• 한국농공학회지
• /
• 제16권3호
• /
• pp.3477-3491
• /
• 1974

Following are the results of the study on the property of falling permeation of stratified soil in the close state under existence of stagnant water on a soil layer. 1. When on the stratified soil a least permeating layer was put on the soil layer the load Pressure was present owing to appearance of saturation close state driving decrease of the pressure in the lower layer, on the other hand when the least permeating layer was placed under the layer the lower least permeating layer pressure was decreased. 2. In the case of least permeating layer the variation of current gradient according to the respective level after treating the layer was enormous and due to usal storage phenomena for the Kl layer which was coarse that was trifle. 3. The permeability of the respective layer of stratified soil in the close state died not always coincide with that of single layer. 4. Generally Zunker's equation of average permeability was valid but actually calculated permeating velocity after treating the layer of stratified soil was seriously differ from the measured value owing to the variation of current gradient, especially when the pressure head at the layer boundany was discontinuous the validity of the equation of average permeability was seemed to be doubtful. 5. The permeating velocity of stratified soil was regulated by the least permeating layer, i.e. it is thought to be rational to estimate the value by calculating the current gradient with its proper permeability, pressure headon the layer and its thickness.

• 전기화학회지
• /
• 제16권1호
• /
• pp.39-45
• /
• 2013

물 관리는 저온에서 작동하는 고분자전해질 연료전지의 성능에 큰 영향을 미친다. 가스확산층(gas diffusion layer, GDL)은 반응 가스를 촉매층의 반응영역으로 확산시키는 역할을 한다. 연료전지의 작동온도가 $60{\sim}80^{\circ}C$이기때문에, 고전류 밀도에서 생성된 물은 액적을 형성한다. 만약 생성된 물이 적절하게 제거되지 않는다면, GDL 내의 기공을 막게 되고 연료전지 성능이 저하된다. 본 연구에서는 플러딩 현상을 막기 위해 마이크로채널 GDL 을 제안하였다. 기존 GDL과 마이크로채널 GDL을 3차원으로 구현하여 공기 속도, 물속도, 접촉각의 변화에 따른 물의 이송을 연구하였다. 전산해석 결과를 통해 마이크로채널 GDL에서는 낮은 유동 저항으로 인해 물이 빠르게 제거되는 것으로 나타났다. 그러므로, 마이크로채널 GDL이 가스채널과 GDL 내부의 물 제거에 효율적임을 알 수 있다.

• International Journal of Concrete Structures and Materials
• /
• 제3권1호
• /
• pp.15-23
• /
• 2009

Over about 30% of problems in construction is related to water-leaking, and the loss from this problem can incur as much as three times the cost of initial construction. Thus, water vapor pressure is known to be the primary cause of defective waterproofing. Accordingly, the theories on the relationship between water pressure and temperature as well as damp-proofing volume of concrete and the change in vapor pressure volume were reviewed and analyzed in this study by making test samples after spraying a dampness remover and applying waterproofing materials to the prepared test specimens. The result of measuring water vapor pressure with the surface temperature of the waterproofing (fluid-applied membrane) layer at the experimental temperature setting of about $10^{\circ}C$, which is the annual average temperature of Seoul, indicated that (1) the temperature of the fluid-applied membrane elevated to about $40^{\circ}C$, and the water vapor pressure generated from the fluid-applied membrane was about 0.03 N/mm 2 when the surface temperature of the waterproofing layer was raised to about $80^{\circ}C$. (2) when the temperature of the fluid-applied membrane of the waterproofing layer was raised from $30^{\circ}C$ to $35^{\circ}C$, water vapor pressure of about 0.01 N/mm 2 was generated, and (3) when a thermal source was applied to the fluid-applied membrane (waterproofing) layer, the temperature increased from $35^{\circ}C$ to $40^{\circ}C$, and approximately $0.005\;N/mm^2$ of water vapor pressure was generated.

