• Journal of the Korean Ceramic Society
• /
• v.32 no.12
• /
• pp.1369-1376
• /
• 1995

The WO3 thin-film NOx sensor which is of practical use and includes the heater and the temperature sensor was fabricated. The WO3 thin films as a gas-sensing layer was deposited at ambient temperature in a high-vacuum resistance heated evaporator. The highest sensitivity of the WO3 thin-film sensor to NOx was obtained under the condition of the annealing temperature of 50$0^{\circ}C$ and the operating temperature of 30$0^{\circ}C$. The gas sensing characteristics of this sensor was excellent, i.e. high sensitivity (Rgas/Rair in 3 ppm NO2=53) and fast response time (4 seconds).

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.118-124
• /
• 2001

When particles are dissolved in solution, they have different zeta-potentials depending on pH. Zeta-potential has an influence on particle separation, which can control particle size. And the size of $WO_3$ particle affects the sensitivity of $WO_3$ sensor for detecting NO gas. Therefore we study influence of pH on NO-sensing $WO_3$ gas sensor fabricated by Sol-Coprecipitation method. As pH increases from 2 to 7, dynamic mobility of $WO_3$ precursor was increased. When pH was 7, it showed the largest distribution separation. It means when pH is 7, we can make $WO_3$ powder which has smaller particle size. And it is confirmed by particle size analysis of $WO_3$ powder, X-ray diffration result of $WO_3$ sensing layer and surface morphology. It also affect NO sensing characteristics of $WO_3$ gas sensor. The sensing film synthesized at pH 7 showed the largest sensitivity.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.237-243
• /
• 1999

스크린 프린팅법을 이용하여 NOX 감지용 WO3 후막형 가스센서를 제조하였다. 본 실험에서는 감지막의 소성 온도에따른 감도변화 및 Ru을 첨가함으로써 감도의 증진을 중점적으로 조사하였다. 또한 NO2 50 ppm하에서 CO, H2, CH4 그리고 i-C4H10등의 가스에 대하여 cross sensitivity를 조사하였다. WO3 가스센서는 소성온도 50$0^{\circ}C$, 작동온도 30$0^{\circ}C$에서 최대감도를 얻었다. 순수한 WO3에 Ru(0.004 wt%)을 첨가시 NO2 및 NO 가스에 대한 감도가 크게 증진되었다. 그러나 순수한 WO3 센서는 Ru(0.004 wt%)이 첨가된 WO3 센서보다 더 우수한 cross sensitivity를 보였다.

• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.39-46
• /
• 1996

The Pd or Pt-doped $WO_{3}$ thin-film NOx sensor was fabricated. The $WO_{3}$-based thin films as a gas-sensing layer were deposited at ambient temperature in a high-vacuum resistance heated evaporator and annealed at $500^{\circ}C$. The gas sensitivity ($R_{gas}/R_{air}$) to 5 ppm $NO_{2}$ measured at the operating temperature of $300^{\circ}C$ was 50 (highest sensitivity) for the 0.5 wt.% $Pt-WO_{3}$ sensor.

• Journal of Powder Materials
• /
• v.26 no.1
• /
• pp.28-33
• /
• 2019

The gas sensor is essential to monitoring dangerous gases in our environment. Metal oxide (MO) gas sensors are primarily utilized for flammable, toxic and organic gases and $O_3$ because of their high sensitivity, high response and high stability. Tungsten oxides ($WO_3$) have versatile applications, particularly for gas sensor applications because of the wide bandgap and stability of $WO_3$. Nanosize $WO_3$ are synthesized using the hydrothermal method. As-prepared $WO_3$ nanopowders are in the form of nanorods and nanorulers. The crystal structure is hexagonal tungsten bronze ($MxWO_3$, x =< 0.33), characterized as a tunnel structure that accommodates alkali ions and the phase stabilizer. A gas detection test reveals that $WO_3$ can detect acetone, butanol, ethanol, and gasoline. This is the first study to report this capability of $WO_3$.

• Journal of Sensor Science and Technology
• /
• v.15 no.2
• /
• pp.120-126
• /
• 2006

Physicochemical and electrical properties for hydrogen gas sensors based on Pd-deposited $WO_3$ thin films were investigated as a function of Pd thickness, annealing temperature, and operating temperature. $WO_3$ thin films were deposited on an insulating material by thermal evaporator. XRD, FE-SEM, AFM, and XPS were used to evaluate the crystal structure, microstructure, surface roughness, and chemical property, respectively. The deposited films were grown $WO_3$ polycrystalline with rhombohedral structure after annealing at $500^{\circ}C$. The addition effect of Pd is not the crystallinity but the suppression of grain growth of $WO_3$. Pd was scattered an isolated small spherical grain on $WO_3$ thin film after annealing at $500^{\circ}C$ and it was agglomerated as an irregular large grain or diffused into $WO_3$ after annealing at $600^{\circ}C$. 2 nm Pd-deposited $WO_3$ thin films operated at $250^{\circ}C$ showed good response and recovery property.

