• Clean Technology
• /
• v.19 no.3
• /
• pp.219-225
• /
• 2013

Environment-friendly and surfactant-free aqueous cleaning agents have been developed in order to solve various problems generated by surfactants in the aqueous cleaning agents. Aqueous surfactant-free cleaning agents, S-1 and S-2 have been formulated with water-soluble solvents such as propylene glycol and propylene glycol ether on their main components and with some additives. These solvents were chosen because of their good solubility in water and excellent solubility of fluxes which are major contaminants of printed circuit board in the electronic industry. Physical properties of the formulated and the imported cleaning agents were measured to predict their cleaning performance, and their cleaning abilities of flux and solder contaminants were evaluated under the various ultrasonic frequencies by a gravimetric method. The measurement results show that the physical properties of cleaning agent V are generally similar with those of formulated cleaning agents S-1 and S-2. Both the cleaning agent V and the formulated cleaning agents S-1 and S-2 showed similar trends that their pH decrease in the beginning and then increases later on with the increase of their dilution in water. It is considered that the wetting indices of the cleaning agents calculated with experimental values do not not have any influence on their cleaning ability. In ultrasonic cleaning tests under three ultrasonic frequencies of 28, 45, and 100 kHz, their best performances of cleaning solder and flux were obtained at 45 kHz and 28 kHz, respectively, and the cleaning performance of the formulated cleaning agents S-1 and S-2 was better than that of the cleaning agent V. However, in the case of the recommended diluted concentration of 25 wt% cleaning solution, the cleaning performance of the cleaner V for solder and flux was better in the initial stage of cleaning compared to the formulated cleaners. And it may be concluded that the formulated cleaning agents S-1 and S-2 can be applied to cleaning of solder and flux in the industry, based on the experimental results in this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.226-226
• /
• 2008

지난 10여년 동안 Sn-3.0Ag-0.5(wt%)Cu 합금은 대표 무연솔더 조성으로 다양한 전자제품의 실장 및 접합에 적용되어 왔으며, 그 신뢰성 역시 충분히 검증된 바 있다. 그러나 최근 Ag 가격의 급격한 상승과 솔더 접합부의 내 충격 신뢰성을 보다 향상시키고자 하는 업계의 동향은 Ag의 함량이 낮은 무연솔더 조성의 적용 확대를 유도하고 있다. 이에 따라 본 연구자들은 저 Ag 함유 무연슬더로 Sn-1.2Ag-0.5Cu-0.4In 조성을 제안한 바 있는데, 이는 Sn-3.0Ag-0.5Cu 조성 이상의 solderability를 가지면서도 그 금속원료 가격이 약 20% 가량 저렴한 특징을 가진다. 또한 열 싸이클링 (cycling) 테스트를 통한 슬더 조인트의 신뢰성을 평가한 결과, Sn-3.0Ag-0.5Cu에 크게 뒤떨어지지 않는 양호한 특성이 관찰되었다. 따라서 본 연구에서는 열 싸이클링 테스트와 더불어 최근 그 중요성이 지속적으로 커지고 있는 내 충격 신뢰성 평가 시험을 실시하여 개발된 4원계 무연솔더 조성의 기계적 특성을 기존 무연솔더 조성과 비교, 분석해 보았다. 각 솔더 조성은 솔더 볼 형태로 제조되어 CSP(Chip Scale Package) 상에 범핑 (bumping)되었으며, CSP를 PCB(Printed Circuit Board) 상에 실장하는 공정에서도 Sn-3.0Ag-0.5Cu 및 Sn-1.2Ag-0.5Cu-0.4In의 두 종류의 솔더 페이스트가 사용되었다. 본 연구에서의 내 충격 신뢰성 시험에는 자체 제작한 rod drop 시험기를 사용하였는데, 고정된 CSP 실장 board의 후면 부위를 일정한 높이에서 추를 반복적으로 자유 낙하시켜 급격한 충격을 주는 방식으로 실험을 실시하였다. 이 때 추의 무게는 30g, 낙하 높이는 10cm 였으며, 추의 낙하 시 측정된 board 의 휨 변위량은 약 0.7mm로 측정되었다. 사용된 CSP와 PCB 는 모두 daisy chain 방식으로 연결되어 있기 때문에 저항측정기를 사용한 간단한 실시간 저항 측정 방법으로 시험 이력에 따른 파단부의 발생 시점과 대략의 위치를 손쉽게 확인할 수 있었다. 솔더 조인트의 파단 기준 저항값으로 $1000\Omega$을 설정하였으며. 각 조건 당 5 개 이상의 샘플에 대해 평가를 실시한 후 그 평균값을 조사하였다. 시험 결과 제안된 Sn-1.2Ag-0.5Cu-0.4In 조성은 대표적인 저 Ag 함유 조성인 Sn-1.0Ag-0.5Cu에 비해서는 떨어지는 내 충격 신뢰성을 나타내었지만, 우수한 연성에 기인하여 Sn-3.0Ag-0.5Cu 조성에 비해서는 약 2 배 이상 우수한 신뢰성이 관찰되었다. 또한 CSP의 실장 시 Sn-3.0Ag-0.5Cu보다 Sn-1.2Ag-0.5Cu-0.4In 조성 솔더 페이스트를 적용한 경우에서 보다 우수한 내 충격 신뢰성을 나타내어 기본적으로 개발된 Sn-1.2Ag-0.5Cu-0.4In 솔더 페이스트가 Sn-3.0Ag-0.5Cu 조성의 기존 솔더 페이스트 보다 내 충격 신뢰성이 우수함을 검증할 수 있었다. 각 조성의 솔더 조인트를 $150^{\circ}C$ 에서 500시간 aging한 후 실시한 내 충격 신뢰성 평가에서는 모든 조성에서 그 신뢰성이 급감하는 경항을 나타내었으나, Sn-1.2Ag-0.5Cu-0.4In가 Sn-l.0Ag-0.5Cu보다도 그 상대적인 신뢰성이 우수한 것으로 관찰되었다. 이와 같이 aging 후 실시하는 충격시험은 가장 실제적인 상황과 유사한 조건이므로 상기의 실험 결과는 매우 고무적이었으며, 이에 대한 보다 면밀한 분석이 요청되었다. 마지막으로 파면 및 미세조직 관찰을 통하여 각 조성에서의 충격 파단 특성을 비교, 분석해 보았다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.708-715
• /
• 2017

