• 한국터널지하공간학회 논문집
• /
• 제18권2호
• /
• pp.155-164
• /
• 2016

본 연구에서는 지상구조물 건설을 위하여 흙막이 벽체를 이용하여 지하굴착이 이루어진 지역에 근접하여 새로운 지하공간이 신설될 때, 지하굴착과 흙막이 벽체간의 이격거리에 따른 흙막이 벽체에 작용하고 있던 토압의 변화 및 지표 침하 변화를 실험적으로 연구하였다. 지하공간 굴착 단계별로 흙막이 벽체의 토압 변화 및 지표 침하를 측정할 수 있는 길이 160 cm, 높이 120 cm의 모형 토조를 제작했다. 실험은 균일하게 조성된 사질토 지반에서 하부 지반에 변위를 가하고, 수직한 흙막이 벽체의 토압 변화 및 지표면 침하를 확인하는 방식으로 수행하였다. 모형실험은 인접한 지하공간 굴착에 따른 흙막이 벽체의 높이별 토압을 측정하기 위하여 흙막이 벽체를 모사하는 우측 벽체 10개 및 지하공간 굴착을 모사하는 하부 벽체 5개로 구성하고 하부벽체를 거동시킴으로서 지하굴착을 모사하였다. 실험 결과, 하부 1단 벽체의 거동 시에는 흙막이 벽체의 토압에 변화가 발생하였으나, 하부 3단의 경우는 지하 굴착이 흙막이 벽체와 충분히 이격되어 토압변화가 크게 발생하지 않았다. 하부 1단 벽체를 굴착한 결과, 우측 하단부 벽체 주변의 응력이 감소되고, 우측 중간부 벽체 주변으로 응력이 재분배되는 아칭현상을 증명할 수 있었다.

• 한국지반공학회논문집
• /
• 제19권1호
• /
• pp.191-199
• /
• 2003

강성 옹벽에 작용하는 주동토압은 뒷채움재에서 발생하는 아칭효과로 인하여 삼각형이 아닌 비선형의 분포형태를 보인다. 따라서 뒷채움재에서 발생하는 아칭효과를 고려함으로써 평행이동하는 강성옹벽에 작용하는 주동토압의 비선형 분포를 산정할 수 있는 새로운 토압산정식이 제안되었다. 본 논문에서는 $\phi$와 \delta$, 그리고 옹벽의 높이가 새로운 제안식에서 계산되는 토압의 크기와 분포형태에 미치는 영향을 알아보기 위하여 매개변수 분석을 수행하였다. 그리고 제안된 토압산정식에 대한 정확도를 검증하기 위하여 새로운 제안식에서 얻어진 결과들이 기존의 시험결과 및 기존 제안식들의 결과들과 비교되었다. 예측치와 측정치의 비교를 통해서 새로운 토압산정식은 평행이동하는 강성 벽체에 작용하는 주동토압의 크기와 분포형태에 대하여 만족스런 결과를 주는 것으로 나타났다. 또한 새로운 토압산정식의 사용성을 높이기 위하여 수정 주동토압계수와 주동토압의 작용점 높이에 대한 간편한 설계도표가 제시되었다.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.722-733
• /
• 1999

The wall pressure fluctuations of a turbulent boundary layer over a flat plate have been investigated in an anechoic wind tunnel facility. The anechoic wind tunnel consists of acoustically-lined duct, muffler, and splitter-type silencer for noise suppression and vanes for reducing head losses involved. To improve spectra characteristics in high frequency range, a 1/8" pressure-type microphone sensor, which has a pin-holed cap of various diameters, was employed in this experiment. It was shown that the pin-holed microphone sensor with a dimensionless diameter $d^+$ of 7.1 resolved the high frequency pressure fluctuations most effectively among ones with various pin-hole diameters. The measured wall pressure spectra in terms of three types of scaling parameters were in good agreement with other experimental and numerical results. The pressure events of high amplitude were found to contribute to total fluctuating pressure energies in the turbulent boundary layer significantly and supposed to radiate to the far-field effectively.

• Journal of Mechanical Science and Technology
• /
• 제15권4호
• /
• pp.492-499
• /
• 2001

The characteristics of Prand시-Meyer expansion of supersonic flow with condensation along a wavy wall in a channel are investigated by means of experiments and numerical analyses. Experiments are carried out for the case of moist air flow in an intermittent indraft supersonic wind tunnel. The flow fields are visualized by a Schlieren system and the distributions of static pressure along the upper wavy wall are measured by a scanning valve system with pressure transducers. In numerical analyses, the distributions of streamlines, Mach lines, iso-pressure lines, and iso-mass fractions of liquid are obtained by the two-dimensional direct marching method of characteristics. The effects of stagnation temperature, absolute humidity, and attack angle of the upper wavy wall on the generation and the locations of generation and reflection of an oblique shock wave are clarified. Futhermore, it is confirmed that the wavy wall plays an important role in the generation of an oblique shock wave and that the effect of condensation on the flow fields is apparent.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.245-246
• /
• 2012

The possibility that self-ignition can be generated near an obstacle is high in practical applications such as a hydrogen car. In this paper, experimental investigations were suggested to understand the effects of a wall on self-ignition phenomena through high-speed images. The results showed that the existence of a wall could not change the ignition phenomena itself irrespective of wall height and burst pressure. However, when a strong flame was induced in the tube, a wall could promote the flame stabilization.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2631-2636
• /
• 2008

The most components and piping of the secondary side of domestic nuclear power plants were manufactured carbon-steel and low-alloy steel. Flow accelerated corrosion leads to wall thinning (metal loss) of carbon steel components and piping exposed to the flowing water or wet steam of high temperature, pressure, and velocity. The feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which increases as operating time progress. Several nuclear power plants in Korea have also experienced wall thinning damage in the shell wall around the impingement baffle. This paper describes the comparisons between the numerical analysis results using the FLUENT code and the experimental results based on down-scaled experimental facility. The experiments were performed based on several types of impingement baffle plates which are installed in low pressure feedwater heater.

