• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.266-270
• /
• 1996

The microstructure evolution during sintering of a compact being composed of three layers of (WC-15%Co)/Fe powder mixture with different Fe contents has been observed. The Fe contents in the respective (WC-15%Co)/Fe layers were varied by 20%. 50%, and 90% in sequence by volume from a top layer to a bot- tom layer. The sintering temperatures and times were varied from 110$0^{\circ}C$ to 125$0^{\circ}C$ and from 1 h to 4 h, The compact layer was not densified below 120$0^{\circ}C$ in 4 h. Appropriate sintering temperature and time conditions for making a multi-layered hard metal compact were determined as 125$0^{\circ}C$ and 3 h, respectively.

• Journal of Powder Materials
• /
• v.3 no.2
• /
• pp.91-96
• /
• 1996

The effect of vacuum annealing on the oxidation behavior of milled WC-15%Co powder mixture has been studied. A cobalt component in the milled powder mixture was oxidized preferentially above 175$^{\circ}C$ in air. The specimens showed a steady increase in weight at 175$^{\circ}C$ but did constant weight followed by rapid increase in specimen weight at the beginning above 20$0^{\circ}C$. Oxidation of the milled powder mixture was significantly suppressed by vacuum annealing at 30$0^{\circ}C$ for 10 h. Suppression of oxidation by vacuum annealing and different oxidation behaviors of the milled powder mixture between 175$^{\circ}C$ and 20$0^{\circ}C$, were attributed to removal of strain energy stored in the cobalt powder during vacuum annealing or oxidation treatment above 20$0^{\circ}C$. The role of stored strain energy on oxidation of milled WC-15%Co powder mixture was proved by X-ray diffraction method and differential thermal analysis.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.66-71
• /
• 2008

Diamond-like-carbon (DLC) coatings could be good candidates as solid lubricants for cutting tools in dry machining of aluminum alloy. In this work, DLC thin films were produced as a friction reduction coating for WC-Co insert tip using the plasma immersion ion beam deposition (PIIED) technique. DLC coatings were also coated on $Al_2O_3$ specimens and high temperature wear tested up to $400^{\circ}C$ in dry air to observe the survivability of the DLC coating in simulated severe cutting conditions using a pin-on-disc tribotester with Hertzian contact stress of 1.3GPa. It showed reduced friction coefficients of minimum 0.02 up to $400^{\circ}C$. And cutting performance of DLC coated WC-Co insert tips to Al 6061 alloy were conducted in a high speed machining center. The main problems of built-up edge formation in aluminum machining are drastically reduced with improved surface roughness. The improvements were mainly related to the low friction coefficient of DLC to Al alloy and the anti-adhesion of Al alloy to WE due to the inertness of DLC.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.688-696
• /
• 1995

Cemented carbides, best known for their superior mechanical properties such as high strength, high hardness and high wear resistance, have a wide range of industrial applications including metal working tools, mining tools, and wear resistance components. The cobalt has been used as a binder in the WC-based hard composites due to its outstanding wetting and adhesion characteristics even though its expensiveness. Therefore many studies attempted to find a better substitute for cobalt as binder to decrease production costs. This investigation is a pre-step to study dynamic fracture characteristic evaluation of a WC-Co hardmetal were evaluated by using the instrumented Charpy impact testing procedures. It was found that the dynamic characteristics of used strain amplifier were very important experimental factors to extract valid dynamic fracturing data in WC-Co specimens. It was suggested by showing some experimental examples that when we wished to evaluate dynamic fracture toughness for cemented carbide composites by using the instrumented Charpy impact testing procedure, a careful attention must be given to obtain valid results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.594-598
• /
• 2015

The effects of Ni on the mechanical properties of WC-Xwt.%Ni-1.5wt.%Si-1.1wt.%$B_4C$ composite (X = 21.6, 23.6, 25.6 and 27.6 wt.%) were investigated in order to replace Co with Ni as the binder metal for hard materials based on WC-Co system. Using X-ray diffraction, optical microscopy, field-emission scanning electron microscopy results, the microstructure, pore distribution and grain size of the composites sintered at $1,150^{\circ}C$ were examined with different fraction (X = 21.6, 23.6, 25.6 and 27.6 wt.%) of binder metal Ni. The average WC grain size of the $WC-Ni-Si-B_4C$ composites was about $1{\mu}m$. The Rockwell hardness : A (HRA) and transverse rupture strength were about 88HRA and $110kgf/mm^2$, respectively. The obtained sample was bonded with SM45C at a temperature of $1,050^{\circ}C$. The thickness and mechanical properties of the bonded area were investigated with different dwell time at a bonding temperature of $1,050^{\circ}C$.