Recently, in order to meet the stricter emission regulations, the proportion of after-treatments for vehicles and vessels has been increasing gradually. The objective of this study is to investigate the improvement of $CH_4$ reduction ability of natural gas oxidation catalyst (NGOC), which reduces toxic gases emitted from CNG buses. Thirteen NGOCs were prepared, and the conversion performance of noxious gases according to the type of supports, the loading amount of noble metal, and surfactant and aging were determined. Support Zeolite supported on No. 3 $NGOC(1Pt-1Pd-3MgO-3CeO_2/(46TiO_2+23Al_2O_3+23Zeolite)$ is an anionic alkali metal/earth metal component that improved the oxidation reactivity between CO and NO and noble metal dispersion, and thus enhanced the $CH_4$ reduction ability. As the loading amount of Pd, a noble metal with a high selectivity to $CH_4$, was increased, the number of reaction sites was increased and the ability to reduce $CH_4$ was improved. No. 11 $NGOC(1Pt-1Pd-3MgO-3CeO_2/(Z20+Al80)$(pH=8.5), to which nitrate surfactant had been added, exhibited well dispersed catalyst particles with no agglomeration and improved the $CH_4$ reduction ability by 5-15%. The $NGOC(2Pt-2Pd-3Cr-3MgO/90Al_2O_3)$(48h aging), which was mildly thermal aged for 48h, increased the $CH_4$ reduction ability to about 10% or less as compared with No. 12 NGOC(Fresh).

• Applied Biological Chemistry
• /
• v.14 no.1
• /
• pp.9-18
• /
• 1971

In order to obtain basic information on the production of single cell protein from petroleum, more than 400 yeast strains were isolated from various soil samples in Korea utilizing petroleum hydrocarbon as the sole carbon source. A yeast strain showing the highest cell yield among the isolated strains was selected and identified. The optimal culture condition was searched in the flasks shaken throughout the procedure. And the growing characteristics for the selected yeast strain and chemical analysis of the yeast cell component were carried out. The results obtained were as follows: 1. The selected yeast strain was identified as Candida curvata and we named it Candida curvata-SNU 70. 2. The composition of the medium proposed for the present yeast strain is: Light Gas Oil 30ml, Urea 400mg, Ammonium sulfate 100mg, Potasium phosphate (monobasic) 670mg, Sodium phosphate (dibasic) 330mg, Magnesium sulfate 500mg, Calcium carbonate 3g, Yeast extract 50mg, Tween 20 0.05ml, Tap water 1,000ml. 3. Other culture conditions employed for the yeast were pH 5.5-7.0, temp. $30^{\circ}C$ under an affluent aerobic state. 4. Addition of light gas oil in portions to the culture media as the growth proceeded was more effective, especially in the cultivation on the higher oil concentration media. 5. Studies on the propagation of the yeast cells in the light gas oil medium revealed that the yeast has the lag phase lasted 16 hours and the logarithmic growth phase covered 16 to 28 hours. The specific growth rate was about $0.22\;hr^{-1}$ and doubling time was 3.2 hrs. during the logarithmic growth phase. 6. Under the cultural condition employed, the cell yield against the amount of light gas oil (wt%) was 16.1% and the protein content of the dried yeast cells was 48.4%.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.1 s.47
• /
• pp.15-29
• /
• 2006

