• Wind and Structures
• /
• v.22 no.2
• /
• pp.253-272
• /
• 2016

The paper concerns with the method and results of wind tunnel investigations of the Strouhal number (St) of a stationary iced cable model of cable-supported bridges with respect to different angles of wind attack. The investigations were conducted in the Climatic Wind Tunnel Laboratory of the Czech Academy of Sciences in $Tel{\check{c}}$. The methodology leading to the experimental icing of the inclined cable model was prepared in a climatic section of the laboratory. The shape of the ice on the cable was registered by a photogrammetry method. A section of an iced cable model with a smaller scale was reproduced with a 3D printing procedure for subsequent aerodynamic investigations. The St values were determined within the range of the Reynolds number (Re) between $2.4{\cdot}10^4$ and $16.5{\cdot}10^4$, based on the dominant vortex shedding frequencies measured in the wake of the model. The model was oriented at three principal angles of wind attack for each of selected Re values. The flow regimes were distinguished for each model configuration. In order to recognize the tunnel blockage effect the St of a circular smooth cylinder was also tested. Good agreement with the reported values in the subcritical Re range of a circular cylinder was obtained. The knowledge of the flow regimes of the airflow around an iced cable and the associated St values could constitute a basis to formulate a mathematical description of the vortex-induced force acting on the iced cable of a cable-supported bridge and could allow predicting the cable response due to the vortex excitation phenomenon.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.157-164
• /
• 2015

The present work performs three-dimensional flow calculations based on Reynolds Averaged Navier-Stokes (RANS) and Delayed Detached Eddy Simulation (DDES) to investigate the flow field of a transonic rotor (NASA Rotor 37) at near-stall condition. It is found that the DES approach is likely to predict well the complex flow characteristics such as secondary vortex or turbulent flow phenomenon than RANS approach, which is useful to describe the flow mechanism of a transonic compressor. Especially, the DES results show improvement of predicting the flow field in the wake region and the model captures reasonably well separated regions compared to the RANS model. Besides, it is discovered that the three-dimensional vortical flows after the vortex breakdown from the rotor tip region are widely distributed and its vortex structures are clearly present. Near the rotor leading edge, a part of the tip leakage flows in DES solution spill over into next passage of the blade owing to the separation vortex flow and the backflow is clearly seen around the trailing edge of rotor tip. Furthermore, the DES solution shows strong turbulent eddies especially in the rotor hub, rotor tip section and the downstream of rotor trailing edge compared to the RANS solution.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.14-26
• /
• 1989

This paper describes the method of statistical analysis and its programs for predicting the ship's powering performance. The equation for the wavemaking resistance coefficient is derived as the sectional area coefficients by using the wavemaking resistance theory and its regression coefficients are determined from the regression analysis of the model test results. The equations for the form factor, wake franction and thrust deduction fraction are derived by purely regression analysis of the principal dimensions, sectional area coefficients and model test results. The statistical analyses are performed using the various descriptive statistic and stepwise regression analysis techniques. The powering performance prognosis program is developed to cover the prediction of resistance coefficients, propulsive coefficients, propeller open-water efficiency and various scale effect corrections.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.235-238
• /
• 2005

The unsteady supersonic flow over two- and three-Dimensional cavities has been analyzed by the integration of unsteady Reynolds-Averaged Navier-Stokes(RANS) with the k - w turbulence model. The unsteady flow is characterized by the periodicity due to the mutual relation between the shear layer and the internal flow in cavities. Numerical method is upwind TVD scheme based on the flux vector split with the Van Leer limiters, and time accuracy is used explicit 4th stage Runge-Kutta scheme. Cavity flows are Comparison of two- and three-dimensional. The cavity has a L/D ratio of 3 for two-dimensional case. and same L/D and W/D ratio is 1 for three-dimensional case. The Mach and Reynolds numbers are held constant at 1.5 and 450000 respectively. For the three-dimensional case, the flow field is observed to oscillate in the 'shear layer mode' with a feedback mechanism that follow Rossiter's formula. On the other hand, the self-sustained oscillating flow transitions to a 'wake mode' for the two-dimensional simulation, with more violent fluctuations inside the cavity.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.12-19
• /
• 2011

Drawing on its extensive experience with natural disasters, Japan has been dispatching Japan Disaster Relief (JDR) team to disaster-stricken countries to provide specialist assistance in rescue and medical operations. The JDR team has assisted in the wake of disasters including the 2004 Indian Ocean Earthquake and the 2008 Sichuan Earthquake in China. Information about the affected area is essential for a rapid disaster response. However, it can be difficult to gather information on damages in the immediate post-disaster period. To help overcome this problem, we have built on an Earthquake Damage Estimation System. This system makes it possible to produce distributions of the earthquake's seismic intensity and structural damage based on pre-calculated data such as landform and site amplification factors for Peak Ground Velocity, which are estimated from a Digital Elevation Model, as well as population distribution. The estimation result can be shared with the JDR team and with other international organizations through communications satellite or the Internet, enabling more effective rapid relief operations.