• Journal of Powder Materials
• /
• v.5 no.3
• /
• pp.178-183
• /
• 1998

Ultrafine WC-10wt.%Co cemented carbides powders were synthesized by direct carburization. W-Co composite powders and carbon black powders were mixed by wet ball milling and dried. The mixed powders were heated to 800 $^{\circ}C$ with heating rate of 8.2$^{\circ}C$/min and held for various times in flowing $H_2$. For carbon addition of 140%, the carburization was completed by heating at 80$0^{\circ}C$ for 4 hours. The carburization time decreased with increasing amount of carbon and carburization was completed by heating at 800 $^{\circ}C$ for 2 hours with carbon addition of 150%. WC-10 wt%Co cemented carbides powders fabricated by direct carburization have nanoscale WC($\/leqq$100 nm) size.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.279-285
• /
• 1998

The microstructures and mechanical properties of submicron WC-Co cemented carbides were investigated in relation to cobalt content. To inhibit the WC grain growth during sintering, VC was added as a inhibitor in each alloy with 3 mass% to the cobalt content. The WC-(5, 8, 10, 15, 20) mass% Co compacts were sintered at $1400^{\circ}C$ for 30 min in vacuum. Some of WC-(5, 8, 10) mass% Co sintered compacts were HIPed with 120 atm at 130$0^{\circ}C$ for 1 hr. The shrinkages of all HIPed alloys were increased without depending on the cobalt contents and the sintered densities of them. The relative densities of the alloys were increased with the cobalt content and HIPing. The less the cobalt content, the larger the WC grain. Many contiguities of WC grains were found in WC-5 mass% Co alloy. The sizes and numbers of pores in the alloys were decreased by HIPing. And also the strength and the hardness of each alloy were increased. The maximum hardness was about 18.95 GPa in the WC-5 mass% Co alloy HIPed and the maximum transverse-rupture strength (T.R.S.) 3.2 GPa in the WC-20 mass% Co alloy sintered.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1520-1530
• /
• 1997

Machining pressed compacts of ceramic and WC-Co materials can be the most cost effective way of forming the bodies prior to sintering when the required number of pieces is small. In this study, in order to clarify the machinability for turning, the $Si_3N_4$ and the WC-Co green compacts unsintered were machined under different cutting conditions with various tools. Absorbing chips by vacuum hose decreases tool wear. The tool wear becomes larger in the order of the ceramic, CBN and cemented carbide tools in machining the $Si_3N_4$ green compacts. In machining the WC-Co green compacts, the tool wear becomes larger in the order of the ceramic, cemented carbide and CBN tools. The land of cutting edge does not affect tool wear. When machining with cemented carbide tool, the tool wear i equal cutting length is nearly identical in spite of the increase of cutting spee, and the roughness of machined surface was the best in the cutting speed of 90 m/min. The tool wear decreases with the increase of rake angle and relief angle and with the decrease of nose radius. The machined surfaces become worse with the increase of feed rate and depth of cut, and with the decrease of rake angle and relief angle. The tool wear is not affected by the feed and depth of cut.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.04b
• /
• pp.8-8
• /
• 2002

