• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.2019-2026
• /
• 2003

Spray and combustion characteristics of a dump-type ram-combustor equipped with a V-gutter flame holder were experimentally investigated. Spray penetrations with a change in airstream velocity, air stream temperature, and dynamic pressure ratio were measured to clarify the spray characteristics of a liquid jet injected into the subsonic vitiated airstream, which maintains a highly uniform velocity and temperature. An empirical equation was modified from Inamura's equation to compensate for experimental conditions. In the case of insufficient penetration, the flame in the ram-combustor was unstable, and vice versus in the case of sufficient penetration. When the flame holder was not equipped, the temperature at the center of the ram-combustor had a tendency to decrease due to the low penetration and insufficient mixing. Therefore, the temperature distribution was slanted to the low wall of the ram-combustor. These trends gradually disappeared as the length of the combustor became longer and the flame holder was equipped. Combustion efficiency increased when the length of the combustor was long and the flame holder was equipped. Especially, the effect of the flame holder was more dominant than that of the combustor length in light of combustion efficiency.

• 대한기계학회논문집B
• /
• 제31권1호
• /
• pp.51-61
• /
• 2007

This paper presents numerical and theoretical studies of acoustic wave interactions in slightly compressible liquids within piezoelectrically driven inkjet print heads. The interconnected flow channels may cause jet crosstalk, resulting in poor printing quality. It should be reduced by modifying the channel structure with the acoustic wave interactions considered. Compressible gas flow driven by the sudden movement of a top wall in the channel is calculated using Flow3D and is validated with the narrow gap theory. Limited compressibility model of the Flow3D is employed to calculate pressure waves of slightly compressible ink flow. It is found that reducing restrictor width can damp out the jet crosstalk by inhibiting the pressure wave propagation. The degree of crosstalk has been quantified using the maximum values of cross-correlations between neighboring channels and a critical channel dimension for acceptable crosstalk has been proposed. This finding is verified by drop visualization experiments using silicon-micromachined piezo inkjet print heads that are fabricated by our group.

• 대한기계학회논문집B
• /
• 제20권11호
• /
• pp.3573-3588
• /
• 1996

The flow through a centrifugal compressor impeller was calculated using the 3-dimensional Navier-Stokes solution method. A control volume method based on a rotating curvilinear coordinate system was used to solve the time-averaged Navier-Stokes equations, and a standard k-.epsilon. model was used to obtain eddy viscosity. Numerical results and experimental data were compared for the overall performance of the impeller, the pressure distributions along the shroud wall and the detailed flowfields at the design and off-design conditions, which showed good coincidence. The flow through the impeller is complex with the curvature of the streamlines and rotation. The development of secondary flows and the jet-wake flow characteristics, which is the main source of flow loss, was discussed. Calculation results show quite different patterns as the flow rate changes.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 PARALLEL CFD 2006
• /
• pp.395-397
• /
• 2006

Air interlacing serves to protect the yarn against damage, strengthens inter-filament compactness or cohesion, and ensures fabric consistency. The air interlacing nozzle is used to introduce intermittent nips to a filament yarn so as to improve its performance in textile processing. The effect of various interlacing nozzle geometries on the interlacing process was studied. The geometries of interlacing nozzles with single or multiple air inlets located across the width of yarn channels are investigated. The basis case is the yarn channel, with a perpendicular main air inlet in the middle. Other cases have main air inlets, slightly inclined double sub air inlets, The yarn channel cross sectional shapes are either semicircular or rectangular shapes. The compressed impinging jet from the main air inlet hole hits the opposing bottom wall of the yarn channel, is divided into two branches, joins with the compressed air coming out from sub air inlet at the bottom and creates two free jets at both ends of the yarn channel. The compressed air movement in the cross-section consists of two opposing directional vortices. The CFD-FASTRAN flow parallel solver was used to perform steady simulations of impinging jet flow inside of the interlace nozzles. The vortical structure and the flow pattern such as pressure contour, particle traces, velocity vector plots inside of interlace nozzle geometry are discussed in this pater.

• 한국추진공학회지
• /
• 제7권3호
• /
• pp.45-52
• /
• 2003

원추형 초음속 노즐 확산부에 이차유동이 음속으로 분출될 때 나타나는 노즐 내부 유동장에 대한 수치적 연구가 이루어졌다. 대수-난류모델과 $\kappa$-$\varepsilon$ 모델을 사용한 레이놀즈-평균 Navier-Stokes 방정식을 계산함으로서 노즐 내부에서 나타나는 충격파와 경계층의 간섭에 의한 3 차원 유동장을 해석하였다. 얻어진 수치해석의 결과는 동일한 조건에서 수행된 실험결과와 잘 일치하고 있음이 판명되었다. 이차유동의 분출압력 변화가 충격파와 경계층의 간섭과 함께 노즐내부 유동장 구조에 미치는 영향을 평가하였다. 아울러 충격파 간섭 후방에서 나타나는 와류유동 구조와 벽면 압력분포에 관한 정보를 얻었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.5-8
• /
• 2010

