• Wind and Structures
• /
• v.35 no.1
• /
• pp.1-20
• /
• 2022

This research work presents an experimental study's outcomes to reveal the impact of an O-ring on the flow control over a sphere placed in a turbulent boundary layer. The investigation is performed quantitatively and qualitatively using particle image velocimetry (PIV) and dye visualization. The sphere model having a diamater of 42.5 mm is located in a turbulent boundary layer flow over a smooth plate for gap ratios of 0≤G/D≤1.5 at Reynolds number of 5 × 10³. Flow characteristics, including patterns of instantaneous vorticity, streaklines, time-averaged streamlines, velocity vectors, velocity fluctuations, Reynolds stress correlations, and turbulence kinetic energy (), are compared and discussed for a naked sphere and spheres having O-rings. The boundary layer velocity gradient and proximity of the sphere to the flat plate profoundly influence the flow dynamics. At proximity ratios of G/D=0.1 and 0.25, a wall jet is formed between lower side of the sphere and flat plate, and velocity fluctuations increase in regions close to the wall. At G/D=0.25, the jet flow also induces local flow separations on the flat plate. At higher proximity ratios, the velocity gradient of the boundary layer causes asymmetries in the mean flow characteristics and turbulence values in the wake region. It is observed that the O-ring with various placement angles (𝜃) on the sphere has a considerable alteration in the flow structure and turbulence statistics on the wake. At lower placement angles, where the O-ring is closer to the forward stagnation point of the sphere, the flow control performance of the O-ring is limited; however, its impact on the flow separation becomes pronounced as it is moved away from the forward stagnation point. At G/D=1.50 for O-ring diameters of 4.7 (2 mm) and 7 (3 mm) percent of the sphere diameter, the -ring exhibits remarkable flow control at 𝜃=50° and 𝜃=55° before laminar flow separation occurrence on the sphere surface, respectively. This conclusion is yielded from narrowed wakes and reductions in turbulence statistics compared to the naked sphere model. The O-ring with a diameter of 3 mm and placement angle of 50° exhibits the most effective flow control. It decreases, in sequence, streamwise velocity fluctuations and length of wake recovery region by 45% and 40%, respectively, which can be evaluated as source of decrement in drag force.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.891-898
• /
• 2007

Optimal aerodynamic design for the pitch-controlled horizontal axis wind turbine and its aerodynamic performance for various pitch angles are performed numerically by using the blade element momentum theory. The numerical calculation includes effects such as Prandtl‘s tip loss, airfoil distribution, and wake rotation. Six different airfoils are distributed along the blade span, and the special airfoil i.e. airfoil of 40% thickness ratio is adopted at the hub side to have structural integrity. The nonlinear chord obtained from the optimal design procedure is linearized to decrease the weight and to increase the productivity with very little change of the aerodynamic performance. From the comparisons of the power, thrust, and torque coefficients with corresponding values of different pitch angles, the aerodynamic performance shows delicate changes for just $3^{\circ}$ increase or decrease of the pitch angle. For precisive pitch control, it requires the pitch control algorithm and its drive mechanism below $3^{\circ}$ increment of pitch angle. The maximum torque is generated when the speed ratio is smaller than the designed one.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.43-54
• /
• 2004

A visualization study was carried out to investigate the effects of phase difference qualitatively by examining wake pattern on the phase difference of a dragonfly type wing model. The model was built with scaled-up, flapping wings composed of a paired wing with fore- and hind-wings in tandem that mimick the wing form of a dragonfly. The present study was conducted by using the smoke-wire technique and an electronic device below the tandem wings was mounted to find the exact wing position angles. Uncertainties in wing position angle are about $\pm$$1.0^{\cire}$ and instantaneous wing positional angle varies from $-16.5^{\cire}$ to $+22.8^{\cire}$. The tests were made at phase differences between the fore-wing and hind-wing at $0^{\cire}$, $90^{\cire}$, $180^{\cire}$ and $270^{\cire}$. The results show that Karman vortex structures were produced at phase differences of $90^{\cire}$, $180^{\cire}$ and $270^{\cire}$, but Karman vortex structures were not observed at the phase difference of $0^{\cire}$.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.6
• /
• pp.424-432
• /
• 2023

This study deals with the design of a safety device around a leisure boat propeller. The safety device is to be designed to minimize performance degradation attached to propulsors in coastal waters. These devices, important for preventing propeller accidents, negatively gives influence boat performance, especially at higher speeds. In order to minimize the negative effect, the accelerating ducts, normally used in ESDs (Energy Saving Devices) have been chosen as a safety device. The present study aims to design an optimal duct (minimizing negative effect) through the parametric study. Based on the Marine 19A nozzle, the nozzle's thickness and angle were varied to obtain the optimum parameter in the preliminary design by the computational fluid dynamics program Star-CCM+ Ver. 15.02. In the detailed design, a NACA 4-digit Airfoil shape resembling the Marine 19A by modification at the trailing edge was chosen and the optimum shape was chosen according to variation of camber, thickness, and incidence angle for optimization. The optimally designed duct shows a speed decrease of about 10% in the sea trial result, which is much smaller than the normal speed decrease of at least 30%. The present designing method can give wide applications to the leisure boat because the wake is almost the same due to using the outboard propulsor.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.3
• /
• pp.285-295
• /
• 2016

