. Results are summarized as follows. (1) The characteristic velocity of GIUH was estimated higher with higher variability than the GcIUH, but their trends were found similar (2) Total amount of effective rainfall (or, mean effective rainfall) well explains the characteristic velocity of GIUH. This could be assured by the regression analysis, whose coefficient of determination was estimated about 0.6. (3) The duration and the maximum intensity of rainfall were found not to affect significantly on the characteristic velocity of GIUH. The coefficients of determination were estimated less than 0.3 for all cases considered. (4) For the rainfall events used in this study, the characteristic velocities of GIUH were found to follow the Gaussian distribution with its mean and the standard deviation 0.402 m/s and 0.173 m/s, respectively. Most of the values are within the range of 0.4∼0.5 m/s, and its coefficient of variation was estimated to be 0.43, much less than that of the runoff itself (about 1.0).

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1253-1257
• /
• 2010

강원도 홍천군 내면에 위치한 비점오염 관리지역의 강우시 유출 특성을 파악하고, 비교하기위해 연구를 수행하였다. 2009년 6월부터 2009년 11월까지의 연구기간 중 강우량이 비교적 많은 7회의 강우사상에 대하여 단위면적당 유출량, 유량가중평균농도, 단위면적당 오염부하를 비교하며, 분석하였다. 강우사상별 단위면적당 총 유출량은 저감시설의 설치 유 무에 따라 명확한 경향이 나타나지 않았다. 자운천 유역의 SS, TP의 유량 가중평균농도는 각각 4.0~1440.4 mg/L와 0.024~0.267 mg/L의 범위로 나타났으며, 덕두원 유역의 SS, TP의 유량가중평균농도는 각각 6.2~1001.1 mg/L, 0.039~0.226 mg/L의 범위로 나타났다. 지령골 유역의 SS, TP의 유량가중평균농도는 각각 3.4~1050.6 mg/L, 0.08~0.342 mg/L의 범위로 조사되었다. 10차, 11차, 12차, 26차의 SS 항목에서는 비점오염 저감시설이 설치된 자운천과 덕두원 유역에 비해 다소 높은 것으로 나타났으며, TP는 대부분의 강우사상에서 지령골의 유량가중평균농도가 높았다. 자운천의 강우사상에 따른 SS의 단위면적당 오염부하는 0.24~1,397.85 kg/ha의 범위로 나타났으며, 덕두원과 지령골에서 산정된 SS의 단위면적당 오염부하는 각각 0.06~1,236.78 kg/ha와 0.29~894.81 kg/ha로서 8차와 9차 강우사상을 제외한 나머지 강우사상에서는 비점오염 저감시설이 설치되지 않은 지령골에서 더 많은 양이 발생하였다. TP의 경우 자운천과 덕두원 유역의 단위면적당 TP 오염부하는 각각 0.0006~0.33 kg/ha와 0.0005~0.21 kg/ha의 범위로 나타났으며, 지령골 유역의 강우사상에 따른 단위면적당 오염부하는 0.003~0.29 kg/ha의 범위로서 저감시설이 설치된 자운천과 덕두원 유역보다 높게 나타났다. 단위면적당 오염부하에 기초할 때, 비점오염 저감시설이 설치된 소유역에서 SS와 TP 항목에 대한 저감효과가 나타났다. 하지만 짧은 모니터링 기간과 자료의 부족으로 인해 비교 및 분석의 한계가 있다고 판단된다. 본 연구는 지속적인 모니터링으로 더 많은 자료가 확보될 때 비점오염 저감사업의 효과를 극대화시킬 수 있는 방안을 제시 할 수 있을 것으로 사료된다.

