• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.4 s.112
• /
• pp.32-37
• /
• 2005

To Increase the productivity of a paper machine, the maximization of the machine speed is a kind of simple way As the machine speed increases, more intense wet pressing is required to persist the outlet consistency of press part and reduce the water removal of dryer part. With more intense pressing, there are concerns that the quality of paper will be affected. This study was carried out to evaluate the influence of wet-pressing on internal structure of paper, The nip pressure at the first and third nip in triple nip press was controlled. Paper structures, strength properties and pore properties were evaluated. As a result, first nip pressure more strongly influenced the paper structural properties than third nip pressure in triple nip pressing condition. Because of the high water content and low wet-web strength of paper web in first nip, increasing the first nip pressure induced the incipient crushing of wet-web and then caused a potential of web break during the following coating or printing processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6445-6452
• /
• 2015

The surface of the cooling coil becomes dry, wet or partially wet depending on the operating condition. Thus, a proper design of the cooling coil should include a heat transfer analysis on dry, wet or partially wet surfaces. In this study, an elementary model, which analyzes the cooling on an elementaty basis, is proposed. Comparison of the predictions of the model with experimental data of the cooling coil revealed that heat transfer rates were predicted within 10.1%, airside pressure drop within 11.1% and sensible heat ratio within 5.7%. The model was used to investigate the effect of water circuitory on cooling coil performance.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.567-570
• /
• 2009

The present study conducted comparative evaluation of wet dry floor heating systems using geothermal heat pump. Circulation hot water from geothermal heat pump which is $10{\sim}15^{\circ}C$ lower than that from boiler was used. In order to access indoor temperature ($25^{\circ}C$) it took 74 minutes for dry type and 247 minutes for wet type. Average floor temperature was $23.89^{\circ}C$ for wet type and $32.66^{\circ}C$ for dry type. Energy saving rate gradually increased by 66% after 138 minutes. In the results, for floor heating system using low temperature circulation water, wet type was not enough to meet stable and comfortable radiant floor heating due to low floor temperature and access time to indoor set temperature. While dry type was practicable for stable floor heating due to fast rise of indoor set temperature and comfortable floor temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.427-430
• /
• 2005

Improving the productivity of steel cord is required due to the increase in demand for it, even though steel cord being used as a reinforcement of a tire has been produced at multi-pass wet wire drawing process over 1000m/min. To improve the productivity, if just increase drawing speed, it causes temperature rise, fracture arisen by embrittlement during drawing process. To increase drawing speed affecting productivity, the variation of wire temperature during multi-pass wet wire drawing process is investigated in this study. In result, the multi-pass wet wire drawing process is redesigned. The redesigned wet drawing process with 27 passes efficiently controls wire temperature during drawing process. It, therefore, enables drawing process to be possible at ultra high speed with 2000m/min. It becomes possible to improve the productivity of steel cord in this paper because the increase in drawing speed could be achieved.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.6
• /
• pp.675-684
• /
• 2000

A novel dry and wet deposition collector, which can overcome the several problems such as water evaporation cartridge cracks and high costs founded in the previous collector systems, has been constructed. ENVI-18 SPE adsorption cartridge has been used to measure atmospheric deposition of polycylic aromatic hydrocarbons (PAHs). A surrogate surface, consisted of water and methanol, was filled in the dry deposition funnel to simulate dry deposition onto water surface. A water supply system in order to compensat evaporation of the surrogate surface was used and it was consisted of a piston pump, a tubing pump, a overflow tube and a chamber system. A novel water vaporizing system to supply water onto the wet SPE cartridge system with a constant flow rate was developed. The novel water vaporizing system, consisted of a vacuum pump, a water supply reserviour and tube and a mini space heater, could prevent the PAHs adsorption cartridge cracks occurred in the previous collector and effectively adsorb PAHs. The novel dry and wet deposition collector showed a good adsorption, desorption, and recovery rates of PAHs. By reducing the number of pumps used and employing polypyopylene (PP) instead of teflon as a material of collection funnel, the total construction costs were much reduced as compared with the previous dry and wet deposition collectors.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.3
• /
• pp.191-208
• /
• 1998

Estimations of dry and wet depositions in Korea and the size distributions of yellow sand above Korea have been carried out using the Eulerian aerosol model with the simulated meteorological data from the SNU mesoscale meteorological model. The estimated particle size distribution in Korea shows a bimodal distribution with peak values at 0.6 pm and 7 pm and a minimum at 2 pm in the lower layer However, as higher up, the bimodal distribution becomes an unimodal distribution with a peak value at 4∼5mm. Among the total amount of yellow sand deflated in the source regions , the dry and wet deposition fluxes were about 92%, and about 1.3∼0.5%, repectively, and the rest(5∼6%) is suspended in the air, Most of dust lifted in the air during the clear weather is deposited in the vicinity of the source regions by dry deposition and the rest undergoes the long -range transport with a gradual removal by the wet deposition processes. Over Korean peninsula, the total amount of yellow sand suspended in the air was about 6∼8% of the emissions in the source region and the dry and wet deposition fluxes were about 0.005∼0.7% and 0.003∼0.051% of the total emitted amount, repectively. It is estimated that 2.7∼8.9 mesa-tons of yellow sand is transported annually over the Korean peninsula with the annual mean dry deposition of 2.1∼490 kilo-tons and the annual mean wet deposition of 1.5∼65 kilo-tons.