서멧이란(Cermet) '세라믹 경질상과 금속 결합상의 복합체"를 의미하나 절삭 골구계에서는 좁은 의미의 "TiC 혹은 Ti(CN)을 바탕을 Ni,Co를 결합상으로 하는 초경재료"를 의미한다. 이런한 서멧은 전략 물질적 성격이 강한 Co,W로 구성된 WC-Co 초경 합금을 대체하기 위해 고안되었는ㄴ데 ㄴ놓은 경도와 고온에서의 화학적 안정성, 낮은 비중과 저렴한 원료 가격등이 장점이나 WC-Co에 비해 상대적으로 낮은 인성이 문제점으로 지적 되어왔다.TiC-Ni 서멧의 낮은 인성을 향상시키기 위해 Ti(CN) 고용체를 바탕으로 하고 제2ㅇ, 제3의 탄화물이나 질화물을 첨가하는 개발 연구가 과거 30여 년간 진행되어왔다. 그러나 많은 연구결과가 조성 개발 위주로 진행되어 왔고, 또 실험간의 불일치와 재현성 결여로 인해 보여진 여러 현상에 대한 보편적인 결론을 내리기 힘든 점이 있었다. 특히, 미세구조와 기ㅔ적 특성에 관한 통합적이고 조직적인 연구가 진행되지 못하였다. 이번 발표에서는 발표자 실험실에서 지난 8 년 간 행하여 온 실험 결과를 바탕으로 탄화물서멧에 나타나는 독특한 현상, 고용체 탄질화물의 열역학적 안정성, 서멧 재료의 유심구조, 표면 에너지 및 strain, 에너지가 미세 구조 형성에 미치는 영향, 그리고 표면층 형성 등 서멧 개발에 관한 중요 관심사에 대해 간단히 살펴보려고 한다.해 간단히 살펴보려고 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.99-99
• /
• 2013

나노결정질 다이아몬드(Nanocrystalline Diamond: NCD) 박막은 고경도와 낮은 마찰계수를 가지고 있어 초경합금이나 고속도강과 같은 절삭공구 위에 코팅하여 공구의 성능 향상을 도모하려는 노력이 있어 왔다. 그러나 NCD 박막의 잔류응력이 크고, 초경합금과 철계 금속에 NCD가 증착되지 않는다는 문제점이 있다. 따라서 잔류응력 완화와 다이아몬드 핵생성을 위하여 제3의 중간층 재료가 필요하다. 본 연구에서는 W과 Ti을 중간층으로 하여 초경합금(WC-Co)과 고속도강(SKH51)에 NCD 박막을 코팅하고 기계적 특성을 비교하였다. 초경합금 또는 고속도강기판 위에 W 또는 Ti 중간층을 DC magnetron sputter를 이용해 각 1 ${\mu}m$의 두께로 증착하고 그 위에 MPCVD (Microwave Plasma Chemical Vapor Deposition)를 이용해 NCD 박막을 2${\mu}m$의 두께로 코팅하였다. FESEM을 이용하여 표면과 단면의 형상을 관찰하였고, XRD와 Raman spectroscopy를 통해 NCD 박막의 결정성을 확인하였다. 그리고 tribology test를 실시하여 코팅된 박막의 내마모성을 비교하였으며, Rockwell C indentation test를 이용하여 밀착력을 비교하였다. 초경합금에 적용 시, W이 Ti보다 중간층으로서 더 우수한 것으로 나타났으며 이는 열팽창계수 차이에 의한 잔류응력의 차이에 의한 것으로 여겨진다. 중간층 두께에 따른 박막의 기계적 특성 변화를 알아보기 위해 W 중간층의 두께를 1, 2, 4 ${\mu}m$로 변화를 주었다. 중간층 두께가 2 ${\mu}m$ 이상일 때 박막의 밀착력이 증가되는 것으로 나타났다. 고속도강 위에 같은 방법으로 1 ${\mu}m$의 W 또는 Ti 중간층 위에 2 ${\mu}m$의 NCD 박막을 코팅한 시편들은 초경합금에 코팅한 것과 달리 두 시편 모두 낮은 밀착력을 나타내었다. 열팽창계수 차이에 의한 잔류응력을 완화하기 위해 고속도강에 W/Ti 복합박막을 중간층으로 Ti, W순으로 각각 1 ${\mu}m$ 두께로 증착 후 그 위에 NCD 박막을 2 ${\mu}m$ 두께로 코팅 한 후 특성을 비교하였다. Ti/W 복합 중간층 위에 코팅된 NCD 박막의 밀착력이 W 혹은 Ti 단일 중간층에 코팅된 박막에 비해 우수한 것으로 나타났다. 그러나 실제 공구에 적용하기에는 박막의 밀착력 개선이 요구되며 이를 위해서 더 연구가 필요하다.