Synthetic Mn-tourmalines (tsilaisite) were obtained by hydrothermal synthesis under the condition of 2 Kbar, $375{\sim}700^{\circ}C$, and 50 day-run-time with complete substitution of Mg in dravite by Mn (Mn%=0, 25, 50, 75, and 100%). They are all 6 samples containing Mn-tourmaline with some amounts of albite, spessartine, rhodocrosite, phlogopite etc, showing different synthetic condition of temperature and Mn composition. Synthetic Mn-tourmalines are of site deficiency in X-site ($0.53{\sim}0.68$) more than that of natural ones (approx. $0.2{\sim}0.3$) and show Mn cations occupying Y-site less than expected with initial experiments, leading to failure in synthesis of end-member tsilaisite. Rietveld structural refinements reveal that $R_{wp}$ ($R_{p}/R_{exp}$) is in the range of 13.35 and 18.62%, $R_{B}$ and S (CofF) are $4.85{\sim}6.25%$ (S-18: 8.57%), $1.31{\sim}1.59$ (S-18: 1.81), respectively. Unit cell parameters (space group R3m, z=3) are ${\alpha}=15.8994\;{\AA}$ and $c=7.1846\;{\AA}$ in average (S-18: ${\alpha}=15.9491\;{\AA},\;c=7.1773\;{\AA}$). Average bond lengths of and are $2.67{\sim}2.69\;{\AA}$ (S-18: $2.65\;{\AA}$) and $2.00{\sim}2.02\;{\AA}$ (S-18: $1.96\;{\AA}$), respectively. Ditrigonality (${\delta}$) are in the range of 0.022 and 0.031 (S-18: 0.061), indicating degrading symmetry with increase of Mn content.

• Economic and Environmental Geology
• /
• v.47 no.5
• /
• pp.479-488
• /
• 2014

Naturally occurring asbestos (NOA) from disturbance of rocks and soils has been overlooked as a source of exposure that could potentially have a detrimental impact on human health. But, few researches on mineralogical characteristics of NOA occurred in soils have been reported in Korea. Therefore, the objective of this study was to investigate the mineralogical characteristics of NOA occurred in soils at Daero-ri area, Seosan, Chungnam Province, Korea. Sedimentation method was used for particle size separation of the asbestos-containing soils. XRD and PLM analyses were used to characterize mineralogical characteristics and mineral assemblages in soils. SEM-EDS and TEM-EDS analyses were used to characterize mineral morphology and chemical composition. Particle size analyses of the asbestos-containing soils showed they were composed of 26-93% sand, 4-23% silt and 3-70% clay. Soil texture of the soils was mainly sand, sandy loam, sandy clay, and clay. PLM analyses of the soil showed that most of the soil contained asbestiform tremolite and actinolite. The average content of asbestos in the soil was 1.5 wt. %. Therefore, the soil can be classified into asbestos-contaminated soils based on U. S. Environmental Protection Agency classification (content of asbestos in contaminated soil > 1%). Morphologically different types of tremolite such as long fibrous, needle-like, fiber bundle, bladed and prismatic forms co-existed. Prismatic tremolite was dominant in sand fraction and asbestiform tremolite was dominant in silt fraction. This study indicates that the prismatic form of tremolite transform gradually into a fibrous form of tremolite due to soil weathering because tremolite asbestos was mainly existed in silt fraction rather than sand fraction.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.2
• /
• pp.131-136
• /
• 2001

Relative growth and composition of larval development stages in brood pouch of the melania snail, Semisulcospira libertina libertina were investigated based on monthly field samples for a year. Total number of specimens examined was 1,200. Size values (mean$\pm$S. D.) of shell height (SH), shell diameter (SD), total weight (TW), meat weight (MW) and shell weight (SW) were $15.96\pm3.41\;mm$, $7.82\pm1.38\;mm$, $0.55\pm0.31\;g$, $0.24\pm0.15\;g$ and $0.39\pm0.23\;g$, respectively, Water temperature (WT) of the sampling site varied from $1.3^{\circ}C\;to\;22.5^{\circ}C$. Relative growth equations among SH, SD, TW, MW and SW of S. libertina libertina specimens pooled were as follows: SD=0,3583SH+2.1648 $(R^2=0.8391)$, $TW=0.0005SH^{2.4853}\;(R^2=0.8391)$,$MW:\;0.0005SH^{2.849}\;(R^2= 0.8391)$ and $SW=0.0004SH^{2.3798}\;(R^2=0.7057)$. Female S. libertina libertina had larvae in its brood pouch throughout the year, Average number of larvae in the brood pouch varied from $91\pm33(July)$ to $396\pm174\;(November)$, decreasing in spring and increasing in autumn. In the monthly composition of larval stage in the brood pouch, trochophore, pre-veliger, veliger and juvenile showed maximum as $66.7\%$ in May, $70.7\%$ in November, $60.9\%$ in February and $13.9\%$ in January, respectively. Percent composition of the juveniles decreased in spring and autumn. In conclusion, S. libertina libertina is likely to have two main parturition periods, March to May and September and October.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.27-38
• /
• 2009

