Proceedings of the Korea Water Resources Association Conference
/
2009.05a
/
pp.271-275
/
2009
본 연구에서는 상수관로의 잔존수명을 통계적 기법 중 하나인 비례위험모형(PHM)에 적용하여 평가하였다. 비례위험모형을 구축하기 위한 개별관로의 생존시간은 관로의 파손율이 한계파손율에 도달하는 시간으로 정의하였다. 즉, Park and Loganathan(2002)에서 제시한 GPBM을 적용하여 시간에 따른 개별관로의 파손율을 추정하고 추정된 파손율과 한계파손율의 상등관계를 통해 생존시간을 산정하였다. 또한, 본 연구대상관로에 대한 GPBM을 구축함에 있어, 매설시점에서 누적파손횟수를 0으로 한 파손기록을 입력자료에 추가하는 방법과 가중계수(WF)의 범위를 수정함으로써 기존의 GPBM을 보완하였다. 이로써 파손사건이 최소 1회 이상 기록된 강관 및 주철관에 대한 비례위험모형을 구축하였다. 이와 같이 수정된 방법론은 관로 파손사건 등의 자료의 축적이 미비한 국내 여건에서 비례위험모형 및 GPBM과 같은 통계적 모형을 구축할 때 유용할 것으로 사료된다. 본 연구대상관로의 비례위험모형에 포함된 유의한 공변수는 관종과 관경 그리고 길이이며 관종은 비례성 가정을 위배하여 시간종속형 변수로 모형화되었다. 최종 채택된 PHM모형을 통해 생존함수를 추정하였으며 추정된 생존함수를 이용하여 개별관로의 잔존수명 및 경제적 수명 그리고 각 수명에 대한 95% 신뢰구간을 산정하였다. 또한 개별관로의 경제적 수명에 영향을 미치는 공변수의 위험비율도 분석하였다. 분석결과 강관의 평균 경제적 수명은 약 25.1년이고 주철관은 약 21년으로 산정되었다. 또한 관종에 따른 경제적 수명에 도달할 상대적인 위험률은 전반적으로 주철관이 높으나 20년 이상 매설된 관로에서는 강관의 위험률이 높을 것으로 분석되었다. 관경과 길이는 크기에 비례하여 상대적 위험률도 증가하였다.
Kim, Mun-Sung;Park, Hong-Shik;Jung, Kwang-Hyo;Chun, Ho-Hwan
International Journal of Naval Architecture and Ocean Engineering
/
v.8
no.5
/
pp.487-495
/
2016
In the offshore project such as semi-submersible FPU and FPSO, the free fall type life boat called TEMPSC (Totally Enclosed Motor Propelled Survival Craft) has been installed for the use of an emergency evacuation of POB (People on Board) from the topside platform. For the design of life boat arrangement for semi-submersible FPU in the initial design stage, the drop height and launch angle are required fulfill with the limitation of classification society rule and Company requirement, including type of approval as applicable when intact and damage condition of the platform. In this paper, we have been performed the numerical studies to find proper arrangement for the life boats consider drop height in various environmental conditions such as wave, wind and current. In the calculations, the contributions from static and low frequency (LF) motions are considered from the hydrodynamic and mooring analysis as well as damage angle from the intact and damage stability analysis. Also, Air-gap calculation at the life boat positions has been carried out to check the effect on the life boat arrangement. The air-gap assessment is based on the extreme air-gap method includes the effect of 1st order wave frequency (WF) motions, 2nd order low frequency roll/pitch motion, static trim/heel and set down.