• 한국지반공학회논문집
• /
• 제31권9호
• /
• pp.69-78
• /
• 2015

유한한 크기의 벽체에 주동변위가 발생하면 배면지반은 3차원 형태의 쐐기가 형성되고 벽체는 3차원 주동토압이 작용하게 된다. 기존 연구에서는 3차원 쐐기형상을 측정하거나 단일파괴체로 가정하여 3차원 주동토압의 합력을 산정하였다. 또한 이들 연구에서는 파괴형상과 3차원 주동토압의 크기 및 산정방법에 따라 서로 다른 결과가 도출되었다. 본 연구에서는 모형실험을 통해 벽체의 크기를 폭(w)과 높이(h) 비인 종횡비(h/w)로 나타내고, 이에 따른 3차원 주동토압의 크기와 분포를 측정하고 기존 3차원 토압연구 결과와 비교하였다. 연구결과 한계상태 벽체변위(s)는 벽체높이(h)의 약 0.12% 크기일 때 발생하였고, 합력의 크기는 Karstedt(1982)와 유사하였다. 벽체의 주동토압분포는 종횡비(h/w)가 1.2이상일 때에는 상부와 하부는 상대적으로 작고, 지표 하부 0.50~0.55h지점에서 가장 큰 포물선 형태로 나타났다. 종횡비(h/w) 0.2~2.7 범위에서 3차원 주동토압의 크기를, 고전토압이론을 이용하여 계산한 2차원 주동토압과 비교하여 종횡비(h/w)에 따른 2차원 토압 대비 3차원 주동토압 감소계수(${\alpha}$)를 구할 수 있는 도표로 제안하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1206-1215
• /
• 2008

In this study, the equivalent pressure acting on the face of drilled hole was determined by back analysis. This analysis was continued until the difference between the displacement directly measured during field test construction of CGS and the displacement evaluated by numerical analysis was below 10 percent, and the affect of diaphragm wall adjacent to grout bulb was evaluated by numerical analysis using the equivalent pressure. From the analysis results, it was observed that the increase of the pressure acting on the diaphragm wall was greater at reclaimed sandfill layer than silty clay layer during the installation of CGS. Two methods were adopted to reduce the pressure acting on the diaphragm wall. One is installing of trench between diaphragm wall and grout bulb, the other is pre-installing of CGS before construction of diaphragm wall. From the numerical analysis results, above two methods can be considered as an effective method to reduce the pressure. It was analyzed that the amount of reduction of the pressure and the displacement are 689.8% and 564.6%, respectively, in the case of adopting the trench method, and 463.7% and 214.0%, respectively, in the case of adopting pre-installing of 3 columns CGS.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 춘계 학술대회논문집
• /
• pp.134-143
• /
• 2001

Viscous solutions of supersonic jet impinging on a flat plate normal to the flow are simulated using three-dimensional Navier-Stokes solver. The jet impinging flow structure exhibits such complex nature as shock shell, plate shock and Mach disk depending on the flow parameters. Among others, the dominant parameters are the ratio of the nozzle exit pressure to the ambient pressure and the distance between the nozzle exit plane and the impinging plane. In the present study, the nozzle contour and the pressure ratio are held fixed, while the jet impinging distance is varied to illuminate the characteristics of the jet plume with the distance. As the plate is placed close to the nozzle at 3D high, the computed wall pressure at or near the jet center oscillates with large amplitude with respect to the mean value. Here D is the nozzle exit diameter. The amplitude of wall pressure fluctuations subsides as the distance increases, but the maximum pressure level at the plate is achieved when the distance is about 4D high. The frequency of the wall pressure is estimated at 6.0 kHz, 9.3 kHz, and 10.0 kHz as the impinging distance varies from 3D, 4D, to 6D, respectively.

• 한국산업융합학회 논문집
• /
• 제5권3호
• /
• pp.247-254
• /
• 2002

This study has researched the following conclusion to compare to the existing theory and to examine lateral earth pressure, which have measured to add incremental load on sandy soil, and were different in types of compaction by modeling earth pressure test. Lateral earth pressure by incremental load shows that it is increasing at depth forty four centimeters as 2/3H point for wall high, and under 2/3 H point the variation of earth pressure on incremental load is not conspicuous. Therefor, the more a position of surcharge load is close with fixed wall, the more a variation of lateral earth pressure marks considerably. According to relative compaction density of soil, lateral earth pressure turns up larger effective value for layer compaction test to a thickness of thirty three centimeters than layer compaction test to a thickness of twenty centimeters by the roller.