• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.45.1-45
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.05a
• /
• pp.42-42
• /
• 1997

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.45-46
• /
• 2003

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1996.04a
• /
• pp.18-18
• /
• 1996

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1997.04a
• /
• pp.14-14
• /
• 1997

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.85-85
• /
• 2003

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.109-113
• /
• 2002

본 연구에서는 공침법에 의한 초미세분말을 이용하여 제조된 (NiCuZn)-ferrite와 건식법을 이용하여 제조된 (NiCuZn)-ferrite의 저온소결 특성 및 전자기적 특성을 상호 비교 분석하였다. 조성은 (N $i_{0.4-x}$C $u_{x}$Z $n_{0.6}$)$_{1+w}$(F $e_2$ $O_4$/)$_{1-w}$에서 x의 값을 0.2, w의 값은 0.03으로 고정하였고, 소결은 공침법으로 합성된 분말의 경우 초기열처리과정을 거쳐 최종적으로 90$0^{\circ}C$에서, 건식법의 경우 11$50^{\circ}C$의 온도에서 진행하였다. 그 결과, 공침법으로 제조된 (NiCuZn)-ferrite는 건식법으로 제조된 (NiCuZn)-ferrite보다 20$0^{\circ}C$이상 낮은 소결온도에서 높은 소결밀도 값을 가졌으며, 품질계수 등 칩 인덕터에서 중요한 요소인 전자기적 특성이 우수하게 나타났다. 또한, 공침법으로 합성된 페라이트는 분말의 초기열처리온도에 따라 최종소결 특성이 크게 변하였다. 그밖에 공침법과 건식법으로 합성한 (NiCuZn)-ferrite의 결정성, 미세구조들을 XRD, SEM, TEM을 이용하여 비교 고찰하였다.하였다.다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.297-303
• /
• 2003

Mn-Ni-Co type thin films were prepared at various conditions by a rf magnetron sputtering system. At the condition. or substrate temperature of $300^{\circ}C$ and $Ar/O_2$= 10/0, a cubic spinel phase was obtained. When oxygen was included in process gas, a cubic spinel phase was not formed even after the thermal annealing at $900^{\circ}C$. The thermistor thin film had no other elements except Mn, Ni and Co. The infrared reflection spectra of the thermistor thin films showed that the films had somewhat high reflectance for incoming infrared ray with some angle. The etch rate of the thermistor thin films was about 63nm/min at a condition of DI water : $HNO_3$: HCl = 60 : 30 : 10 vol%. The B constant and temperature coefficient of resistance of the thermistor thin films were 3500 K and -3.95 %/K, respectively. The voltage responsivity of the thermistor thin film infrared sensor was 108.5 V/W and its noise equivalent power and specific detectivity were $5.1\times 10^{-7}$ W/$Hz^{-1/2}$ and $0.2\times 10^6$cm $Hz^{1/2}$/W, respectively.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1995.11a
• /
• pp.25-25
• /
• 1995

Liquid phase sintering of 90W-6Ni-4Mn alloy has been investigated as functions of sintering atmosphere, heating rate, and reduction temperature. The present work accounts for the thermodynamic oxidatiodreduction reactions of constituent powders of W, Ni and Mn. By discounting these reactions, the previous investigations would obtain only the alloy with large pores and the lowered relative sintered density, by the liquid phase sintering under a dry hydrogen atmosphere. the sintering cycle consisted of a rapid heating to reduction temperatures under high purity nitrogen atmosphere, and holding for 4 hours and sintering at $1260^{\circ}C$ for 1 hour under a dry hydrogen gas. The relative density of the sintered alloy increased with increasing heating rate. As the reduction temperature increased, the relative density increased to the lm theotical density at the duction temture above $1150^{\circ}C$. The mimsturcatre of sintered alloys has been analysed by a scanning election microscope. The sintered density was compared with those obtained from the other investigators. It was found that the reduction $1150^{\circ}C$ results in the lowered densification of 90W-6Ni-4Mn alloy. This is caused by the fact that reducing reactions of W and Ni oxides contained in W an Ni powders concomitantly leads to oxidizing reaction of Mn powder the oxidized Mn is hardly reduced at sintering temperature and thereby remains large pores in the alloy. It is concluded that the W-Ni-Mn alloy with full density can be obtained by the precise control of atmosphere, heating rate, and sintering temperature.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1095-1097
• /
• 1995

We studied on Solide Oxide Fuel cells, have some advantages of higher power density and less cost for power-supply. Recently, Ni-YSZ materials are used as anode of SOFC. If its contents of Ni is higher then its electronic conductivity is higher. And If it has inverse tendency then its ionic conductivity become higher. So in this experiments, we investicated the optimum content of Ni, by testing expansion coefficient, impedance characteristics, overvoltage.