Kim, Sea-Hyun;Jang, Yong-Seok;Chung, Hun-Gwan;Choi, Myoung-Sub;Kim, Sun-Chang
Plant Resources
/
v.6
no.2
/
pp.120-128
/
2003
The objectives of this study, an analysis of the variation for leaf and fruit characteristics among the selected ten populations of Sorbus commixta Hedl. could be used for the conservation of gene resources and could provide information to superior trees selection. The results obtained from this study can be summarized as follows; Approximately, the Mt. Sungin population at Ulleung island showed larger values in overall characteristics and populations. On the other hand, Mt. Halla population at Jeju island showed the smaller values of the overall characteristics and populations. ANOV A tests showed that there were statistically significant differences in all leaf characteristics among the populations as well as individual trees within populations. But, for fruit characteristics, differences were statistically significant only among the populations. Cluster analysis using single linkage method based on leaf and fruit characteristics showed that ten selected populations of S. commixta in Korea could be clustered into three groups. Group I is Mt. Sungin at Ulleung island, Group II is Mt. Halla at Jeju island, and Group III comprises Osan, Mt. Kaji, Mt. Duckyoo, Mt. Balwang, Mt. Sobaek, Mt. O-dae, Mt. Jiri, and Mt. Taebaek. The selection level based on major agronomic traits, which are the Number of Fruit per Fruiting Lateral(NFL) over 50, and Fruit Length(FL) and Width(FW) over 10 mm, and Weight of 100 Fruit(WFI00) over 66 g, was applied on 100 sample trees, and five trees were selected. The selection effects from selected trees in NFL, FL, FW, and WF100 were evaluated as 132%, 151 %, 142%, and 264% compared to the mean of those 100 sample trees, respectively. Especially, Ulleung 2 showed excellent values that NFL and WFI00 were 95, and 69 g, respectively, suggesting a promising new cultivar for larger fruit and high productivity.
Proceedings of the Korea Concrete Institute Conference
/
2008.04a
/
pp.105-108
/
2008
Although the research of high strength materials is in process briskly in the inside and outside of the country, in south korea, the research of high strength materials is insufficiency. Generally shear resistance of RC beam is influenced dominantly by amount of shear-reinforcing bars($p_w$) and yied strength($f_{wy}$). Therefore, I come to the conclusion that if use shear reinforced bar with shear reinforced bar, it leads to decrease of the quantity of shear reinforced bar and effects on the security of shear-restraint force of member. This study experimented with not only the mixture of high strength-reinforced bar and U-shaped reinforcement normal strength -reinforced bar devises efficient improvement, but also it incites improvement of bond capacity and carries out an experimental study for improvement of member resisting force, finally it evaluates bond capacity quantitatively on the lines of main reinforcement the restraint method.
This paper proposes a novel strategy for attenuating the output power fluctuation of the wind farm (WF) in a range of tens of seconds delivered to the grid, where the kinetic energy caused by the large inertia of the wind turbine systems is utilized. A control scheme of the two-level structure is applied to control the wind farm, which consists of a supervisory control of the wind farm and individual wind turbine controls. The supervisory control generates the output power reference of the wind farm, which is filtered out from the available power extracted from the wind by a low-pass filter (LPF). A lead-lag compensator is used for compensating for the phase delay of the output power reference compared with the available power. By this control strategy, when the reference power is lower than the maximum available power, some of individual wind turbines are operated in the storing mode of the kinetic energy by increasing the turbine speeds. Then, these individual wind turbines release the kinetic power by reducing the turbine speed, when the power command is higher than the available power. In addition, the pitch angle control systems of the wind turbines are also employed to limit the turbine speed not higher than the limitation value during the storing mode of kinetic energy. For coordinating the de-rated operation of the WT and the storing or releasing modes of the kinetic energy, the output power fluctuations are reduced by about 20%. The PSCAD/EMTDC simulations have been carried out for a 10-MW wind farm equipped with the permanent-magnet synchronous generator (PMSG) to verify the validity of the proposed method.
The objective of this study is to evaluate the lateral earth pressure and the stability of small scale retaining wall with waste foundry sand(WFS) mixtures as a controlled low strength materials (CLSM). Three different types of WFS, like Green WFS, Hurane WFS and Coated WFS, were used in this study, and fly ash of Class F type was adopted. To evaluate the lateral earth pressure and the stability of retaining wall, two different samll scale retaining wall tests, which are called an artificially controlled strain method and a natural strain method, were carried out. In case of an artificially controlled strain method, the coefficient of lateral earth pressure, just after backfilling of WF mixtures, was around 0.8 to 1.0, and most of earth pressure was dissipated within 12 hours. In case of a natural strain method, two steps of stage constructions were employed. The mixtures of Hurane WFS and Coated WFS showed fast decrease of earth pressure due to a relatively good drainage. Judging from the sta bility of retaining wall for overturning and sliding, two steps of stage construction for 2 days were enough to finish the backfill of 6-m height of retaining wall. Also, considering the curling effect of WFS mixtures, the stability of retaining wall increased as curling time increased.