To investigate the feasibility of refuse derived fuels (RDFs) combined of sewage sludge and combustible wastes such as substitutive fuels instead of a stone coal, several different RDFs made with different mixtures of sewage sludge and combustible wastes were analyzed by various experiments. The combustion characteristics for the RDFs were investigated by analyzing fuel gases, and heating values were also measured by a bomb calorimeter. The fundamental properties such as moisture contents, ratios of combustible materials, amounts of ashes, heavy metals, ratios of each chemical elements and heating values were analyzed in accordance with mixing ratios of wt(%) for researching the characteristics of the RDFs. $RDF_{k-1}$ was made of mixing materials which were dried sewage sludge, food wastes and combustible wastes. $RDF_{k-2}$ was made of mixing materials which were peat-moss, tar and sewage sludge. Combustion experiments were carried out at the optimal conditions which were m=2 under air-fuel condition and $850^{\circ}C$. The retention times in the combustor were set at 5, 10 and 15minutes. 50 g of RDFs was put in the combustor for each experiments. The ranges for heating values of $RDF_{k-1}$ with different mixing ratios were from 6,900 kcal/kg to 8120 kcal/kg. The ranges for heating values of $RDF_{k-2}$ with different mixing ratios were from 4,014 kcal/kg to 8,050 kcal/kg. As a result of this study, the heating values, moisture contents, components of chemical elements and mixing ratios of the materials in RDFs had big effects on the efficiency of the combustion. In $RDF_{k-1}$, the higher amounts of combustible wastes in the mixtures, the higher heating values, concentrations of $C_xH_y$ and amounts of ashes were produced. In $RDF_{k-2}$, the higher tar amounts in the mixtures caused the higher heating values, amounts of ashes, concentrations of CO gas and CxHy.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.31 no.2
• /
• pp.257-262
• /
• 2002

Effects of dietary fatty acids and vitamin E on antioxidant system were studied in rat liver and serum. Sources of dietary fat (10 wt%) were safflower oil (SO) poor in $\omega$3 fatty acid and mixed oil (MO) with computer-adjusted fatty acid ratios (AA/DHA=1.4, $\omega$6/$\omega$3=6.3, P/M/S=1.0/l.5/1) with (ME) and without (MO) vitamin E (500 mg/kg diet). Rats were fed the three kinds of diet from 3~4 wks prior to the conception. At the age of 3 and 9 wks of the second generation rat, antioxidant vitamins and glutathione peroxidase (GSH-Px), superoxide dismutase (SOD) activities were measured in the liver and serum. The concentrations of $\beta$-carotene were lower in ME than in MO and SO in the liver at the age of 3 wks. It seemed that vitamin E has an inhibitory action on the uptake of $\beta$-carotene or acts as a preferred antioxidant to $\beta$-carotene. The concentrations of lycopene were lower in SO than in MO in the liver at the age of 3 wks. The concentrations of cryptoxanthin showed no significant changes within groups. The activities of GSH-Px tended to increase in ME compared to MO and the ratios of SOD/GSH-Px tended to decrease in ME compared to MO in the liver at the age of 3 weeks. The activities of antioxidant enzyme at the age of 3 weeks and 9 weeks were similar. This suggested that the activity level of antioxidant enzymes reached to the adult level at the age of 3 weeks which is the end point of lactation period.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.3
• /
• pp.121-129
• /
• 2015

The platinum anode for the electrolytic reduction process is generally surrounded by a nonporous ceramic shroud with an open bottom to offer a path for $O_2$ gas produced on the anode surface and prevent the corrosion of the electrolytic reducer. However, the $O^{2-}$ ions generated from the cathode are transported only in a limited fashion through the open bottom of the anode shroud because the nonporous shroud hinders the transport of the $O^{2-}$ ions to the anode surface, which leads to a decrease in the current density and an increase in the operation time of the process. In the present study, we demonstrate the electrolytic reduction of 1 kg-uranium oxide ($UO_2$) using the porous shroud to investigate its long-term stability. The $UO_2$ with the size of 1~4mm and the density of $10.30{\sim}10.41g/cm^3$ was used for the cathode. The platinum and 5-layer STS mesh were used for the anode and its shroud, respectively. After the termination of the electrolytic reduction run in 1.5 wt.% $Li_2O-LiCl$ molten salt, it was revealed that the U metal was successfully converted from the $UO_2$ and the anode and its shroud were used without any significant damage.