• 대기
• /
• 제20권3호
• /
• pp.367-377
• /
• 2010

Variation of tracer distribution during the vortex-breakup period in the Antarctic region was observed by the data from the Improved Limb Atmospheric Spectrometer (ILAS) and ILAS-II. All four trace species including methane, nitrous oxide, ozone, and water vapor show similar patterns of vertical gradient in spite of different structures of zonal mean mixing ratio. Timings of vortex breakup on each level are estimated by two different methods, and they are compared with zonal standard deviations following the latitude circle of each trace species. Although the tracers have different chemical life times and sink/source, the zonal standard deviation patterns show remarkable similarities. The zonal standard deviation shown here to measure the zonal asymmetry of tracer distribution is believed to diagnose the timing of the Antarctic polar-vortex breakup reasonably well.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.69-76
• /
• 2002

The aim of this study is to provide fundamental informations that make it possible to use a cool stream and a hot stream simultaneously. We changed the pressure of compressed air that flows into a tube, the inner diameter of orifice that a cold stream exits, and the mass flow rate ratio. And in each case, we measured the temperature of a cold stream and a hot stream in each exit of a tube. Also we measured the axial and the radial temperature distribution in internal spare of a tube. From the study, fellowing conclusive remarks 7an be made. First, As the number of nozzles increase, separation point move into the hot exit. Second, When we use guide vane type nozzle, the axial temperature distribution constant over the 0.75 of air mass flow rate radio. Third, When we use Spiral type nozzle, axial and radial temperature distribution in the inner space is higher than another nozzle. Fourth, Axial and radial temperature distribution in the inner space vortex-tube is determined by separation point. And separation point is moved by changing of air mass flow rate ratio. At last, A heating apparatus is possible far vortex-tube to use.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.27-30
• /
• 2002

An experimental study is performed to investigate the characteristics of near wake behind a circular cylinder with serrated fins using the constant temperature anemometer and through flow visualization. Previous report(Boo at al., 2001) shows that there are three different modes in vortex shedding behavior. This paper is focused on the identification of the physical reasons why the difference is occured in vortex shedding. The through flow velocity crossing fins decreases as increasing fin height and decreasing fin pitch mainly due to the flow resistence. Vortex shedding is affected strongly by velocity distribution around fin tube, especially by the velocity gradient. The velocity distribution at X/d=0.0 has lower gradient with increasing freestream velocity and fin height and decreasing fin pitch. Those differences in velocity gradients generate different vortex shedding mechanism.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1979-1989
• /
• 1992

본 연구에서는 말굽와류에 대한 전반적인 사항을 고찰하는 한편, 실린더의 기 하학적 형상이 말굽와류에 미치는 영향을 정성적으로 고찰하는 데 있다. 그러므로 본 실험에서는 먼저 경계층이 형성되어 있는 평판에 원형 실린더를 설치하여, 말굽와 류에 의한 3차원 유동현상을 고찰하고, 또한 동일한 평판에 쐐기형상의 실린더를 설치 하여, 그 주위에서 발생하는 3차원 유동현상과 원형 실린더 주위에서 일어나는 3차원 유동현상과의 정성적인 비교를 통하여, 말굽와류에 의한 3차원 유동손실을 줄일 수 있 는 가능성을 제시하고자 한다.

• 대한조선학회논문집
• /
• 제30권3호
• /
• pp.62-74
• /
• 1993

균일한 정상유동을 하는 유체 안에 가로놓인 원주로부터 일어나는 vortex유출을 이산 vortex 방법을 써서 vortex cloud모형으로 simulation했다. 원주표면에서 생겨나는 와도를 매 시간 간격마다 미리 정해진 많은 갯수의 이산화된 초생 vortex로 나타낸 후 기 유출된 vortex들에 합류시켜 누적된 vortex들의 운동을 탐색함으로서 vortex 분포 상태의 진화를 알아낸다. vortex들의 이동은 cloud-in-cell 기법을 써서 추적 하였고 항력 계수와 양력 계수는 Sarpkaya의 식과 Lee의 식을 써서 계산하여 실험치와 비교하였다. 계산 인수 사이의 상호 연관 관계를 논고하였으며 부분적이나마 적정값 선정 원칙을 제시하였다.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.235-241
• /
• 2002