• 한국포장학회지
• /
• 제23권1호
• /
• pp.9-15
• /
• 2017

수증기 및 산소에 대한 차단성이 개선된 PVA-BA 코팅 조성액의 포장소재로의 적용가능성을 확인하기 위하여 콤마 코팅과 라미네이션 공정을 이용하여 PET/PVA-BA/OPP 다층필름을 제조하였다. PCT 전 후의 PET/PVA-BA/OPP 다층필름의 기체, 수증기 차단특성 및 인장강도를 확인하였고 이를 PA/PA/EVOH/PP 다층필름의 물성과 비교하였다. PVA내 BA 함량이 증가함에 따라 물성이 증가하는 것을 확인할 수 있었지만, PCT 후 PET/PVA-BA/OPP 다층필름의 산소, 수증기 차단특성 및 인장강도는 감소하는 경향을 보였다. 이는 PVA-BA층 내 증가한 가교밀도와 관련이 있는 것으로 판단된다. 또한, 조미김을 이용한 저장특성분석에서, PET/PVA-BA/OPP다층필름은 PP/Al-metallized PP 다층필름에 비해 조미김의 지방산화를 야기시키는 요인을 효과적으로 억제하는 것으로 판단된다. 하지만, PP/Al-metallized PP 다층필름에 비해 PET/PVA-BA/OPP 다층필름의 상대적으로 높은 수분투과특성 때문에 Aw에 큰 장점을 확인하지 못하였다. 따라서, 물성 극대화 및 포장소재로 적용을 위해서는 PET/PVA-BA/OPP 다층필름 내 수분 차단성 향상에 대한 추가적인 연구가 필요하다는 것을 확인하였다.

• 한국환경과학회지
• /
• 제20권9호
• /
• pp.1069-1078
• /
• 2011

The environmental changes related to hypoxic water mass were investigated at Gamak bay in summer times, June, July and August 2006. The hypoxic water mass was found, in first, at the northern area of Gamak bay on 27 June. This water mass has been sustained until the end of August and disappear on 13 September. In Gamak bay, the hypoxic water mass was closely related to geography. During the formation of oxygen deficiency, changes in dissolved nutrients was studied and found that on surface layer and lower layer, DIN were 0.80 ${\mu}M$~19.8 ${\mu}M$(6.03 ${\mu}M$) and 1.13 ${\mu}M$～60.83 ${\mu}M$(10.66 ${\mu}M$), and DIP were 0.01 ${\mu}M$～0.92 ${\mu}M$(0.24 ${\mu}M$), and 0.01 ${\mu}M$～3.57 ${\mu}M$(0.49 ${\mu}M$), respectively, far higher distribution on lower layer of the water where hypoxic water mass was occurred. The configuration of phosphorus was analyzed to figure out the possibility of release of phosphorus from sediments. It was found that the Labile-Phosphorus, which is capable of easy move to water layer by following environmental change was found more than 70%. Therefore, in Gamak bay, it was found that the possibility of large amount of release of soluble P into the water, while hypoxic water mass was occurred in deep layer was higher. It is suggested that DIP in the northern sea of Gamak bay mainly sourced from the soluble P from lower layer of the waters where hypoxic water mass was created more than that from basin. However, existence form of phosphorus in sediments during normal times, not during creation of hypoxic water mass, needs further study.

• 한국표면공학회지
• /
• 제48권6호
• /
• pp.349-353
• /
• 2015

In this paper, arc thermal spray coating was conducted onto the SS400 steel using Inconel 625 wires in order to improve the durability of marine steel structures, and then investigated cavitation damage behavior of Inconel 625 coating layer in sea water. For the Inconel 625 coating layer, surface hardness appeared similar to that of existing high velocity oxy-fuel coating technology with 380~480 HV, but the porosity of about 6 % was larger relatively. During the cavitation experiment, pit damages were originated and grown at the rough surface and pore defect area of Inconel 625 coating layer. And, after the 72 hours of experimental time, weight loss of Inconel 625 coating layer exhibited gradually increasing tendency due to surface damage effect of the undercut.