• Journal of Korea Water Resources Association
• /
• v.43 no.3
• /
• pp.245-256
• /
• 2010

We study the basic theory and applicability of the WQUAL block in the FFC2Q model and the characteristics of non-point pollutant loads during the early stage of runoff. Study is also performed on selection of the values of the related parameters and their effect on the simulation results. FFC2Q simulation results are compared for verification with the measured data for three rainfall events in the Gunja Subbasin and found to be similar to the measured data in peak-flows, total runoff volumes, total loads, peak concentrations and times of peak concentration. This model thus shows results very close to those applying the SWMM and MOUSE models, even though it uses simplified input data. Related to rainfall distribution, under the condition of Huff 1st quartile distribution the pollutant loads occurred earlier than under other conditions, and in the early stage of rainfall the BOD and COD loads increased faster than the SS loads. The NPS loads were concentrated in the early stage of rainfall and finally reached total loads, so the rainfall after that could not contribute so much to the NPS loads.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.4
• /
• pp.54-61
• /
• 2005

An aquifer thermal energy storage (ATES) system can be very cost-effective and renewable energy sources, depending on site-specific parameters and load characteristics. In order to develop the ATES system which has certain hydrogeological characteristics, understanding the thermohydraulic process of an aquifer is necessary for a proper design of an aquifer heat storage system under given conditions. The thermohydraulic transfer for heat storage was simulated according to two sets of simple pumping and waste water reinjection scenarios of groundwater heat pump system operation in a two-layered aquifer model. In the first set of the scenarios, the movement of the thermal front and groundwater level was simulated by changing the locations of injection and pumping wells in a seasonal cycle. However, in the second set the simulation was performed in the state of fixing the locations of pumping and injection wells. After 365 days simulation period, the shape of temperature distribution was highly dependent on the injected water temperature and the distance from the injection well. A small temperature change appeared on the surface compared to other simulated temperature distributions of 30 and 50 m depths. The porosity and groundwater flow characteristics of each layer sensitively affected the heat transfer. The groundwater levels and temperature changes in injection and pumping wells were monitored and the thermal interference between the wells was analyzed to test the effectiveness of the heat pump operation method applied.

• Journal of Korea Water Resources Association
• /
• v.51 no.10
• /
• pp.917-927
• /
• 2018

Seven heavy metal concentrations (As, Cd, Cr, Cu, Ni, Pb, Zn) were continuously analyzed for twenty rainfall events in 2017~2018 in an urban basin. The overall and dynamic correlations between runoff characteristics and heavy metal concentrations were examined. The peak metal concentration generally appeared in the initial runoff but found to be delayed when the rainfall intensity was low. The rainfall duration had no relationship with either heavy metal concentrations or their total mass. Dynamics of heavy metal mass (load), with the exception of Cu and Zn, showed strong correlation with the 30 minute rainfall intensity (0.60~0.88) and runoff volume (0.74~0.89). While event mean concentration (EMC) showed positive correlation (0.54~0.73) with antecedent dry days (ADD), no significant relationship was found between runoff volume and pollutant concentration. This implies that the pollutants built up on the surface during dry days are washed off even with low rainfall energy. The dynamics of heavy metal and TSS concentrations showed good correlation (0.68~0.87). This result shows that the metals are transported along with solid particles as adsorbate in surface runoff. Regular street sweeping will reduce significant amount of heavy metal loads in urban surface runoff.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.37-43
• /
• 2017

Domestic sandwich panel buildings are widely used on walls and roofs of factories and warehouse facilities. Factory and warehouse facilities have high fire load and rapid spread of fire due to their use characteristics, leading to large fires. Due to the characteristics of materials, walls and roofs are collapsed, resulting in life damage and property damage. In this regard, this study examined domestic and international standards of sprinkler facilities to prevent ignition of sandwich panel walls. Also, in order to check whether the fire was prevented by installing the head on the wall of the sandwich panel, the fire test was carried out with 10 cm, 60 cm, and 120 cm from the wall along the sprinkler head installation standard of domestic fire safety standards. As a result of the fire test, it was confirmed that the sandwich panel was prevented from igniting when the head of water pressure 0.1 MPa and water quantity K-80 was installed. According to the separation distance, it was impossible to measure the temperature at 10 cm, but at 60 cm, At the maximum temperature of $525^{\circ}C$ and 120 cm, the maximum temperature of the wall of the sandwich panel was measured as $276^{\circ}C$. As a result of the fire test, considering the fire point of 450 degrees Celsius in the fire test of the sandwich panel, the distance from the sandwich panel wall to the combustible is more than 120 cm.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.574-574
• /
• 2016