Journal of the Korea Academia-Industrial cooperation Society
/
v.13
no.2
/
pp.562-574
/
2012
Simulation validation techniques which have been employed in most studies are statistical analysis, which validate a model with mean or variance of throughput and resource utilization as an evaluation object. However, these methods have not been able to ensure the reliability of individual elements of the model well. To overcome the problem, the weighted F-measure method was proposed, but this technique also had some limitations. First, it is difficult to apply the technique to complex system environment with numerous values of interarrival time because it assigns a class to an individual value of interarrival time. In addition, due to unbounded weights, the value of weighted F-measure has no lower bound, so it is difficult to determine its threshold. Therefore, this paper propose weighted F-measure technique with cluster analysis to solve these problems. The classes for the technique are defined by each cluster, which reduces considerable number of classes and enables to apply the technique to various systems. Moreover, we improved the validation technique in the way of assigning minimum bounded weights without any lack of objectivity.
In an attempt to make dried noodles with composite flours utilizing rice and wheat flours, noodle-making characteristics were improved by the addition of popped rice and wheat flours to rice flour. Their quality was studied in terms of physical properties, noodle-making characteristics, cooking quality test and sensory evaluation. Dried noodle of the composite flour was produced by the conventional method. The results are summerized as follows; 1. In comparing the composite flours, the rice flour containing 30% popped rice flour had a lower maximum viscosity than that with 40% popped rice flour by method of amylograph. The composite flour(20% rice+30% popped rice+50% wheat flour) with added 2% xanthan gum showed the viscosity characteristics which was similar to that of wheat flour. 2. Addition of $1.5{\sim}2.0%$ xanthan gum and $40{\sim}50%$ wheat flour to rice and popped rice flour mixture helped to improve the noodle making properties and the cooking quality, and the noodle making properties and the cooking quality of the mixed flour were almost the same as those of wheat flour alone. 3. The composite flour (rice+popped rice+wheat flour) with xanthan gum showed a higher score in sensory evaluation than that without xanthan gum. The general acceptability scores obtained with the noodle products made of the composite flours with 30% popped rice flour was not significantly different from that of noodle products made of wheat flour alone. However, the noodle products made of the composite flours showed rather higher scores in odor and palatability than the products made of wheat flour alone.
Proceedings of the Computational Structural Engineering Institute Conference
/
1992.10a
/
pp.3-3
/
1992