• 한국지형학회지
• /
• 제25권4호
• /
• pp.77-88
• /
• 2018

Wetlandsis developing on the lava plateau in Eundae-ri, even though there are no majorstreams into this area. As a result of drilling, 1~2m clay layer is founded under the superficial formations of the wetland, which are the main reasons for formation of the wetlands by limiting vertical drainage. The clay layer's Granulometry/XRD show very different characteristics from in situ weathering of basalt, and since 2~3cm of sand layer exist within the profile, the clay layer seems to be supplied and deposited from outside through surface/sheet flows. To keep the wetlands sustainably, the supply of water into the wetlands has to be increased by restoring the surface/sheet flow which is limited or deformed by pavement road.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.160-160
• /
• 2010

Organic electronic devices require a passivation layer to ensure sufficient lifetime. Specifically, flexible organic electronic devices need a barrier layer that transmits less than $10^{-6}\;g/m^2/day$ of water and $10^{-5}\;g/m^2/day$ of oxygen. To increase the lifetime of organic electronic device, therefore, it is indispensable to protect the organic materials from water and oxygen. Severe groups have reported on multi-layerd barriers consisting inorganic thin films deposited by plasma enhenced chemical deposition (PECVD) or sputtering. However, it is difficult to control the formation of granular-type morphology and microscopic pinholes in PECVD and sputtering. On the contrary, atomic layer deoposition (ALD) is free of pinhole, highly uniform, conformal films and show good step coverage. In this study, the passivation layer was deposited using single-process PEALD. The passivation layer, in our case, was a bilayer system consisting of $Al_2O_3$ films and a $TiO_2$ buffer layer on a poly (ether sulfon) (PES) substrate. Because the deposition temperature and plasma power have a significant effect on the properties of the passivation layer, the characteristics of the $Al_2O_3$ films were investigated in terms of density under different deposition temperatures and plasma powers. The effect of the $TiO_2$ buffer layer also was also addressed. In addition, the water vapor transmission rate (WVTR) and organic light-emitting diode (OLEDs) lifetime were measured after forming a bilayer composed of $Al_2O_3/TiO_2$ on a PES substrate.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권4호
• /
• pp.374-380
• /
• 2015

본 연구에서는 연료전지 캐소드 가스 확산층에서의 물의 영향이 연료전지 성능에 미치는 영향을 검토하기 위하여 연료전지 스택의 부하 변동에 따른 가스 확산층에서의 2상 현상의 구현이 가능한 동적 모델을 개발하였다. 개발된 모델에 대하여 2상의 영향에 의한 연료전지 부하변동에 따른 연료전지 스택 성능, 가스 확산층 내부에서의 물 증기와 산소의 농도분포, 가스 확산층의 두께 및 다공성이 연료전지 스택 전압에 미치는 영향에 대하여 검토하였다. 그 결과 본 연구의 범위 내에서 연료전지 스택 전압은 부하에 관계없이 2상 모델이 1상 모델보다 낮아짐을 알 수 있다. 촉매층 부근 가스 확산층에서의 산소 농도는 가장 낮고 물 증기의 농도는 가장 높음을 알 수 있었다. 또한, GDL의 두께가 두꺼울수록 GDL의 다공성이 작을수록 연료전지 스택 전압이 낮아짐을 알 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.163-164
• /
• 2014

This study is conducted for prevent spread of penetration water and water leakage through non-woven fabric between PVC sheet and PVC sheet in the PVC composite waterproofing sheet of a multi-layer structure. For this, carry out absorption amount test to confirm spread resistance performance after manufacturing PVC composite waterproofing sheet of a multi-layer structure using water-repellency processed non-woven fabric. As a result of test, weight of water-repellency processed non-woven fabric increased to 1.178g, Compared with beginning and there are not penetration water.