유역으로 유입되는 오염물질의 발생원은 점오염원과 비점오염원으로 구분할 수 있으며 점오염원의 경우 생활하수, 산업폐수, 그리고 축산폐수에 대해 처리시설 확충 및 기술개발을 통해 관리하고 있다. 비점오염원에서의 오염물질 유출은 토지이용, 강우, 불특정적인 오염물질 투입상태 등에 따라 다르며, 지역적 특성에 영향을 받기 때문에 불확실성이 고려되어야 한다. 특히 농촌지역에서의 비점오염은 접근이 어렵고 관리주체가 모호하여 좀처럼 규명되지 않았으며, 전국적으로 그 영향이 정량화되지 않아 실질적인 관리 및 대책마련에 어려움이 있었다. 특히, 가축분뇨의 발생으로부터 처리, 자원화에 이르기까지 각 관리체계에 있어서 축산비점오염의 배출경로와 수계오염부하량, 수질환경 영향을 정밀하게 분석하여 향후 대책마련을 위한 기초자료를 확보할 필요가 있다. 또한 전국적으로 비점오염이 수계에 미치는 영향과, 그 중 축산비점오염의 영향을 면밀히 분석하여 향후 정책 및 제도개선을 위한 과학적 기초자료로서 활용할 필요가 있다. 따라서 본 연구에서는 축산 밀집 지역을 대상으로 오염원 조사를 통해 강우시 비점오염 모니터링 지점을 선정 하였으며, 년5회씩 강우 모니터링을 하여 기초데이터를 축적 하였다. 대상지역은 강원도 횡성군에 위치한 일리천 유역이며 농가 수는 총 90개의 농가가 위치하고 있는데 그 중 돼지 1,467마리, 한우 1,957마리, 젖소 581마리, 개 2,880마리, 닭 75,000마리, 사슴 4마리로 조사되었다. 대상유역을 대상으로 배출부하량을 조사한 결과 BOD 배출부하량은 총 509.3 kg/day, T-N 배출부하량은 총 331.5 kg/day, T-P 배출부하량은 총 28.3 kg/day로 조사되었다. 유출특성을 파악하기 위하여 유량가중평균농도(Event Mean Concentration, EMC)를 산정한 결과 BOD의 경우 MW-4에서 1.2 mg/L - 7.2 mg/L, MW-5에서 0.8 mg/L - 6.3 mg/L, MW-7에서 0.7 mg/L - 5.2 mg/L의 범위를 보였다. T-N의 경우 MW-4에서 1.426 mg/L - 5.321 mg/L, MW-5에서 1.205 mg/L - 4.27 mg/L, MW-7에서 0.989 mg/L - 3.859 mg/L의 범위를 보였다. T-P의 경우 MW-4에서 0.245 mg/L - 0.632 mg/L, MW-5에서 0.236 mg/L - 0.596 mg/L, MW-7에서 0.213 mg/L - 0.521 mg/L의 범위를 보였다. 본 연구에서 EMC를 산정한 방법은 평시 수질 및 유량을 정하는 기준에 따라 값이 많이 달라질 수 있다. 따라서 합리적으로 평시 부하량을 제외하고 강우시의 영향을 파악할 수 있는 EMC 산정방법에 대한 추가적인 고찰이 필요할 것으로 사료된다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.243-254
• /
• 2019

In this study, problems of the waterproofing methods in which water leakage occurs in the upper slab of the underground parking lot of apartment houses and the requirements considering the characteristics of the upper slab, and selected the appropriate performance(proposal) for the composite polyurea process are reviewed. As a result of the study, it is necessary to review performance such as responsiveness to upper slab of the multi-unit underground parking lot that is comprised of (1) crack and behavior responsiveness, (2) surface integrity, (3) vertical watertight stability, (4) pressure layer construction, (5) impact and pressure response and (6) vehicle moving load. As a result of evaluating 5 items corresponding to the requirements for the soft and hard complex polyurea, all of them were found to meet the conditions, and each materials were improved by compounding the materials that had problems when applying a single-ply method, thereby clarifying the advantages and disadvantages of the material property. However, in order to apply to the actual site, additional evaluation on site applicability such as mock-up evaluation should be conducted, and subsequent studies on the applicability of the market through review of economic feasibility and maintenance is required.