• Food Science of Animal Resources
• /
• v.40 no.5
• /
• pp.844-851
• /
• 2020

The objective of this study was to compare effects of two different aging methods on physical, chemical, and microbial traits of pork loin: Dry and wet-aged meat was hung in the cooler at 8±1℃ and 85±2.1% humidity for 14 days, while wet-aged meat was immersed in a 3.5% salt solution of brine in vacuum pouches. On day 7, pH and moisture content were higher in dry-aged loins than in wet-aged, while drip loss and total plate counts (p<0.05) were lower on day 14. As aging continued, the pH and drip loss of dry-aged loins decreased, while their total plate counts and water holding capacity (WHC) increased (p<0.05). After 7 and 14 days of aging, redness in dry-aged loins was higher than that in wet -aged muscles (p<0.05). On day 14 of aging, hardness, chewiness, and adhesiveness were lower in dry-aged pork loin as compared to those in wet-aged samples (p<0.05). Consequently, the results suggested that dry and wet aging methods differently affects meat quality traits of pork loin.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.42 no.3
• /
• pp.5-17
• /
• 2000

The story of route of wet-rice diffusion to Korean peninsular is so far known only piecemeal. It is however commonly agreed that wet-rice technology may have spread the western coastal area in Korea from the lower and middle reaches of the yangzi river in China and to the Shandong peninsular and Bohai Bay region and was then transmitted overland to the area in Korea. Recently excavated three prehistoric paddy fields in Korea provide crucial evidence that helps to solve many of the important problems associated with technological diffusion. Research on the paddy field system and irrigation technology of prehistoric wet-rice has been so far especially productive in Japanese archaeology. Judging from the fact that the Yayoi wet-rice agricultural technology in Japan was transmitted by the Korean Strait from the southern part of Korea it is assumed that people in both regions may have practiced the same technology in prehistoric time. This paper examines three prehistoric paddy fields system(the Majon-ri site the Kwanchang-ri site and the Mujon-dong site) in relation to those of japanese data. The conclusions are as follows ; First early wet-rice agriculture in korea was limited by the level of technology and the size of labour. Secondly the location of field itself was restricted to the lower land and valley bottom area. Thirdly the layout of channel and field network is not very much different from the modern paddy field system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.926-929
• /
• 2007

A significant progress has been made in the characterization of zinc oxide (ZnO) semiconductor as a new semiconductor layer instead of amorphous Si semiconductor used in thin film transistor due to its high electron mobility at low deposition temperature which is quite suitable for flexible display and OLED devices. The wet pattering of ZnO is another important issue with regard to mass production of ZnO thin film transistor device. However, the wet behavior of ZnO thin film in aqueous wet etching solutions conventionally used un TFT industry has not been reported yet, in this work, wet corrosion behavior of RF magnetron sputtered ZnO thin film in various wet solutions such as phosphoric and nitric acid solutions was studied using by electrochemical analysis. The effects of deposition parameters such as RF power and oxygen partial pressure on corrosion rate are also examined.

• Environmental Engineering Research
• /
• v.10 no.6
• /
• pp.306-315
• /
• 2005

Total gas phase mercury (TGM) concentrations and event wet-only precipitation for Hg were collected for nine months (from April, 2002 to Dec., 2002) at Sterling, NY on the shoreline of Lake Ontario. TGM concentrations measured in this study ($3.02{\pm}2.14\;ng/m^3$) were in somewhat high range compared to other background sites. Using simplified quantitative transport bias analysis (SQTBA) possible sources affecting high Hg concentration in Sterling was identified, and they are coal-fired power plants located in southern NY and Pennsylvania. Wet deposition measured at Mercury Deposition Network (MDN) sites including Pt. Petre and Egbert, ON were compared with data obtained at the Sterling to estimate the total mercury wet deposition flux to Lake Ontario. The wet deposition flux was calculated to be the highest at the Sterling site ($7.94\;{\mu}g/m^2$ from April, 2002 to Dec. 2002) and the lowest at the Egbert ($3.92\;{\mu}g/m^2$), due to the both the difference in precipitation depth and Hg concentration in the precipitation. The deposition measured at the Sterling site is similar to Lake Michigan deposition of $6-14\;{\mu}g/m^2$ (converted for ninth months) measured for Lake Michigan Mass Balance Study (LMMBS).