The process of energy separation in a low pressure vortex tube with air as a working medium is studied In detail. Experimental data of the temperature of the cold and hot air leaving the vortex tube are presented. The variation of the maximum wall temperature along the inner surface of the vortex tube and the temperature distribution in the vortex tube provides useful information about the location of the stagnation point of the flow field at the axis of the vortex tube. In this study Outer tube is used for the application of Diesel engine exhaust. The hot gas flow is fumed 180° and passes the outside of the vortex tube a second time heating it. From this geometric setup of a vortex tube the effects of energy separation and the prediction of the ignition of Diesel Soot is presented by experimental data.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2573-2578
• /
• 2007

In order to investigate the vortex body frame interaction around the side mirror of a passenger car, velocity vector fields in the wake, pressure distributions and boundary layer flows over both the mirror surface and the mirror housing, have been measured by several experimental tools. It was resulted that only within an half downstream distance of the mirror span there appears the recirculation zone, and also found that vortex trail towards to the driver side window between A and B pillars, making the acoustic noise and vibration. Wake vortex rolls up after this recirculating zone and makes the trail of the vortex center towards the driver side window, which was also confirmed by measurements of wake velocity vectors in the vertical sections of the trail and visualization over the side mirror surfaces as well. It was also observed that total pressure distribution over the mirror surface has the minimum peak near the lower tip region which can be considered as the origin of the vortex center. It can be concluded that the geometrical modification of the lower tip and the upper root area of the mirror housing is the key to control the wake vortex.

• International Journal of Aeronautical and Space Sciences
• /
• 제6권2호
• /
• pp.84-96
• /
• 2005

Helical tip vortex is known as stable vortex structure, however the specific frequency component of far wake perturbation induces the vortex pairing in hover and axial flight. It is expected that the tip vortex pairing phenomena may happen in transition flight and very low advance ratio flight so that inflow may be most nonuniform in the low advance ratio flight. The objectives of this paper are that a tip-vortex instability during the transition from hover into very low advance ratio forward flight is numerically predicted to understand a physics by using a time-marching free-wake method. To achieve the objectives, numerical method is firstly validated in typical axial and forward flights cases. Present scheme with trim routine can predict airloads and inflow distribution of forward flight with good accuracy. Then, the transition flight condition is calculated. The rotor used in this wake calculation is a small-scale AH-1G model. By using a tip-vortex trajectory tracking method, the tip-vortex pairing process are clearly observed in transient flight($\mu$=0.03) and disappears at a slightly higher advance ratio($\mu$=0.05). According to the steady flight simulation at $\mu$=0.03, it is confirmed the tip-vortex pairing process is continued in the rear part of rotor disk and not occurs in the front part. Time averaged inflow in this case is predicted as smooth distribution.

• Journal of Hydrospace Technology
• /
• 제1권1호
• /
• pp.1-13
• /
• 1995

Vortex shedding from a circular cylinder is simulated by means of the discrete vortex method. The shear layer emanating from the separation point is approximated as a sheet vortex which is in turn represented by a sequence of discrete vortices. The strength of these vortices is calculated from the vorticity shedding rate and introduced at a small distance off the side ($\Theta=\pm\pi/2$) of the cylinder surface in regular time step. Sheet vortex cutting, rediscretization and replacement of vortex by vortex segment are put to use to enhance stability of the sheet vortex evolution. The simulated vortex distribution pattern very well reproduces structure like the Karman vortex street. However, as for the force coefficients, the qualitative properties are correctly predicted but some more improvements are needed for the quantitative accuracy.

• 대한기계학회논문집B
• /
• 제26권1호
• /
• pp.82-93
• /
• 2002

The effects of the interaction between the flow and temperature field and a boundary layer due to a variety of the height of a vortex generator are experimentally investigated. The test facility consists of a boundary-layer wind tunnel with the vortex generator protruding from the bottom surface. In order to control the strength of the longitudinal vortices, the angle of attack and the spacing distance of the vortex generator are 20 degree and 40 mm, respectively. The height of the vortex generator (H) is 15 mm, 20 mm and 30 mm and the cord length of it is 50 mm. Three-component mean velocity measurements are made using a 5-hole probe system and the surface temperature distribution is measured by the hue capturing method using thermochromatic liquid crystals. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the downwash region where the strong downflow and the lateral outflow of the boundary layer fluid occur and thickened in the upwash re,3ion where the longitudinal vortex sweeps low momentum fluid away from the bottom surface. In case that the height of the vortex generator increases, the averaged circulation and the maximum vorticity of the vortex pair decrease. The contours of the non-dimensional temperature show the similar trends fur all the cases (H=15 mm, 20 mm and 30 mm). The peak augmentation of the distribution of the local non-dimensional temperature occurs in the downwash region near the point of minimum boundary-layer thickness.