타이어 Curing공정은 공기압 타이어의 제조시 상당히 정교한 단계를 거쳐서 이루어지며, 이는 타이어 설계에 큰 영향을 줄 뿐만아니라, 타이어의 성능에도 관건이 있다. 본 연구에서는 유한요소법을 이용하여 타이어의 molding 공정을 분석하였다. 유한요소해석 프로그램인 MARC가 Cured 타이어 내부의 Curing Bladder 팽창과정해석에 이용되었다. 비압축성 요소로 Curing Bladder를 모형화하였으며, MARC의 접촉문제해석기법(contact option)을 이용하여 Cured 타이어 내부와 Curing Bladder 외부의 접촉부위를 Simulation하였다. 본 연구의 주요 관심내용으로서는 Curing Bladder의 형상변화에 따른 Curing Bladder의 팽창거동해석과, Cured타이어와 Curing Bladder의 접촉부위에서 얻을 수 있는 접촉압력의 비교.검토이다. 타이어 Curing시 타이어와 Bladder의 Contact과정을 해석하여, 아래와 같은 결과를 도출하였다. Bladder의 형상은 Cylinderical 형상 보다는 Toroidal 형태가 접촉압 분포의 균일성 및 크기 측면에 서 우수한 것으로 판단된다. Curing Bladder의 증심선 부위 보다 이에서 약간 떨어진 부위에서 최대 접촉압력이 발생되며, 이는 타이어 내면의 굴곡현상과 깊은 관련이 있윰 것으로 사료된다. 타이어 Bead부의 Carcass 자연평형현상이 유지된 제품을 얻기위해서는, Side-Bead구간의 접촉압력 증가가 필요하며, 이를 위하여는 Bladder 형상이 Cylinderical 보다는 Toroidal 형태가 유리하고, Bead부의 Gage Down, 전체직경의 증가 및 높이의 증가가 유리한 것으로 판단된다. 본 연구 결과를 이용하여, 타이어 Curing과정에서 발생되는 불량제품의 원인파악 및 타이어 설계자가 원하는 제품생산의 불가능한 원인을 파악하는데 도움을 줄 것이다.를 C의 structure와 pointer를 기반으로 하게끔 변경시키고 이에 따르는 제반 변경 사항을 수정 보완하여 프로그램의 분석을 용이하게 하며 기능의 변경 및 추가가 수월하게 하였고 메모리를 동적으로 관리할 수 있게 하였다. 또한 기존의 smpl에 디버깅용 함수 및 설비(facility) 제어용 함수를 추가하여 시뮬레이션 프로그램 작성을 용이하게 하였다. 예를 들면 who_server(), who_queue(), pop_Q(), push_Q(), pop_server(), push_server(), we(), wf(), printfct() 같은 함수들이다. 또한 동시에 발생되는 사건들의 순서를 조종하기 위해, 동시에 발생할 수 있는 각각의 사건에 우선순위를 두어 이 우선 순위에 의하여 사건 리스트(event list)에서 자동적으로 사건들의 순서가 결정되도록 확장하였으며, 설비 제어방식에 있어서도 FIFO, LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스템에 대한 시뮬레이션 구현과 시스템 분석의 예를 보인다._3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과 0.05 - 0.10 mm/hr 의 범위로서 이로 인한 강우손실량은 큰 의미가 없음을 알았다.재발이 나타난 3례의 환자를 제외한 9례 (75%)에서는 현재까지 재발소견을 보이지 않고 있다. 이러한 결과는 다른 보고자들과 유사한 결과를 보이고 있지만 아직까지 증례가 많지 않기 때문에 생존율을 얻
Background: Cytokine-mediated ex vivo expansion has been proposed as a means of increasing the number of cord blood (CB) hematopoietic stem cells for transplantation. As well as stem cell number, stromal cells are necessary for functional maturation of hematopoiesis. The purpose of this study was to analyze the development of stromal cells during ex vivo expansion of CB $CD34^+$ cells. Methods : $CD34^+$ cells were purified from CB by magnetic bead selection. The levels of of interleukin-3, interleukin-$1{\beta}$, interleukin-6, granulocyte macrophagecolony stimulating factor and tumor necrosis factor-${\alpha}$ were measured in culture supernatants on 0, 1, 2, and 3 weeks, using ELISA techniques. CB $CD34^+$ cells were expanded in Iscoves modified Dulbeccos medium in the presence of several cytokines. The expression of E-selectin, vascular cell adhesion molecule-1, intercellular adhesion molecule-1, platelet/endothelial cell adhesion molecule-1, von Willebrand factor, vimentin, and CD14 in newly developed stromal cells was examined by immunocytochemical method. Relevant extracellular matrix (ECM) proteins and proper cytokines were also assayed for the most suitable condition for expansion of stromal cells. Results: Several cytokines were found to have been produced by CB $CD34^+$ cells as well as bone marrow-derived $CD34^+$ cells. During ex vivo expansion of CB $CD34^+$ cells, stromal cells appeared in the culture by day 4 and expanded over the following 7-10 days before being confluent by day 2 1. These cells expressed surface markers characteristic of cells of endothelial lineage. Furthermore, these stroaml cells also expanded effectively when treated with thrombopoietin+flt-3 ligand+stem cell factor+leukemia inhibitory factor or 0.1% poly-L-lysine-coated wells. Conclusion: Stromal cells were developed during ex vivo expansion of CB $CD34^+$ cells and that this development could be enhanced further by treating the stromal cells with cytokines or ECM.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.