A contact strip shape of a high speed train pantograph system was optimized with CFD to increase the aerodynamic performance and stability of contact force, and the results were validated by a wind tunnel test. For design of the optimal contact strip shape, a Kriging model and genetic algorithm were used to ensure the global search of the optimal point and reduce the computational cost. To enhance the performance and robustness of the contact strip for high speed pantograph, the drag coefficient and the fluctuation of the lift coefficient along the angle of attack were selected as design objectives. Aerodynamic forces were measured by a load cell and HWA (Hot Wire Anemometer) was used to measure the Strouhal number of wake flow. PIV (Particle Image Velocimetry) was adopted to visualize the flow fields. The optimized contact strip shape was shown a lower drag with smaller fluctuation of vertical lift force than the general shaped contact strip. And the acoustic noise source strength of the optimized contact strip was also reduced. Finally, the reduction amount of drag and noise was assessed when the optimized contact strip was applied to three dimensional pantograph system.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.80-91
• /
• 2009

In this study, a prediction theory for specific noise that is the overall characteristic of the fan has been proposed. This theory is based on total pressure prediction and broadband noise prediction. The specific noises of two forward curved fans with different number of blades were predicted. The flow around the impeller having 120 blades (MF120) was more biased at a certain positions than the impeller with 40 blades (MF40). An effective domain of the energy conversion of MF40 has extended overall than MF120. The total pressure was affected by the slip factor and pressure loss caused by the vortex flow. The suppression of a major pressure drop by the vortex flow and expansion of the effective domain for energy conversion contributed to an increase in the total pressure of MF40 at the design point. The position of maximum relative velocity was different for each fan. The relative velocity of MF120 was less than that of MF40 due to the deviation angle. The specific noise of MF120 was 2.7 dB less than that of MF40 due to the difference in internal flow. It has been quantitatively estimated that the deceleration in the relative velocity contributed to the improvement in the overall performance.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.159-165
• /
• 2007

The Characteristics of the flowfield around two circular cylinders in tandem arrangement was investigated by PIV. Strouhal numbers. velocity vectors and velocity profiles were observed at centre-to-centre space ratios of P/D= 1.5. 2.0 and 2.5, and Reynolds number of $Re=3.0{\times}10^3{\sim}5.0{\times}10^3$. As the results the Strouhal numbers measured in the rear region of the cylinder of wake side were decreased with the space ratios. The flow between two cylinders was almost stagnated and the size of the stagnated region was larger in the close side than in the far side of the front cylinder. The direction of vortex between two cylinders was opposed each other with the small difference(${\alpha}\;{\pm}1.0^{\circ}$) of the attack angle ${\alpha}$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.2
• /
• pp.131-136
• /
• 2008

The characteristics of the flowfields around two circular cylinders in various arrangements were investigated by PIV. In tandem arrangement, the Strouhal numbers measured in the rear region of the cylinder of wake side were decreased with the space ratios, the flow between two cylinders was almost stagnated and the closer to upstream cylinder, the larger the width of the stagnated region was. The direction of vortex between two cylinders was opposed each other with the small difference(${\alpha}$=${\pm}1.0^{\circ}$) of the attack angle . In side by side arrangement, the flow velocity between two circular cylinders were increased with the space ratios.

• Journal of Ship and Ocean Technology
• /
• v.10 no.2
• /
• pp.1-10
• /
• 2006

Numerical analysis of viscous flow around twin-skeg hull forms was conducted according to the variations of distance between skegs and vertical skeg inclinations by using a hydrodynamic analysis system, WAVIS. Six twin-skeg hull forms were derived by combining three distances between skegs (16m, 20m, 24m) and four vertical skeg angles ($0^{\circ},\;10^{\circ},\;15^{\circ},\;20^{\circ}$). It is found that the better resistance performance can be obtained with larger vertical skeg angle and smaller skeg distance for the present test cases. It also can be seen that the same trend is true for the nominal wake distributions in the propeller plane. Those tendencies were confirmed by the experimental results of MOERI. It is shown that numerical analysis can be a useful and practical tool for the evaluation and improvement of hydrodynamic performances for the complex stern hull forms with twin skegs.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.388-393
• /
• 2001

An experimental study is conducted to investigate the interaction of vortices over a delta wing with leading edge extension(LEX) through the off-surface flow visualization and the 5-hole probe measurements of the wing wake region. Especially, the application of a new visualization technique is employed by ultrasonic humidifier water droplet and laser beam sheet. The results, both the off-surface visualization and the 5-hole probe, show that LEX tends to stabilize the vortices of the delta wing up to the high angle of attack even though the model is yawed. With increasing yaw, the windward leading edge vortex moves inward, and closer to the wing surface, while the leeward vortex moves outwards and away from the wing surface. The vortex interaction is promoted in the windward side, and is delayed in the leeward side.