• Journal of Sensor Science and Technology
• /
• v.23 no.5
• /
• pp.291-294
• /
• 2014

In this study, a chemiresistive sensor based on one-dimensional $WO_3$ nanostructures is presented for application in non-invasive medical diagnostics. $WO_3$ nanostructures were used as an active gas sensing layer and were deposited onto a $SiO_2/Si$substrate using Pt interdigitated electrodes (IDEs). The IDE spacing was $5{\mu}m$ and deposition was performed using RF sputter with glancing angle deposition mode. Pt IDEs fabricated by photolithography and dry etching. In comparison with thin film sensor, sensing performance of nanostructure sensor showed an enhanced response of more than 20 times when exposed to 50 ppm acetone at $400^{\circ}C$. Such a remarkable faster response can pave the way for a new generation of exhaled breath analyzers based on chemiresistive sensors which are less expensive, more reliable, and less complicated to be manufactured. Moreover, presented sensor technology has the potential of being used as a personalized medical diagnostics tool in the near future.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.193-198
• /
• 2008

$WO_3$-doped $SnO_2$ thin films were prepared in a solution-deposition method and their gas-sensing characteristics were investigated. The doping of $WO_3$ to $SnO_2$ increased the response ($R_a/R_g,\;R_a$: resistance in air, $R_g$: resistance in gas) to $H_2$ substantially. Moreover, the $R_a/R_g$ value of 10 ppm CO increased to 5.65, whereas that of $NO_2$ did not change by a significant amount. The enhanced response to $H_2$ and the selective detection of CO in the presence of $NO_2$ were explained in relation to the change in the surface reaction by the addition of $WO_3$. The $WO_3$-doped $SnO_2$ sensor can be used with the application of a $H_2$ sensor for vehicles that utilize fuel cells and as an air quality sensor to detect CO-containing exhaust gases emitted from gasoline engines.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.299-302
• /
• 2011

[ $WO_3$ ]powders were ball-milled with an alumina ball for 0-72 hours. $In_2O_3$ doped $WO_3$ was prepared by soaking ball-milled $WO_3$ in an $InCl_3$ solution. The mixed powder was annealed at $700^{\circ}C$ for 30 min in an air atmosphere. A paste for screen-printing the thick film was prepared by mixing the $WO_3$:In2O3 powders with ${\alpha}$-terpinol and glycerol. $In_2O_3$ doped $WO_3$ thick films were fabricated into a gas sensor by a screen-printing method on alumina substrates. The structural properties of the $WO_3$:$InO_3$ thick films were a monoclinic phase with a (002) dominant orientation. The particle size of the $WO_3$:$InO_3$ decreased with the ball-milling time. The sensing characteristics of the $In_2O_3$ doped $WO_3$ were investigated by measuring the electrical resistance of each sensor in the test-box. The highest sensitivity to 5 ppm $CH_4$ gas and 5 ppm $CH_3CH_2CH_3$ gas was observed in the ball-milled $WO_3$:$InO_3$ gas sensors at 48 hours. The response time of $WO_3$:$In_2O_3$ gas sensors was 7 seconds and recovery time was 9 seconds for the methane gas.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.304-308
• /
• 2000

WO$_3$/SnO$_2$ceramics has been suggested as an effective sensing material for monitoring offensive odor or pollutant gases. This work was focussed on improving long-term stability, which has been a principal problem generally taking place in SnO$_2$semiconductor gas sensor. Miniaturized thick film gas sensors were fabricated by screen printing technique. Two types of sensor materials, W doped SnO$_2$and WO$_3$mixed SnO$_2$, were comparatively investigated on those long-term stability and sensitivites to several gases. Small amount of W doping(0.1 mol%) into SnO$_2$largely improved the long-term stability. The W(0.1 mol%) doped SnO$_2$gas sensor had higher sensitivities to both acetone and alcohol compared with WO$_3$(5 wt%) mixed SnO$_2$gas sensor. On the contrary, WO$_3$(5 wt%) mixed SnO$_2$gas sensor showed more superior sensitivity to cigarette smoke due to larger W content.