본 논문에서 연구하고자 하는 분사기는 다단 연소 사이클 엔진 연소기에 적용하는 분사기이다. 본 분사기에서 연료는 접선홀을 통해 와류 형상으로 분무되며, 예연소기에서 생성된 산화제 과잉 가스는 중앙에서 jet의 형태로 공급된다. 이러한 기체-액체 분사기의 상압/고압환경에서의 분무특성 및 분사기의 리세스에 따른 분무특성의 차이를 알아보았다. 이러한 결과들은 향후 다단 연소 사이클 엔진 개발의 기본 데이터로 활용될 수 있을 것이다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.192-197
• /
• 2004

Recently, fluidic thrust vectoring methods have been preferably employed to control the movement of propulsive systems due to relatively simpler design and lower cost than mechanical thrust vectoring methods. For An application of the thrust vectoring to flight bodies, it is necessary to understand very complicated exhaust flows which are often subject to shock waves and boundary layer separation. But researches for the thrust vector control using counterflow have been few. In the present study, experiments have been performed to investigate the characteristics of supersonic jets controlled by a thrust vectoring method using counterflow. The primary jet is expanded through a two-dimensional primary nozzle shrouded by collars, and is deflected by the suction of the air near nozzle into an upper slot placed between the primary nozzle and the upper collar. A shadowgraph method is used to visualize the supersonic jet flowfields. Primary nozzle pressure ratios and suction nozzle pressure ratios are varied from 3.0 to 5.0, and from 0.2 to 1.0 respectively. The present experimental results showed that, for a given primary nozzle pressure ratio, a decrease in the suction nozzle pressure ratio produced an increased thrust vector angle. As the suction nozzle pressure ratios were increased and decreased, the hysteresis of the thrust vectoring was observed through the wall pressure distributions

• Nuclear Engineering and Technology
• /
• 제48권1호
• /
• pp.72-86
• /
• 2016

A steam explosion may occur during a severe accident, when the molten core comes into contact with water. The pressurized water reactor and boiling water reactor ex-vessel steam explosion study, which was carried out with the multicomponent three-dimensional Eulerian fuel-coolant interaction code under the conditions of the Organisation for Economic Co-operation and Development (OECD) Steam Explosion Resolution for Nuclear Applications project reactor exercise, is presented and discussed. In reactor calculations, the largest uncertainties in the prediction of the steam explosion strength are expected to be caused by the large uncertainties related to the jet breakup. To obtain some insight into these uncertainties, premixing simulations were performed with both available jet breakup models, i.e., the global and the local models. The simulations revealed that weaker explosions are predicted by the local model, compared to the global model, due to the predicted smaller melt droplet size, resulting in increased melt solidification and increased void buildup, both reducing the explosion strength. Despite the lower active melt mass predicted for the pressurized water reactor case, pressure loads at the cavity walls are typically higher than that for the boiling water reactor case. This is because of the significantly larger boiling water reactor cavity, where the explosion pressure wave originating from the premixture in the center of the cavity has already been significantly weakened on reaching the distant cavity wall.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.17-24
• /
• 2006

The turbulent flow field characteristics of a gun-type gas burner with and without a duct were investigated under the isothermal condition of non-combustion. Vectors and mean velocities were measured by hot-wire anemometer system with an X-type hot-wire probe in this paper. The turbulent flow field with a duct seems to cause a counter-clockwise recirculation flow from downstream to upstream due to the unbalance of static pressure between a main jet flow and a duct wall. Moreover, the recirculation flow seems to expand the main jet flow to the radial and to shorten it to the axial. Therefore, the turbulent flow field with a duct increases a radial momentum but decreases a axial momentum. As a result, an axial mean velocity component with a duct above the downstream range of about X/R=1.5 forms a smaller magnitude than that without a duct in the inner part of a burner, but it shows the opposite trend in the outer part.

• 한국수소및신에너지학회논문집
• /
• 제30권3호
• /
• pp.243-250
• /
• 2019

In this study, to ensure the safety of the packaged hydrogen refueling system, the improvement plan was derived by using 3-dimensional CFD program (FLACS). We also confirmed the effectiveness of risk reduction and the suitability of safety standard. By ventilation performance evaluation according to the position of the vent, it demonstrated that the vent should be installed at the ceiling to safely ventilate without stagnation of the leaked gas. In case of ventilation system according to KGS standard, risk situation could be resolved after about 5 minutes in the worst leaked condition. The result showed that jet fire and explosion inside the packaged system could affect the surrounding facilities. This proves that the standard for installing flame detectors, emergency shut down system and protection wall is appropriate.