• Wind and Structures
• /
• v.11 no.5
• /
• pp.377-389
• /
• 2008

An experimental investigation has been conducted to determine the effectiveness of base shield plates in reducing the drag of a rough circular cylinder in a cross flow at Reynolds numbers in the range $3{\times}10^4{\leq}Re{\leq}10.5{\times}10^4$. Three model configurations were investigated and compared: a plane cylinder (PC), a cylinder with a splitter plate (MC1) and a cylinder fitted with base shield plates (MC2). Each configuration was studied in the sub and supercritical flow regimes. The chord of the plates, L, ranged from 0.22 to 1.50D and the cavity width, G, between the plates was in the range from 0 to 0.93D. It is recognized that base shield plates can be employed more effectively than splitter plates to reduce the aerodynamic drag of circular cylinders in both the sub- and supercritical flow regimes. For subcritical flow regime, one can get 53% and 24% drag reductions for the MC2 and MC1 models with L/D=1.0, respectively, compared with the PC model. For supercritical flow regime however, the corresponding drag reductions are 38% and 7%.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.24 no.3
• /
• pp.17-24
• /
• 1987

The present paper describes the results of the cooperative experimental study organized by the Resistance Committee of the Korea Towing Tank Conference, which aims to improve model testing technique and accuracy and to self-evaluate their own capabilities. A Series 60, $C_b=0.60$ model was tested at the towing tanks of Korea Institute of Machinery & Metals, Hyundai Maritime Research Institute, Seoul National University, and Inha University. Results for total resistance, wave pattern analysis, wave pattern analysis, wave profile, trim & sinkage and wake measure ments are presented.

• Wind and Structures
• /
• v.20 no.2
• /
• pp.327-347
• /
• 2015

This paper investigates the effects of Reynolds number (Re) on the aerodynamic characteristics of a twin-deck bridge. A 1:36 scale sectional model of a twin girder bridge was tested using the Wall of Wind (WOW) open jet wind tunnel facility at Florida International University (FIU). Static tests were performed on the model, instrumented with pressure taps and load cells, at high wind speeds with Re ranging from $1.3{\times}10^6$ to $6.1{\times}10^6$ based on the section width. Results show that the section was almost insensitive to Re when pitched to negative angles of attack. However, mean and fluctuating pressure distributions changed noticeably for zero and positive wind angles of attack while testing at different Re regimes. The pressure results suggested that with the Re increase, a larger separation bubble formed on the bottom surface of the upstream girder accompanied with a narrower wake region. As a result, drag coefficient decreased mildly and negative lift coefficient increased. Flow modification due to the Re increase also helped in distributing forces more equally between the two girders. The bare deck section was found to be prone to vortex shedding with limited dependence on the Re. Based on the observations, vortex mitigation devices attached to the bottom surface were effective in inhibiting vortex shedding, particularly at lower Re regime.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.10 no.2
• /
• pp.140-149
• /
• 2000

In industrial field, there are several operations where a horizontal unidirectional airflow is used to control airborne contaminants. When a worker is immersed in a uniform freestream, a recirculating airflow can be created downstream of the worker by the phenomenon of boundary layer seperation. If the contaminant source and the breathing zone are within this near-wake region, high exposure may occur. The investigation for the effect of contaminant source location on worker exposure was performed by using CFD(Computational Fluid Dynamics). The airflow field was numerically calculated by assuming a steady flow and using the standard $k-{\varepsilon}$ turbulence model. As the results were compared with experimental data, the applicability of CFD was successfully verified. Subsequently, the breathing zone concentrations of the worker were predicted and compared with experimental data. The effects of contaminant density and turbulence intensity of freestream on worker exposure were evaluated.

• Journal of computational fluids engineering
• /
• v.7 no.4
• /
• pp.35-41
• /
• 2002

The projectile afterbodies for zero-lift drag reduction has been analyzed using the Navier-Stokes equations with the κ-εturbidence model. The numerical method of a second order upwind scheme has been used on an unstructured adaptive grid system. Base drag reduction methods that have been found effective on axisymmetric bodies are boattailing, base bleed, base combustion, locked vortex afterbodies and multistep afterbodies. In this paper, turbulence flow and pressure charateristics have been studied for geometries of multistep afterbodies. The important geometrical and flow parameters relevant to the design of such afterbodies have been identified by step number, length and height. The flow over multistep aftoerbodies or base have many kinds of compressible flow characteristics including expansion waves at the trailing edge, recompression waves, separation and recirculating flow in the base region, shear flow and wake flow. The numerical results have been compared and analyzed with the experimental data. The flow characteristics have been clearly shown.